Installation Guide
Table Of Contents
- PMP 450i and PTP 450i Configuration and User Guide
- Safety and regulatory information
- Contents
- List of Figures
- List of Tables
- About This Configuration and User Guide
- Chapter 1: Reference information
- Chapter 2: Configuration
- Preparing for configuration
- Task 1: Connecting to the unit
- Task 2: Configuring IP and Ethernet interfaces
- Configuring the AP IP interface
- NAT, DHCP Server, DHCP Client and DMZ in SM
- Configuring the SM IP interface with NAT disabled
- Configuring the SM IP interface with NAT enabled
- NAT tab of the SM with NAT disabled
- NAT tab of the SM with NAT enabled
- Reconnecting to the management PC
- VLAN Remarking and Priority bits configuration
- VLAN tab of the AP
- VLAN tab of the SM
- VLAN Membership tab of the SM
- PPPoE tab of the SM
- NAT Port Mapping tab of the SM
- Task 3: Upgrading the software version and using CNUT
- Task 4: Configuring General and Unit settings
- Task 5: Configuring security
- Isolating APs from the internet
- Encrypting radio transmissions
- Managing module access by passwords
- Requiring SM Authentication
- Filtering protocols and ports
- Encrypting downlink broadcasts
- Isolating SMs
- Filtering management through Ethernet
- Allowing management only from specified IP addresses
- Configuring management IP by DHCP
- Restricting radio Telnet access over the RF interface
- Security tab of the AP
- Filtering protocols and ports
- Protocol Filtering tab of the AP
- Port configuration tab of the AP
- Security tab of the SM
- Protocol Filtering tab of the SM
- Port Configuration tab of the SM
- Task 6: Configuring radio parameters
- Task 7: Setting up SNMP agent
- Task 8: Configuring syslog
- Task 9: Configuring remote access
- Task 10: Monitoring the AP-SM Link
- Task 11: Configuring quality of service
- Maximum Information Rate (MIR) Parameters
- Token Bucket Algorithm
- MIR Data Entry Checking
- Committed Information Rate (CIR)
- Bandwidth from the SM Perspective
- Interaction of Burst Allocation and Sustained Data Rate Settings
- High-priority Bandwidth
- Traffic Scheduling
- Setting the Configuration Source
- Quality of Service (QoS) tab of the AP
- DiffServ tab of the AP
- Quality of Service (QoS) tab of the SM
- DiffServ tab of the SM
- Task 12: Performing an Sector Wide SA
- Task 13: Zero Touch Configuration Using DHCP Option 66
- Task 14: Configuring Radio via config file
- Task 15: Configuring a RADIUS server
- Understanding RADIUS for PMP 450i
- Choosing Authentication Mode and Configuring for Authentication Servers - AP
- SM Authentication Mode – Require RADIUS or Follow AP
- Handling Certificates
- Configuring your RADIUS servers for SM authentication
- Assigning SM management IP addressing via RADIUS
- Configuring your RADIUS server for SM configuration
- Using RADIUS for centralized AP and SM user name and password management
- RADIUS Device Data Accounting
- RADIUS Device Re-authentication
Task 2: Configuring IP and Ethernet interfaces PMP 450i and PTP 450i Configuration and User
Guide
Attribute Meaning
Provider VID The provider VID is used for the S-tag. It is only used if the
Port Type is Q-in-Q and will always be used for the S-tag. If
an existing 802.1Q frame arrives, the Provider VID is what is
used for adding and removing of the outer S-tag. If an
untagged frame arrives to a Q-in-Q port, then the Provider
VID is the S-tag and the Default Port VID (or Port VID MAC
Address Mapping, if valid) is used for the C-tag.
Active
Configuration,
Default Port VID
This is the value of the parameter of the same name, configured
above.
Active
Configuration,
MAC Address
VID Map
This is the listing of the MAC address VIDs configured in Port
VID MAC Address Mapping.
Active
Configuration,
Management
VID
This is the value of the parameter of the same name, configured
above.
Active
Configuration,
SM Management
VID Pass-
Through
This is the value of the parameter of the same name, configured
above.
Active
Configuration,
Dynamic Aging
Timeout
This is the value of the VLAN Aging Timeout parameter
configured above.
Active
Configuration,
Allow Learning
Yes is displayed if the value of the Dynamic Learning
parameter above is Enabled. No is displayed if the value of
Dynamic Learning is Disabled.
Active
Configuration,
Allow Frame
Type
This displays the selection that was made from the drop-down
list at the Allow Frame Types parameter above.
Active
Configuration,
QinQ
This is set to Enabled if VLAN Port Type is set to QinQ, and
is set to Disabled if VLAN Port Type is set to Q.
Active
Configuration,
QinQ EthType
This is the value of the QinQ EtherType configured in the AP.
pmp-0957 (April 2015) 49