Installation Guide
Table Of Contents
- PMP 450i and PTP 450i Configuration and User Guide
- Safety and regulatory information
- Contents
- List of Figures
- List of Tables
- About This Configuration and User Guide
- Chapter 1: Reference information
- Chapter 2: Configuration
- Preparing for configuration
- Task 1: Connecting to the unit
- Task 2: Configuring IP and Ethernet interfaces
- Configuring the AP IP interface
- NAT, DHCP Server, DHCP Client and DMZ in SM
- Configuring the SM IP interface with NAT disabled
- Configuring the SM IP interface with NAT enabled
- NAT tab of the SM with NAT disabled
- NAT tab of the SM with NAT enabled
- Reconnecting to the management PC
- VLAN Remarking and Priority bits configuration
- VLAN tab of the AP
- VLAN tab of the SM
- VLAN Membership tab of the SM
- PPPoE tab of the SM
- NAT Port Mapping tab of the SM
- Task 3: Upgrading the software version and using CNUT
- Task 4: Configuring General and Unit settings
- Task 5: Configuring security
- Isolating APs from the internet
- Encrypting radio transmissions
- Managing module access by passwords
- Requiring SM Authentication
- Filtering protocols and ports
- Encrypting downlink broadcasts
- Isolating SMs
- Filtering management through Ethernet
- Allowing management only from specified IP addresses
- Configuring management IP by DHCP
- Restricting radio Telnet access over the RF interface
- Security tab of the AP
- Filtering protocols and ports
- Protocol Filtering tab of the AP
- Port configuration tab of the AP
- Security tab of the SM
- Protocol Filtering tab of the SM
- Port Configuration tab of the SM
- Task 6: Configuring radio parameters
- Task 7: Setting up SNMP agent
- Task 8: Configuring syslog
- Task 9: Configuring remote access
- Task 10: Monitoring the AP-SM Link
- Task 11: Configuring quality of service
- Maximum Information Rate (MIR) Parameters
- Token Bucket Algorithm
- MIR Data Entry Checking
- Committed Information Rate (CIR)
- Bandwidth from the SM Perspective
- Interaction of Burst Allocation and Sustained Data Rate Settings
- High-priority Bandwidth
- Traffic Scheduling
- Setting the Configuration Source
- Quality of Service (QoS) tab of the AP
- DiffServ tab of the AP
- Quality of Service (QoS) tab of the SM
- DiffServ tab of the SM
- Task 12: Performing an Sector Wide SA
- Task 13: Zero Touch Configuration Using DHCP Option 66
- Task 14: Configuring Radio via config file
- Task 15: Configuring a RADIUS server
- Understanding RADIUS for PMP 450i
- Choosing Authentication Mode and Configuring for Authentication Servers - AP
- SM Authentication Mode – Require RADIUS or Follow AP
- Handling Certificates
- Configuring your RADIUS servers for SM authentication
- Assigning SM management IP addressing via RADIUS
- Configuring your RADIUS server for SM configuration
- Using RADIUS for centralized AP and SM user name and password management
- RADIUS Device Data Accounting
- RADIUS Device Re-authentication
Task 4: Configuring General and Unit settings PMP 450i and PTP 450i Configuration and User
Guide
Table 24 SM Unit Settings attributes
Attribute Meaning
Set to Factory
Defaults Upon
Default Plug
Detection
If Enabled is checked, then an override/default plug functions as a
default plug. When the module is rebooted with the plug inserted, it
can be accessed at the IP address 169.254.1.1 and no password, and
all parameter values are reset to defaults. A subscriber, technician, or
other person who gains physical access to the module and uses an
override/default plug
cannot
see or learn the settings that were
previously configured in it. When the module is later rebooted with no
plug inserted, the module uses the new values for any parameters
that were changed and the default values for any that were not.
If Disabled is checked, then an override/default plug functions as an
override plug. When the module is rebooted with the plug inserted, it
can be accessed at the IP address 169.254.1.1 and no password, and
all previously configured parameter values remain and are displayed.
A subscriber, technician, or other person who gains physical access
to the module and uses an override/default plug
can
see and learn the
settings. When the module is later rebooted with no plug inserted, the
module uses the new values for any parameters that were changed
and the previous values for any that were not.
See Overriding Forgotten IP Addresses or Passwords on AP on Page
83.
LED Panel Mode Legacy Mode configures the radio to operate with standard LED
behavior (see section “SM Interfaces” in the
PMP 450i Planning
Guide
or in the
PMP 450i Installation Guide
)
Undo Unit-Wide
Saved Changes
When you click this button, any changes that you made in any tab but
did not commit by a reboot of the module are undone.
Set to Factory
Defaults
When you click this button,
all configurable parameters on all tabs
are reset to the factory settings.
This can be reverted by selecting "Undo Unit-Wide Saved Changes",
before
rebooting the radio.
Configuration File This allows to download the configuration file of the radio. This
configuration file contains the complete configuration including all
the default values. The configuration file is highlighted as
downloadable link and the naming convention is “<mac address of
AP>.cfg”.
Status of
Configuration file
This section shows the results of the Configuration file.
pmp-0957 (April 2015) 75