Operation Manual
751R V2azur
5
ENGLISH
1
Standby/On
Switches the unit between Standby mode (indicated by a dim power LED)
and On (indicated by a bright power LED). Standby is an eco-friendly <0.5W
low power mode. The unit may be left in Standby mode when not in use.
2
Phones
Allows for the connection of stereo headphones with a 6.35mm/ΒΌ" Jack
plug. Headphones with an impedance of between 32 and 600 ohms are
recommended.
Note: Plugging in headphones will automatically mute the main and pre-amp
outputs and select a Dolby Headphones output to be created for headphone
use.
3
Tuning +/-
Used to tune FM/AM frequencies and skip presets for the built-in Tuner.
4
Mode/Store
Press to cycle between Tuner modes. Press and hold for storing presets
(refer to the 'Operating Instructions' of this manual for more information).
5
Infrared sensor
Receives IR commands from the supplied remote control. A clear,
unobstructed line of sight between the remote control and the sensor is
required.
6
Display
Displays the status of the unit.
7
Tuner FM/AM
Press to select the tuner. Once in Tuner mode press to switch between FM
and AM modes.
Note: The 751R V2 remembers the audio and video input type and
processing mode for each individual source input. These are recalled each
time a source is selected.
8
HDMI Preview
Press to see the previews of different HDMI sources connected to the unit.
Use the remote control navigational button or use the Tuning +/- to navigate
and press the Mode/Store button to activate the chosen preview display.
9
USB
Press to select the USB Audio source connected to the USB input at the back.
10
BD/DVD
Press to select the source equipment connected to the BD/DVD input.
11
Video 1
Press to select the source equipment connected to the Video 1 input.
12
Video 2
Press to select the source equipment connected to the Video 2 input.
13
Recorder 1
Press to select the source equipment connected to the Recorder 1 input.
14
Aux/TV
Press to select the source equipment connected to the Aux input.
With ARC enabled (see later section), press again to select Audio Return
Channel from a suitable TV.
15
CD
Press to select the source equipment connected to the CD input.
16
Recorder 2
Press to select the source equipment connected to the Recorder 2 input.
17
Audio input type
Press this button to select between analogue, digital (optical/coaxial) or
HDMI input types as the source of the audio for the currently selected source
input.
The choices available depend on the inputs that have been assigned to that
source, see later section.
18
Stereo modes
Press to listen to a source in either digitally processed stereo or stereo and
sub modes.
19
Surround modes
Press to select Dolby Digital or DTS surround modes (with suitably encoded
digital source material), or various Dolby Pro Logic II/IIx/IIz, DTS Neo:6
modes for matrix encoded analogue or digital material.
Post-processing of digital surround types with Dolby Pro Logic IIx/IIz or Neo:6
is also possible. See later decode mode tables for details.
20
Picture adjustment
Press to select various picture adjustments for sources that have the Scaler
set to Process only (see 'Source setup' section in the manual). An adjustment
bar will appear on the TV for the current item (Brightness, Contrast etc.)
Press the Pic. Adj. button again to move to the next item.
Use the volume knob to adjust the level of the current parameter.
Note: For source material, the scaler cannot process (such as deep colour or
3D content). Pic. Adj. will have no effect.
This button is also used to change the scaler output resolution. Press and
hold the button for 10 seconds and the current output resolution will appear
on the 751R V2's front panel display. Keep holding the button down and the
751R V2 will change to the next available resolution and show it on the front
panel display. See later section.
1 2 3 4 5
17 18 19 20 21
6
9 10 11 12 13 14 15 16
22
23 24
25
26
7 8
Front panel controls