Installation Guide
Table Of Contents
- PMP 450i and PTP 450i Configuration and User Guide
- Safety and regulatory information
- Contents
- List of Figures
- List of Tables
- About This Configuration and User Guide
- Chapter 1: Reference information
- Chapter 2: Configuration
- Preparing for configuration
- Task 1: Connecting to the unit
- Task 2: Configuring IP and Ethernet interfaces
- Configuring the AP IP interface
- NAT, DHCP Server, DHCP Client and DMZ in SM
- Configuring the SM IP interface with NAT disabled
- Configuring the SM IP interface with NAT enabled
- NAT tab of the SM with NAT disabled
- NAT tab of the SM with NAT enabled
- Reconnecting to the management PC
- VLAN Remarking and Priority bits configuration
- VLAN tab of the AP
- VLAN tab of the SM
- VLAN Membership tab of the SM
- PPPoE tab of the SM
- NAT Port Mapping tab of the SM
- Task 3: Upgrading the software version and using CNUT
- Task 4: Configuring General and Unit settings
- Task 5: Configuring security
- Isolating APs from the internet
- Encrypting radio transmissions
- Managing module access by passwords
- Requiring SM Authentication
- Filtering protocols and ports
- Encrypting downlink broadcasts
- Isolating SMs
- Filtering management through Ethernet
- Allowing management only from specified IP addresses
- Configuring management IP by DHCP
- Restricting radio Telnet access over the RF interface
- Security tab of the AP
- Filtering protocols and ports
- Protocol Filtering tab of the AP
- Port configuration tab of the AP
- Security tab of the SM
- Protocol Filtering tab of the SM
- Port Configuration tab of the SM
- Task 6: Configuring radio parameters
- Task 7: Setting up SNMP agent
- Task 8: Configuring syslog
- Task 9: Configuring remote access
- Task 10: Monitoring the AP-SM Link
- Task 11: Configuring quality of service
- Maximum Information Rate (MIR) Parameters
- Token Bucket Algorithm
- MIR Data Entry Checking
- Committed Information Rate (CIR)
- Bandwidth from the SM Perspective
- Interaction of Burst Allocation and Sustained Data Rate Settings
- High-priority Bandwidth
- Traffic Scheduling
- Setting the Configuration Source
- Quality of Service (QoS) tab of the AP
- DiffServ tab of the AP
- Quality of Service (QoS) tab of the SM
- DiffServ tab of the SM
- Task 12: Performing an Sector Wide SA
- Task 13: Zero Touch Configuration Using DHCP Option 66
- Task 14: Configuring Radio via config file
- Task 15: Configuring a RADIUS server
- Understanding RADIUS for PMP 450i
- Choosing Authentication Mode and Configuring for Authentication Servers - AP
- SM Authentication Mode – Require RADIUS or Follow AP
- Handling Certificates
- Configuring your RADIUS servers for SM authentication
- Assigning SM management IP addressing via RADIUS
- Configuring your RADIUS server for SM configuration
- Using RADIUS for centralized AP and SM user name and password management
- RADIUS Device Data Accounting
- RADIUS Device Re-authentication
List of Figures
Figure 1 AP DFS Status ............................................................................................................ 8
Figure 2 AP General Status page, GUEST user example ....................................................... 16
Figure 3 SM General Status page, GUEST user example ...................................................... 16
Figure 4 AP General Status page, ADMINISTRATOR user example ..................................... 17
Figure 5 SM General Status page, ADMINISTRATOR user example .................................... 18
Figure 6 NAT disabled implementation .................................................................................. 23
Figure 7 NAT with DHCP client and DHCP server implementation ...................................... 23
Figure 8 NAT with DHCP client implementation ................................................................... 24
Figure 9 NAT with DHCP server implementation .................................................................. 24
Figure 10 NAT without DHCP implementation ...................................................................... 25
Figure 11 IP tab of the SM with NAT disabled ...................................................................... 26
Figure 12 IP tab of SM ............................................................................................................ 26
Figure 13 IP tab of SM with NAT enabled ............................................................................. 29
Figure 14 SM with NAT disabled ........................................................................................... 30
Figure 15 NAT tab of the SM with NAT enabled ................................................................... 34
Figure 16 VLAN tab of the AP ................................................................................................ 43
Figure 17 VLAN tab of the SM ............................................................................................... 46
Figure 18 VLAN Membership tab of the SM .......................................................................... 51
Figure 19 PPPoE tab of the SM .............................................................................................. 51
Figure 20 NAT Port Mapping tab of the SM .......................................................................... 55
Figure 21 General tab ............................................................................................................. 61
Figure 22 Unit Settings tab of the AP ................................................................................... 68
Figure 23 General tab of the SM ............................................................................................ 71
Figure 24 Unit Settings tab of the SM ................................................................................... 74
Figure 25 Time tab of the AP .................................................................................................. 76
Figure 26 AP / SM Add User tab of account page .................................................................. 81
Figure 27 Delete User tab of the AP / SM .............................................................................. 81
Figure 28 Change User Setting tab AP / SM .......................................................................... 82
Figure 29 AP Evaluation Configuration parameter of Security tab ....................................... 82
Figure 30 RJ-11 pin out for the override plug ........................................................................ 83
Figure 31 Categorical protocol filtering ................................................................................. 86
Figure 32 RF Telnet Access Restrictions (orange) and Flow through (green) ...................... 90
Figure 33 RF Telnet Access Restriction (orange) and Potential Security Hole (green) ....... 90
Figure 34 Security tab of the AP ............................................................................................ 93
Figure 35 Protocol Filtering tab of the AP ............................................................................. 97
Figure 36 Port Configuration tab of the AP .......................................................................... 99
Figure 37 Security tab of the SM ........................................................................................ 100
Figure 38 Protocol Filtering tab of the SM .......................................................................... 106
Figure 39 Port Configuration tab of the SM ........................................................................ 108
Figure 40 Radio tab of the AP for 5 GHz .............................................................................. 109