Owner's Manual
7
AXC25
AXC35
LOADING AND UNLOADING DISCS
1. Press the Open/Close button.
2. When the disc tray has opened fully, place a disc carefully in the tray with the
label side facing up.
3. To close the disc tray, press the Open/Close button again. When the tray, with a
correctly loaded disc, is fully closed the CD player will read the disc and display
the content information.
4. The disc tray can be opened at any time by pressing the Open/Close button. Only
remove the disc after the tray has fully opened.
Note:
– Do not put anything except a compact disc into the tray. Foreign objects may
damage the mechanism.
– Do not force the tray by hand during the opening and closing operations.
– To avoid dirt and dust entering the mechanism, keep the disc tray closed.
– If the compact disc is badly scratched or too dirty, the player may not be able to
read it or play it.
– Never load more than one disc into the disc tray at any time.
NORMAL DISC PLAY
This unit has been designed to play compact discs, recordable CDs
(CD-R) and re-writable CDs (CD-RW) bearing the identication
logo shown here. No other discs can be used. The CD-R/CD-RW
discs should contain properly recorded TOC (Table of Contents) information so that
they can be played back. This unit can play only the discs recorded in the CDDA
format designed for music reproduction or those containing MP3 or WMA les. Do
not attempt to play a disc on this unit containing other data, such as a data CD-ROM
for PCs.
1. Switch on your amplier and set its input selector to the correct position. Adjust
the volume control to a minimum.
2. Press the Open/Close button to open the disc tray and load a disc.
3. Press the Open/Close button again to close the tray. The CD player will read the
disc.
4. To begin playback, press the button.
5. When the last track has nished playing, the display will return to Table of
Contents (TOC).
6. To stop the disc at any point, press the button. Pressing the button while
the disc is playing will pause the disc. Playback can be resumed by pressing
button.
LOCATING A SPECIFIC TRACK DURING PLAYBACK
1. A single short press of the button will take you to the beginning of the next
track on the CD. Repeat as necessary.
2. A single short press of the button will take you to the beginning of the
previous track.
LOCATING A SPECIFIC TRACK WHEN PLAYBACK IS
STOPPED
1. A single short press of the buttons will skip between tracks.
2. Press to start playback from the selected track.
REPEATING DISCS AND TRACKS
1. Ensure that the disc is loaded.
2. To repeat a specic track, press the Repeat button on the remote. ‘RPT ONE’ will
appear on the display. Press and the selected track will now repeat until the
function is turned o. Alternatively, press the Repeat button, select the chosen
track using the numerical buttons on the remote control and press .
3. Press the Repeat button twice on the remote control. ‘RPT ALL’ will appear on
the display. Press . The whole disc will now be repeated until the function is
turned o.
4. To turn the Repeat function o, press the Repeat button either before or during
playback until ‘RPT OFF’ appear on the display.
PLAYING TRACKS IN RANDOM ORDER
1. Ensure that a disc is loaded.
2. Press the Random button on the remote control. ‘RAN ON’ will appear on the
display.
3. Press . The CD player will now play the entire disc in random order. It is also
possible to press the Random button during playback to listen to tracks in
random order.
4. Press the Random button to exit. The disc will continue playing to the end in the
correct order.
5. Press the button at any time to stop the disc.
Note: Selecting ‘Random’ mode when ‘RPT ONE’ has been selected will automatically
cancel ‘RPT ONE’ mode.
USING THE REMAIN FUNCTION
1. Ensure that the disc is playing.
2. Press the Remain button on the remote control once to display the time
remaining for the track playing.
3. Pressing the Remain button the second time will show the total remaining disc
time.
4. Press the Remain button again either before or during playback to return to
normal play mode.
PROGRAMMING DISC PLAY
It is possible to program the AXC35/AXC25 to play back in any order only the tracks
you wish to listen to.
1. Ensure that a disc is loaded. The display should show the TOC data.
2. Press the Prog button on the remote control. The Program set-up will appear on
the display.
3. Use the buttons or enter the track number that you want to program as
your rst track.
4. Press the Prog button on the remote. The desired track is now programmed. The
program number automatically increases by one for the next entry.
5. Repeat steps three and four until all your desired tracks are entered. A
maximum of 20 tracks can be programmed.
6. Press the button to begin programmed playback.
7. Press the Prog Clear button on the remote to clear all programmed tracks.
Operating instructions