User Manual

ManualsBrandsCambium Networks ManualsElectronicsPoint to Point Wireless Bridge

Table Of Contents

1 About This User Guide
- 1.1 Interpreting Typeface and Other Conventions
- 1.2 Getting Additional Help
- 1.3 Sending Feedback
2 Avoiding Hazards
- 2.1 Preventing Overexposure to RF Energy
  - 2.1.1 Calculations for Separation Distances and Power Compliance Margins
    - 2.1.1.1 Calculated Distances and Power Compliance Margins
Getting Started
- 3.1 For Your Safety
- 3.2 Welcome
- 3.3 Product Description
- 3.4 Warranty
4 Product Architecture
5 General Considerations
- 5.1 Spectrum Planning
- 5.2 Licenses and Region Codes
- 5.3 Operational Restrictions
  - 5.3.1 Radar Avoidance
  - 5.3.2 5.8GHz Restrictions
    - 5.3.2.1 RTTT Avoidance and Other Channel Use Restrictions
    - 5.3.2.2 Radar Avoidance, i-DFS and Bandwidth Operation
- 5.4 Channel Bandwidth Operation
- 5.5 PTP 54500 Specific Frequency Planning Considerations
  - 5.5.1 PTP 54500 Raster Considerations:
  - 5.5.2 Transmit Power Reduction at the Band Edges
- 5.6 PTP 58500 Specific Frequency Planning Considerations
  - 5.6.1 PTP 58500 Raster Considerations
  - 5.6.2 PTP 58500 Transmit Power Reduction at the Band Edges
- 5.7 Distance
- 5.8 Networking Information
- 5.9 Lightning Protection and Regulations
- 5.10 Electrical Requirements
6 Site Planning
- 6.1 Site Selection Criteria
7 Installation
- 7.1 Preparation
- 7.2 Installation Procedure
- 7.3 Tools Required
- 7.4 Installation Support
- 7.5 Legal Disclaimer
- 7.6 Mounting the ODUs
- 7.7 Connecting Up
8 Web Page Reference
- 8.1 Home Page – PTP 500 Series Bridge
  - 8.1.1 Home Page Alarm Display
- 8.2 Systems Status Page
- 8.3 System Administration Pages
9 Recovery Mode
- 9.1 Upgrade Software Image
- 9.2 Reset IP & Ethernet Configuration
- 9.3 Erase Configuration
- 9.4 Erase Security Parameters
- 9.5 Reboot
10 Fault Finding
- 10.1 Hardware
- 10.2 Radio
  - 10.2.1 No Activity
  - 10.2.2 Some Activity
11 Lightning Protection
- 11.1 Overview
  - 11.1.1 Lightning Protection Zones
- 11.2 Detailed Installation
- 11.3 Testing Your Installation
  - 11.3.1 Pre-Power Testing
  - 11.3.2 Post-Power Testing
- 11.4 Locating the Fault
12 Wind Loading
- 12.1 General
- 12.2 Calculation of Lateral Force
- 12.3 Capabilities of the PTP 500 Series Bridges
- 12.4 Wind Speed Statistics
13 PTP 500 Series Bridge – Connectorized Model
- 13.1 Scope
- 13.2 Product Description
- 13.3 Software/Features
- 13.4 Deployment Considerations
- 13.5 Link Budget
- 13.6 Regulatory Issues
- 13.7 Installation
- 13.8 Additional Lightning Protection
  - 13.8.1 ODU Mounted Outdoors
  - 13.8.2 ODU Mounted Indoors
14 Data Rate Calculations
15 AES Encryption Upgrade
- 15.1 Configuring Link Encryption
  - 15.1.1 License Keys
  - 15.1.2 Encryption Mode and Key
- 15.2 Wireless Link Encryption FAQ
16 Legal and Regulatory Notices
- 16.1 Important Note on Modifications
- 16.2 National and Regional Regulatory Notices – PTP 58500 variant
- 16.3 National and Regional Regulatory Notices – PTP 54500 Variant
  - 16.3.1 FCC and Industry Canada (IC) Notification
  - 16.3.2 European Union Notification
- 16.4 Exposure
- 16.5 Legal Notices
17 Specifications
- 17.1 System Specifications
- 17.2 Safety Compliance
- 17.3 EMC Emissions Compliance
  - 17.3.1 PTP 54500 Variant
  - 17.3.2 PTP 58500 Variant
- 17.4 EMC Immunity Compliance
- 17.5 Radio Certifications
  - 17.5.1 PTP 54500 Variant
  - 17.5.2 PTP 58500 Variant
- 17.6 Environmental Specifications
- 17.7 System Connections
  - 17.7.1 PIDU Plus to ODU and ODU to Network Equipment Connections
18 FAQs
19 Glossary
20 Index

8 Web Page Reference

132

8.3.10 Remote Management Page

The Remote Management page (Figure 66) allows the system administrator to configure the

remote management of the PTP 500 Series Bridge.

Figure 66 - Remote Management