Installation Guide
Table Of Contents
- PMP 450i and PTP 450i Configuration and User Guide
- Safety and regulatory information
- Contents
- List of Figures
- List of Tables
- About This Configuration and User Guide
- Chapter 1: Reference information
- Chapter 2: Configuration
- Preparing for configuration
- Task 1: Connecting to the unit
- Task 2: Configuring IP and Ethernet interfaces
- Configuring the AP IP interface
- NAT, DHCP Server, DHCP Client and DMZ in SM
- Configuring the SM IP interface with NAT disabled
- Configuring the SM IP interface with NAT enabled
- NAT tab of the SM with NAT disabled
- NAT tab of the SM with NAT enabled
- Reconnecting to the management PC
- VLAN Remarking and Priority bits configuration
- VLAN tab of the AP
- VLAN tab of the SM
- VLAN Membership tab of the SM
- PPPoE tab of the SM
- NAT Port Mapping tab of the SM
- Task 3: Upgrading the software version and using CNUT
- Task 4: Configuring General and Unit settings
- Task 5: Configuring security
- Isolating APs from the internet
- Encrypting radio transmissions
- Managing module access by passwords
- Requiring SM Authentication
- Filtering protocols and ports
- Encrypting downlink broadcasts
- Isolating SMs
- Filtering management through Ethernet
- Allowing management only from specified IP addresses
- Configuring management IP by DHCP
- Restricting radio Telnet access over the RF interface
- Security tab of the AP
- Filtering protocols and ports
- Protocol Filtering tab of the AP
- Port configuration tab of the AP
- Security tab of the SM
- Protocol Filtering tab of the SM
- Port Configuration tab of the SM
- Task 6: Configuring radio parameters
- Task 7: Setting up SNMP agent
- Task 8: Configuring syslog
- Task 9: Configuring remote access
- Task 10: Monitoring the AP-SM Link
- Task 11: Configuring quality of service
- Maximum Information Rate (MIR) Parameters
- Token Bucket Algorithm
- MIR Data Entry Checking
- Committed Information Rate (CIR)
- Bandwidth from the SM Perspective
- Interaction of Burst Allocation and Sustained Data Rate Settings
- High-priority Bandwidth
- Traffic Scheduling
- Setting the Configuration Source
- Quality of Service (QoS) tab of the AP
- DiffServ tab of the AP
- Quality of Service (QoS) tab of the SM
- DiffServ tab of the SM
- Task 12: Performing an Sector Wide SA
- Task 13: Zero Touch Configuration Using DHCP Option 66
- Task 14: Configuring Radio via config file
- Task 15: Configuring a RADIUS server
- Understanding RADIUS for PMP 450i
- Choosing Authentication Mode and Configuring for Authentication Servers - AP
- SM Authentication Mode – Require RADIUS or Follow AP
- Handling Certificates
- Configuring your RADIUS servers for SM authentication
- Assigning SM management IP addressing via RADIUS
- Configuring your RADIUS server for SM configuration
- Using RADIUS for centralized AP and SM user name and password management
- RADIUS Device Data Accounting
- RADIUS Device Re-authentication
Task 6: Configuring radio parameters PMP 450i and PTP 450i Configuration and User
Guide
Table 41 Adjacent Channel Interference (ACI) per MCS, PMP/PTP 450i
MCS of Victim MCS of Interferer Channel BW ACI
Guard
Band
1X (QPSK SISO) 6X (64-QAM MIMO-B)
5, 7, 10 or 20 MHz
-16 dB
None
2X (16-QAM SISO) 6X (64-QAM MIMO-B)
5, 7, 10 or 20 MHz
-16 dB
None
3X (64-QAM SISO) 6X (64-QAM MIMO-B)
5, 7, 10 or 20 MHz
-16 dB
None
1X (QPSK MIMO-A)
6X (64-QAM MIMO-B)
5, 7, 10 or 20 MHz
-13 dB
None
2X (16-QAM MIMO-
A)
6X (64-QAM MIMO-B)
5, 7, 10 or 20 MHz
-13 dB
None
3X (64-QAM MIMO-
A)
6X (64-QAM MIMO-B)
5, 7, 10 or 20 MHz
-13 dB
None
4X (256-QAM MIMO-
A)
6X (64-QAM MIMO-B)
5, 7, 10 or 20 MHz
-10 dB
None
2X (QPSK MIMO-B)
6X (64-QAM MIMO-B)
5, 7, 10 or 20 MHz
-16 dB
None
4X (16-QAM MIMO-
B)
6X (64-QAM MIMO-B)
5, 7, 10 or 20 MHz
-16 dB
None
6X (64-QAM MIMO-
B)
6X (64-QAM MIMO-B)
5, 7, 10 or 20 MHz
-16 dB
None
8X (256-QAM MIMO-
B)
6X (64-QAM MIMO-B)
5, 7, 10 or 20 MHz
-10 dB
None
No Guard Bands are needed for the 5.8 GHz bands.
pmp-0957 (April 2015) 131