User's Manual
Table Of Contents
- 1 Overview
- 2 Installation, wiring and debugging
- 3 Getting Started
- 4.Basic Functions
- 4.1 Management menu operations
- 4.1.1 Change Admin Password
- 4.1.2 Set or delete Super-open-password
- 4.1.3 Set admin card
- 4.1.4 Delete admin card
- 4.1.5 Set Machine Mode
- 4.1.6 Limits types of reading card
- 4.1.7 Restore to default settings
- 4.1.8 Add User
- 4.1.9 Delete user
- 4.1.10 Set open door methods
- 4.1.11 Set Multi-card to open door
- 4.1.12 Set lock working mode
- 4.1.13 Set Limits User Mode
- 4.1.14 Set Open-time
- 4.1.15 Set notification to close door
- 4.1.16 Set Alarm-time
- 4.1.17 Set Anti-dismantle alarm function
- 4.1.18 Set alarm or doorbell output function
- 4.1.19 Set Anti-crack function
- 4.1.20 Set LED indicator light mode
- 4.1.21 Adjust the brightness of the normally brigh
- 4.1.22 Set key backlit mode
- 4.1.23 Adjust brightness of key backlit
- 4.1.24 Set buzzer mode
- 4.1.25 Adjust key volume
- 4.1.26 Set the # key whether it can be used doorbe
- 4.1.27 Set doorbell key mode
- 4.2.28Set reader output format
- 4.2 Admin card or PIN operation
- 4.3Users operation
- 4.4 Other operations
- 4.5 Operation characteristics in different machine
- 4.1 Management menu operations
- 5 Management menu summary table
- 6 Precautions in use
- 7 Common troubleshooting
- 25 -
4.2.7 Authorization-card operation
Read Authorization-card once, two short beeps, limit users.
Read Authorization-card again, one long beep, release limit.
Note: Authorization-card is also called header card, it authorizes users. By default, users can operate properly, you can use
an Authorization-card when you need to restrict user access.
4.2.8 Normal-open-card operation
Read Normal-open-card once, two short beeps, lock keep open, not controlled by other unlocking action.
Read Normal-open-card again, one long beep, release normal open state.
4.3 Users operation
4.3.1 Get user card or PIN
Users must obtain the user card or user PIN from the administrator for the first time. Among them, the user PIN can be
obtained separately from the administrator, and can also be changed by the user card. The user card and the user PIN are
divided into first zones and second zones, they operate the door of the corresponding zone respectively.
T
he number of user
PIN is specified, zone 1 is 4-6 digits, and zone 2 is fixed 7 digits. We take Zone1 as sample, it is the same in zone 2. Only
PIN digits and LED color difference, see indicator light and buzzer prompt.
4.3.2 Change user PIN
Change user PIN by card:
* (Hold down for more than 2 seconds), read card, (Old PIN)#, (New PIN)#, (Repeat new PIN)#
Note: Every card’s default PIN is 1234 which can’t be use to open door unless you change it.
Change user PIN by ID number:
*( Hold down for more than 2 seconds), (ID number), (Old PIN)#, (New PIN)#, (Repeat new PIN)#
Note: You need to know ID when you change PIN through this method. ID number needs to be obtained from the
administrator. The old PIN cannot be the initial PIN 1234.
4.3.3 User Open door
Open door by Single card:
read user card
Open door by multi-card:
Read user card, read user card, ...
Open door by User card or PIN:
Read user card or (User PIN)#
Open door by User card and PIN:
Read user card, (User PIN)#