Installation Guide
Table Of Contents
- PMP 450i and PTP 450i Configuration and User Guide
- Safety and regulatory information
- Contents
- List of Figures
- List of Tables
- About This Configuration and User Guide
- Chapter 1: Reference information
- Chapter 2: Configuration
- Preparing for configuration
- Task 1: Connecting to the unit
- Task 2: Configuring IP and Ethernet interfaces
- Configuring the AP IP interface
- NAT, DHCP Server, DHCP Client and DMZ in SM
- Configuring the SM IP interface with NAT disabled
- Configuring the SM IP interface with NAT enabled
- NAT tab of the SM with NAT disabled
- NAT tab of the SM with NAT enabled
- Reconnecting to the management PC
- VLAN Remarking and Priority bits configuration
- VLAN tab of the AP
- VLAN tab of the SM
- VLAN Membership tab of the SM
- PPPoE tab of the SM
- NAT Port Mapping tab of the SM
- Task 3: Upgrading the software version and using CNUT
- Task 4: Configuring General and Unit settings
- Task 5: Configuring security
- Isolating APs from the internet
- Encrypting radio transmissions
- Managing module access by passwords
- Requiring SM Authentication
- Filtering protocols and ports
- Encrypting downlink broadcasts
- Isolating SMs
- Filtering management through Ethernet
- Allowing management only from specified IP addresses
- Configuring management IP by DHCP
- Restricting radio Telnet access over the RF interface
- Security tab of the AP
- Filtering protocols and ports
- Protocol Filtering tab of the AP
- Port configuration tab of the AP
- Security tab of the SM
- Protocol Filtering tab of the SM
- Port Configuration tab of the SM
- Task 6: Configuring radio parameters
- Task 7: Setting up SNMP agent
- Task 8: Configuring syslog
- Task 9: Configuring remote access
- Task 10: Monitoring the AP-SM Link
- Task 11: Configuring quality of service
- Maximum Information Rate (MIR) Parameters
- Token Bucket Algorithm
- MIR Data Entry Checking
- Committed Information Rate (CIR)
- Bandwidth from the SM Perspective
- Interaction of Burst Allocation and Sustained Data Rate Settings
- High-priority Bandwidth
- Traffic Scheduling
- Setting the Configuration Source
- Quality of Service (QoS) tab of the AP
- DiffServ tab of the AP
- Quality of Service (QoS) tab of the SM
- DiffServ tab of the SM
- Task 12: Performing an Sector Wide SA
- Task 13: Zero Touch Configuration Using DHCP Option 66
- Task 14: Configuring Radio via config file
- Task 15: Configuring a RADIUS server
- Understanding RADIUS for PMP 450i
- Choosing Authentication Mode and Configuring for Authentication Servers - AP
- SM Authentication Mode – Require RADIUS or Follow AP
- Handling Certificates
- Configuring your RADIUS servers for SM authentication
- Assigning SM management IP addressing via RADIUS
- Configuring your RADIUS server for SM configuration
- Using RADIUS for centralized AP and SM user name and password management
- RADIUS Device Data Accounting
- RADIUS Device Re-authentication
Task 15: Configuring a RADIUS server PMP 450i and PTP 450i Configuration and User
Guide
Beginning with System Release 12.0.2, two RADIUS dictionary files are available
on the Cambium website – “RADIUS Dictionary file – Cambium” and “RADIUS
Dictionary file – Motorola”.
In addition to a renaming of attributes, the Cambium-branded dictionary file
contains two new VSAs for controlling uplink and downlink Maximum Burst Data
Rate (these VSAs are listed below in Table 60).
If you are transitioning from the Motorola-branded dictionary file to the Cambium-
branded dictionary file, ensure that all RADIUS profiles containing Motorola-
Canopy attribute references are updated to include Cambium-Canopy attribute
references (for all applicable VSAs listed in Table 60). Also, ensure that all
RADIUS configuration files reference the new dictionary file (as an alternative,
operators may rename the Cambium-branded dictionary file to the filename
currently in use by the RADIUS server). Once the profiles are updated and the new
Cambium-branded dictionary file is installed on the RADIUS server, restart the
RADIUS server to ensure that the new VSAs and attribute names are enabled.
Table 60 RADIUS Vendor Specific Attributes (VSAs)
N
ame
N
umber
T
ype
R
eq’d
V
alue
S
M GUI Page > Tab >
Parameter
D
efault
Si
ze
MS-MPPE-Send-Key
1
26.311.16
-
Y
-
-
-
-
MS-MPPE-Recv-Key
2
26.311.17
-
Y
-
-
-
-
Cambium-Canopy-LPULCIR
26.161.1
intege
N
0-65535
kbps
Configuration > Quality of Service > Low Priority
0
kbps
32
bits
Cambium-Canopy-LPDLCIR
26.161.2
intege
N
0-65535
kbps
Configuration > Quality of Service > Low Priority
0
kbps
32
bits
Cambium-Canopy-HPULCIR
26.161.3
intege
N
0-65535
kbps
Configuration > Quality of Service > Hi Priority Uplink
0
kbps
32
bits
Cambium-Canopy-HPDLCIR
26.161.4
intege
N
0-65535
kbps
Configuration > Quality of Service > Hi Priority Uplink
0
kbps
32
bits
Cambium-Canopy-
26.161.5
intege
N
0-disable,
1-enable
Configuration > Quality of Service > Hi Priority
0
32
bits
1
Contains key for encrypting packets sent by the NAS to the remote host (for Microsoft
Point-to-Point Encryption Protocol)
2
Contains key for encrypting packets received by the NAS from the remote host (for
Microsoft Point-to-Point Encryption Protocol)
pmp-0957 (April 2015) 201