AUTOMATION FOR SWING GATES AMICO SERIES INSTALLATION MANUAL A1824
“IMPORTANT INSTALLATION, SAFETY INSTRUCTIONS” “CAUTION: IMPROPER INSTALLATION MAY CAUSE SERIOUS DAMAGE, FOLLOW ALL INSTALLATION INSTRUCTIONS CAREFULLY” “THIS MANUAL IS ONLY FOR PROFESSIONAL OR QUALIFIED INSTALLERS” ENGLISH 1 Legend of symbols This symbol tells you to read the section with particular care. This symbol tells you that the sections concern safety issues. This symbol tells you what to say to the end-users.
4.3 Description of parts A1824 1 ENGLISH 1) Operator 2) Pilaster bracket 3) Gate bracket 4) Screw, bushing and nut for the pilaster bracket 5) Bolt and nut for the gate bracket 6) Distanziale per perno attacco 6 5 4 3 2 The data and information shown in this manual may be changed by CAME cancelli automatici s.p.a. at any time without prior warning. 4.
5.2 Tools and materials ENGLISH Make sure you have all the tools and materials you will need for the installation at hand to work in total safety and compliance with the current standards and regulations. The following figure illustrates the minimum equipment needed by the installer.
.5 Installing the operator The following illustrations are only examples, given that the space available for anchoring the operator and accessories may vary from gate to gate. It is up to the installer, thus, to choose the most suitable solution. The data and information shown in this manual may be changed by CAME cancelli automatici s.p.a. at any time without prior warning. ENGLISH Lay the corrugated tubing needed for the connections deriving from the junction box. N.B.
ENGLISH Assemble and weld the two parts of the pillar bracket. Secure the bracket to the point you have chosen with proper plugs and screws or – if the pillar is made of metal – weld it on. Note: on non-metal gate leaves assemble and weld the two parts of the bracket and secure them with proper screws. Secure the Insert the bushing (lubricated) into the pillar bracket’s hole. The bracket has holes that allow the opening angle to be changed. Secure the tail joint to the bracket.
Insert the bushing into the head attachment pin. ENGLISH Bushing The data and information shown in this manual may be changed by CAME cancelli automatici s.p.a. at any time without prior warning. Open the gate leaf and insert the pin into the gate bracket. Attachment pin Washer Nut M12 Release the gearmotor (see paragraph on manual release), completely open the gate leaf, loosen the nuts of the opening mechanical stop and position it up against the attachment pin, then secure it.
5.6 Manual release of the gearmotor 5.7 Connecting to the control panel For the electrical connection procedures, use the junction box and branching boxes. Connecting the 24V d.c. delayed closing gearmotor ZL90 Control panel - . %.# Connecting the 24V d.c. delayed opening gearmotor - . %.# , . Power 230V a.c. - 50/60 Hz 8 - . %.# - . %.# The data and information shown in this manual may be changed by CAME cancelli automatici s.p.a. at any time without prior warning.
5.8 Outward opening installation B (mm) E (mm) 90° 130 130 720 Weld the extra bracket to that of the pillar, secure the extra bracket to the pillar making sure the A and B quotas are met as shown in the table. Open the gate to a 90° arc, weld or secure using proper screws the gate bracket making sure the E quota is met. Secure the gearmotor to the brackets. " % A (mm) ENGLISH Opening The data and information shown in this manual may be changed by CAME cancelli automatici s.p.a.
7 Safety instructions This product must only be employed for its originally intended use. Any other use is wrong and potentially dangerous. The manufacturer cannot be held liable for any damages resulting from wrongful, erroneous or negligent uses. Avoid working close to the hinges or other moving mechanical parts. Stay out of the opening/closing arc when operator is in motion. Do not exercise force against the motion of the operator as this could result in potentially dangerous situations.
8 Maintenance 8.1 Periodic maintenance The data and information shown in this manual may be changed by CAME cancelli automatici s.p.a. at any time without prior warning. Make sure there are no plants within the photocell’s beam, and that the gate motion is free of any obstacles. 8.
Periodic maintenance log for end-user (every 6 moths) Notes Signature 8.3 Extra-ordinary maintenance The following table serves to note down any extraordinary maintenance, repairs or improvements performed by specialised firms. N.B.: Any extraordinary maintenance must be performed by specialised technicians.
Installer’s stamp Operator name Date of job Technician’s signature Requester’s signature Installer’s stamp ENGLISH Job performed _____________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ Operator name Date of job Technician’s signature Requester’s signature The data and information sh
CAME UNITED KINGDOM LTD UNIT 3, ORCHARD BUSINESS PARK TOWN STREET, SANDIACRE NOTTINGHAM - NG10 5BP - U.K. Tel - 0044 115 9210430 Cod. 119DU20 ver. 0.2 12/06 © CAME cancelli automatici s.p.a.
