AUTOMATION WITH “PRATICO SYSTEM” FOR SLIDING GATES BX SERIES INSTALLATION MANUAL BX-P
“IMPORTANT SAFETY INSTRUCTIONS FOR INSTALLATION” “CAUTION: IMPROPER INSTALLATION MAY CAUSE SERIOUS DAMAGE, FOLLOW ALL INSTALLATION INSTRUCTIONS CAREFULLY” “THIS MANUAL IS ONLY FOR PROFESSIONAL INSTALLERS OR QUALIFIED PERSONS” 1 Legend ENGLISH This symbol indicates sections to be read with particular care. This symbol indicates sections concernig safety This symbol indicates notes to communicate to users.
4.3 Parts description 3 1 GEARMOTOR UNIT 2 4 5 6 9 7 8 ACCESSORIES 1 - R001 - Cylinder lock with DIN keys 2 - BSF - Braking device 3 - BRC - Cable winding device 4 - B4353 - Chain transmission device 5 - CCT - Simple 1/2” chain 6 - CGIU - 1/2” chain joint 7 - CGZ - Galvanized steel 22 x 22 module 4 rack 8 - CGZF - PA 6 nylon 20 x 30 module 4 rack with holes and fixing spacers 9 - CGZS - Galvanized steel 30 x 8 module 4 rack with fastening screws, holes and supports 3 5 6 1 9 2 8 7 4 4.
5 Installation Installation must be carried out by expert qualified personnel and in full observance of regulations in force. Before proceeding with the installation, it is necessary to: • Make sure the door is rigid and compact and that the sliding wheels are well oiled and in good condition. • The ground guide must be well fastened to the ground, fully on the surface for the entirety of its length and without irregularities that might obstruct the gate’s movement.
12345- 67891011- Key-operated selector switch Flashing light indicating door movement Antenna Safety photocells Photocell column Closure stop ENGLISH BX-P unit Control board incorporated Radio receiver Limit-switch tabs Rack 5.4 Motor to base anchorage The following applications are only examples, as the space required for unit installation and the accessories vary depending on dimensions and therefore it is up to the installer to select the best solution.
5.5 Unit installation Rack-to-pinion coupling with 1÷2 mm clearance ¿ MM Horizontal adjustment and unit anchorage Vertical adjustment and unit leveling Cable entrances 5.6 Attaching the rack/limit Attach the rack to the gate as described below: - Release the gearmotor (parag. 5.
5.7 Attaching the switch tabs Position the limit-switch tabs (whose positions determine the limits of gate travel) on the rack. Note: do not allow the gate to strike the mechanical stops in the open or closed positions. All the data and information contained herein is considered subject to change at any time and at our discretion ENGLISH #!-% 5.8 Manual release of the gearmotor To open the access door, insert the key, push down and rotate clockwise.
6 Control board ENGLISH This control board is powered by 230V a.c. across terminals L and N, and is protected by a 5A fuse on the main power line. Control systems are powered by low voltage and protected with by a 1A fuse. The total power consumption of 24V accessories must not exceed 40 W. Photoelectric cells may be connected and set for reopening during closure, partial stop, total stop and detection of an obstacle with the motor turned off.
6.3 Electrical connections , 5 6 7 % 0 # # %" %" &! &# & " " ENGLISH L N . 230 V (a.c.) power supply U W V M 230 V (a.c.) motor All the data and information contained herein is considered subject to change at any time and at our discretion (Condenser) - in motion (e.g. flashing light 25W) W E1 230V output - cycle lamp (max. 60W), to position the dips 1 and 6 in ON +10 -11 1 2 24V powering accessories max. 40W Pushbutton stop (N.C.
6.4 Gearmotor end-stop connection For right-hand installation: - reverse FA-FC of the end stops on the terminal board; - reverse the U-V phases of the motor on the terminal board. ENGLISH Gearmotor end-stop assembly already connected for installation on the left-hand side seen from inside. NC U W V FA FC F U W V COM COM M M All the data and information contained herein is considered subject to change at any time and at our discretion NC F NC FC NC FA 6.
6.6 unction selections (dip-switch) ON OFF /. ENGLISH 1 ON - Automatic closing - The automatic closing timer is automatically activated at the end of the opening cycle. The preset, adjustable automatic closing time is automatically interrupted by the activation of any safety system, and is deactivated after a total stop command or in case of power failure; 2 ON - Radio function command and/or “open-stop-close-stop” button (with radio-frequency card inserted).
7 Installation procedure of the transmitter for remote control Read the three steps below before beginning installation procedures: 7.1 Prepare the radio board (AF1) 1) On AM transmitters operating at 433.92 MHz (TOP and TAM series), position the jumper connection on circuit card AF43S as shown on the sheet. TOP Frequency/MHz Radiofrequecy board Transmitter FM 26.995 AF130 TFM FM 30.900 AF150 TFM AM 433.92 AF43S / AF43SM TAM / TOP AM 433.92 AF43SR ATOMO AM 40.
TOP T434M - T314M 0 0 0 0 TOP T432S - T432SA - T434MA - T432NA - T434NA set code only see instructions on pack P1 = CH1 P2 = CH2 ENGLISH P3 = CH3 P4 = CH4 E CAM All the data and information contained herein is considered subject to change at any time and at our discretion C TAM T432 - T434 - T438 - TAM432SA see instruction sheet inside the pack TFM T132 - T134 - T138 T152 - T154 - T158 see instruction sheet inside the pack 7.
3) Repeat the procedure of parts 1 and 2 with the “CH2” key, associating it wit another transmitter key. N.B.: if the code needs to be changed, repeat the sequence described above. ENGLISH T2 #( #( !& 02/' 8 Installation procedure for the remote control for automatically releasing the motor (pratico system) The “pratico system” automatically releases the automation through the radio transmitter.
8.2 Battery connection and memorization of the code on the control board Terminal -, + Transformer All the data and information contained herein is considered subject to change at any time and at our discretion ENGLISH 1) Insert the terminal (-, +) connected to the battery to the free coupling of the motherboard. Note: the board must be batterypowered for saving procedures. Check the LED signalling 230V power is off. Electric lock , .
9 Connection of two paired ratiomotors with a single control 1) Coordinate ratiomotor A and B’s movement direction, changing the rotation of motor B (see paragraph 6.4 ratiomotor/end-stop connection). B A , . 5 6 3) Perform the same settings and functions (dip-switch) on both boards. 7 % 0 %" %" # # &! &# & 2) Perform the electric connections on motor A’s control board as instructed in paragraph 6.3 electric connections, page 9. " " B A ,).
9 Maintenance 9.1 Periodic maintenance The unit does not require specific maintenance. Only as a precautionary measure and in case of intensive use, it is opportune to periodically (every six months) check that the electric cables are in good condition and that the bolts and nuts are tight, and oil the contact areas between the fixed and mobile sliding pieces. All checks must be recorded (in a dedicated record-book).
CAME UNITED KINGDOM LTD UNIT 3, ORCHARD BUSINESS PARK TOWN STREET, SANDIACRE NOTTINGHAM - NG10 5BP - U.K. Tel 0044 115 9210430 Cod. 119BT85 ver. 1.
