Installation Guide
Table Of Contents
- PMP 450i and PTP 450i Configuration and User Guide
- Safety and regulatory information
- Contents
- List of Figures
- List of Tables
- About This Configuration and User Guide
- Chapter 1: Reference information
- Chapter 2: Configuration
- Preparing for configuration
- Task 1: Connecting to the unit
- Task 2: Configuring IP and Ethernet interfaces
- Configuring the AP IP interface
- NAT, DHCP Server, DHCP Client and DMZ in SM
- Configuring the SM IP interface with NAT disabled
- Configuring the SM IP interface with NAT enabled
- NAT tab of the SM with NAT disabled
- NAT tab of the SM with NAT enabled
- Reconnecting to the management PC
- VLAN Remarking and Priority bits configuration
- VLAN tab of the AP
- VLAN tab of the SM
- VLAN Membership tab of the SM
- PPPoE tab of the SM
- NAT Port Mapping tab of the SM
- Task 3: Upgrading the software version and using CNUT
- Task 4: Configuring General and Unit settings
- Task 5: Configuring security
- Isolating APs from the internet
- Encrypting radio transmissions
- Managing module access by passwords
- Requiring SM Authentication
- Filtering protocols and ports
- Encrypting downlink broadcasts
- Isolating SMs
- Filtering management through Ethernet
- Allowing management only from specified IP addresses
- Configuring management IP by DHCP
- Restricting radio Telnet access over the RF interface
- Security tab of the AP
- Filtering protocols and ports
- Protocol Filtering tab of the AP
- Port configuration tab of the AP
- Security tab of the SM
- Protocol Filtering tab of the SM
- Port Configuration tab of the SM
- Task 6: Configuring radio parameters
- Task 7: Setting up SNMP agent
- Task 8: Configuring syslog
- Task 9: Configuring remote access
- Task 10: Monitoring the AP-SM Link
- Task 11: Configuring quality of service
- Maximum Information Rate (MIR) Parameters
- Token Bucket Algorithm
- MIR Data Entry Checking
- Committed Information Rate (CIR)
- Bandwidth from the SM Perspective
- Interaction of Burst Allocation and Sustained Data Rate Settings
- High-priority Bandwidth
- Traffic Scheduling
- Setting the Configuration Source
- Quality of Service (QoS) tab of the AP
- DiffServ tab of the AP
- Quality of Service (QoS) tab of the SM
- DiffServ tab of the SM
- Task 12: Performing an Sector Wide SA
- Task 13: Zero Touch Configuration Using DHCP Option 66
- Task 14: Configuring Radio via config file
- Task 15: Configuring a RADIUS server
- Understanding RADIUS for PMP 450i
- Choosing Authentication Mode and Configuring for Authentication Servers - AP
- SM Authentication Mode – Require RADIUS or Follow AP
- Handling Certificates
- Configuring your RADIUS servers for SM authentication
- Assigning SM management IP addressing via RADIUS
- Configuring your RADIUS server for SM configuration
- Using RADIUS for centralized AP and SM user name and password management
- RADIUS Device Data Accounting
- RADIUS Device Re-authentication
List of Tables PMP 450i and PTP 450i Configuration and User
Guide
Table 39 PMP 450i Modulation levels ........................................................................... 130
Table 40 Co-channel Interference per (CCI) MCS, PMP/PTP 450i ............................... 130
Table 41 Adjacent Channel Interference (ACI) per MCS, PMP/PTP 450i .................... 131
Table 42 AP SNMP attributes ........................................................................................ 136
Table 43 SM SNMP attributes ....................................................................................... 141
Table 44 Syslog enhancements...................................................................................... 144
Table 45 AP Syslog Configuration attributes ................................................................ 145
Table 46 Syslog Configuration attributes ...................................................................... 146
Table 47 SM IP Configuration attributes ...................................................................... 148
Table 48 Characteristics of traffic scheduling .............................................................. 158
Table 49 Recommended combined settings for typical operations .............................. 159
Table 50 Where feature values are obtained for a SM with authentication required . 160
Table 51 Where feature values are obtained for a SM with authentication disabled .. 160
Table 52 AP QoS attributes ............................................................................................ 161
Table 53 AP Diffserv attributes ..................................................................................... 164
Table 54 SM Quality of Service attributes .................................................................... 165
Table 55 SM DiffServ attributes .................................................................................... 168
Table 56 Spectrum Analyzer attributes ........................................................................ 173
Table 57 Remote Spectrum Analyzer tab attributes ..................................................... 175
Table 58 Security tab attributes .................................................................................... 187
Table 59 SM Security tab attributes ............................................................................. 193
Table 60 RADIUS Vendor Specific Attributes (VSAs) ................................................... 201
Table 61 AP User Authentication and Access Tracking attributes ............................... 205
Table 62 SM User Authentication and Access Tracking attributes .............................. 207
Table 63 Device data accounting RADIUS attributes ................................................... 208
Table 64 Glossary ........................................................................................................... 213
Table 65 FCC and IC approved antennas list .............................................................. 227
xiv pmp-0957 (April 2015)