Installation Guide
Table Of Contents
- PMP 450i and PTP 450i Configuration and User Guide
- Safety and regulatory information
- Contents
- List of Figures
- List of Tables
- About This Configuration and User Guide
- Chapter 1: Reference information
- Chapter 2: Configuration
- Preparing for configuration
- Task 1: Connecting to the unit
- Task 2: Configuring IP and Ethernet interfaces
- Configuring the AP IP interface
- NAT, DHCP Server, DHCP Client and DMZ in SM
- Configuring the SM IP interface with NAT disabled
- Configuring the SM IP interface with NAT enabled
- NAT tab of the SM with NAT disabled
- NAT tab of the SM with NAT enabled
- Reconnecting to the management PC
- VLAN Remarking and Priority bits configuration
- VLAN tab of the AP
- VLAN tab of the SM
- VLAN Membership tab of the SM
- PPPoE tab of the SM
- NAT Port Mapping tab of the SM
- Task 3: Upgrading the software version and using CNUT
- Task 4: Configuring General and Unit settings
- Task 5: Configuring security
- Isolating APs from the internet
- Encrypting radio transmissions
- Managing module access by passwords
- Requiring SM Authentication
- Filtering protocols and ports
- Encrypting downlink broadcasts
- Isolating SMs
- Filtering management through Ethernet
- Allowing management only from specified IP addresses
- Configuring management IP by DHCP
- Restricting radio Telnet access over the RF interface
- Security tab of the AP
- Filtering protocols and ports
- Protocol Filtering tab of the AP
- Port configuration tab of the AP
- Security tab of the SM
- Protocol Filtering tab of the SM
- Port Configuration tab of the SM
- Task 6: Configuring radio parameters
- Task 7: Setting up SNMP agent
- Task 8: Configuring syslog
- Task 9: Configuring remote access
- Task 10: Monitoring the AP-SM Link
- Task 11: Configuring quality of service
- Maximum Information Rate (MIR) Parameters
- Token Bucket Algorithm
- MIR Data Entry Checking
- Committed Information Rate (CIR)
- Bandwidth from the SM Perspective
- Interaction of Burst Allocation and Sustained Data Rate Settings
- High-priority Bandwidth
- Traffic Scheduling
- Setting the Configuration Source
- Quality of Service (QoS) tab of the AP
- DiffServ tab of the AP
- Quality of Service (QoS) tab of the SM
- DiffServ tab of the SM
- Task 12: Performing an Sector Wide SA
- Task 13: Zero Touch Configuration Using DHCP Option 66
- Task 14: Configuring Radio via config file
- Task 15: Configuring a RADIUS server
- Understanding RADIUS for PMP 450i
- Choosing Authentication Mode and Configuring for Authentication Servers - AP
- SM Authentication Mode – Require RADIUS or Follow AP
- Handling Certificates
- Configuring your RADIUS servers for SM authentication
- Assigning SM management IP addressing via RADIUS
- Configuring your RADIUS server for SM configuration
- Using RADIUS for centralized AP and SM user name and password management
- RADIUS Device Data Accounting
- RADIUS Device Re-authentication
PMP 450i and PTP 450i Configuration and User
Task 2: Configuring IP and Ethernet interfaces
Attribute Meaning
DHCP Server
Enable/Disable
This parameter is not configurable when NAT is
disabled.
DHCP Server Lease
Timeout
This parameter is not configurable when NAT is
disabled.
DHCP Start IP This parameter is not configurable when NAT is
disabled.
Number of IPs to Lease This parameter is not configurable when NAT is
disabled.
DNS Server Proxy This parameter is not configurable when NAT is
disabled.
DNS IP Address This parameter is not configurable when NAT is
disabled.
Preferred DNS IP
Address
This parameter is not configurable when NAT is
disabled.
Alternate DNS IP
Address
This parameter is not configurable when NAT is
disabled.
Remote Management
Interface
This parameter is not configurable when NAT is
disabled.
Connection Type This parameter is not configurable when NAT is
disabled.
IP Address This parameter is not configurable when NAT is
disabled.
Subnet Mask This parameter is not configurable when NAT is
disabled.
Gateway IP Address This parameter is not configurable when NAT is
disabled.
DNS IP Address
This parameter is not configurable when NAT is
disabled.
Preferred DNS Server
This parameter is not configurable when NAT is
disabled.
Alternate DNS Server
This parameter is not configurable when NAT is
disabled.
Domain Name
This parameter is not configurable when NAT is
disabled.
ARP Cache Timeout If a router upstream has an ARP cache of longer
duration (as some use 30 minutes), enter a value of
longer duration than the router ARP cache. The default
value of this field is 20 minutes.
32
pmp-0957 (April 2015)