User's Manual

ManualsBrandsCambium Networks ManualsElectronicsWireless Ethernet Bridge

Table Of Contents

1 About This User Guide
- 1.1 Interpreting Typeface and Other Conventions
- 1.2 Getting Additional Help
- 1.3 Sending Feedback
2 Avoiding Hazards
- 2.1 Preventing Overexposure to RF Energy
  - 2.1.1 Calculations for Separation Distances and Power Compliance Margins
    - 2.1.1.1 Calculated Distances and Power Compliance Margins
Getting Started
- For Your Safety
- 3.2 Welcome
- 3.3 Product Description
- 3.4 Warranty
4 Product Architecture
5 General Considerations
- 5.1 Spectrum Planning
- 5.2 Introducing the Time Division Duplex (TDD) Synchronization Feature
- 5.3 Region Codes
- 5.4 Operational Restrictions
- 5.5 2.5GHz Specific Frequency Planning Considerations
  - 5.5.1 Variable Channel Bandwidth Operation
  - 5.5.2 Power Reduction in the Upper Band
- 5.6 5.4GHz Specific Frequency Planning Considerations
  - 5.6.1 Raster Considerations
  - 5.6.2 Transmit Power Reduction at the Band Edges
- 5.7 5.8GHz Specific Frequency Planning Considerations
  - 5.7.1 Raster Considerations
  - 5.7.2 Transmit Power Reduction at the Band Edges
- 5.8 Distance
- 5.9 Networking Information
- 5.10 Lightning Protection
- 5.11 Electrical Requirements
6 Site Planning
- 6.1 Site Selection Criteria
7 Installation
- 7.1 Preparation
- 7.2 Installation Procedure
- 7.3 Tools Required
- 7.4 Installation Support
- 7.5 Legal Disclaimer
- 7.6 Mounting the ODUs
- 7.7 Connecting Up
8 Web Page Reference
- 8.1 Home Page – PTP 600 Series Bridge
  - 8.1.1 Home Page Alarm Display
- 8.2 Systems Status Page
- 8.3 System Administration Pages
9 Recovery Mode
- 9.1 Upgrade Software Image
- 9.2 Reset IP & Ethernet Configuration
- 9.3 Erase Configuration
- 9.4 Reboot
10 Fault Finding
- 10.1 Hardware
- 10.2 Radio
  - 10.2.1 No Activity
  - 10.2.2 Some Activity
11 Lightning Protection
- 11.1 Overview
  - 11.1.1 Lightning Protection Zones
- 11.2 Detailed Installation
- 11.3 Testing Your Installation
  - 11.3.1 Pre-Power Testing
  - 11.3.2 Post-Power Testing
12 Wind Loading
- 12.1 General
- 12.2 Calculation of Lateral Force
- 12.3 Capabilities of the PTP 600 Series Bridges
- 12.4 Wind Speed Statistics
13 PTP 600 Series Bridge – Connectorized Model
- 13.1 Scope
- 13.2 Product Description
  - 13.2.1 Hardware
  - 13.2.2 Antenna Choices – 5.8 GHz
- 13.3 Software/Features
- 13.4 Deployment Considerations
- 13.5 Link Budget
- 13.6 Regulatory Issues
  - 13.6.1 Antenna Choice (FCC Regions Only)
  - 13.6.2 Cable Losses (FCC Regions Only)
- 13.7 Antennas for USA / Canada
- 13.8 Installation
- 13.9 Additional Lightning Protection
  - 13.9.1 ODU Mounted Outdoors
  - 13.9.2 ODU Mounted Indoors
14 TDD Synchronization Configuration and Installation Guide
- 14.1 Introduction
- 14.2 TDD Synchronization Installation and Wiring Guidelines
  - 14.2.1 Installing the Recommended GPS Synchronization Kit
- 14.3 Configuring the TDD Synchronization Feature
  - 14.3.1 TDD Synchronization Enable
  - 14.3.2 TDD Synchronization Configuration Menu
    - 14.3.2.1 TDD Synchronization Configuration – Expert Mode
    - 14.3.2.2 Confirm Settings and Reboot ODU
15 E1/T1 Installation Guide
- 15.1 Preparing the PTP 600 Series Bridge E1/T1 Cable
- 15.2 Making the Connection at the ODU
- 15.3 Routing the Cable
- 15.4 Fitting a Surge Arrestor
- 15.5 Customer Cable Termination
16 Lightning Protection
- 16.1 Overview
- 16.2 Recommended Additional Components for E1/T1 Installation.
- 16.3 Surge Arrestor Wiring
- 16.4 Testing Your Installation
  - 16.4.1 Pre-Power Testing
17 Data Rate Calculations
18 AES Encryption Upgrade
- 18.1 Configuring Link Encryption
- 18.2 Configuring Link Encryption
  - 18.2.1 License Keys
  - 18.2.2 Encryption Mode and Key
- 18.3 Wireless Link Encryption FAQ
19 Legal and Regulatory Notices
- 19.1 Important Note on Modifications
- 19.2 National and Regional Regulatory Notices – 5.8 GHz variant
- 19.3 National and Regional Regulatory Notices – 5.4 GHz Variant
  - 19.3.1 U.S. Federal Communication Commission (FCC) and Industry Canada (IC) Notification
  - 19.3.2 European Union Notification
- 19.4 National and Regional Regulatory Notices – 2.5 GHz Variant
  - 19.4.1 U.S. Federal Communication Commission (FCC) Notification
- 19.5 Exposure
- 19.6 Legal Notices
20 Glossary
21 FAQs
22 Index Alar
- 23.1 System Specifications
- 23.2 Safety Compliance
- 23.3 EMC Emissions Compliance
- 23.4 EMC Immunity Compliance
- 23.5 Radio Certifications
- 23.6 Environmental Specifications
- 23.7 System Connections
  - 23.7.1 PIDU Plus to ODU and ODU to Network Equipment Connections

7.7.2 Making the Connections at the ODU

Looking at the back of the unit with the cable entry at the bottom, the PTP 600 Series Bridge

PIDU Plus connection is the first hole on the right (

1034HFigure 31) and is labeled “PIDU +”.

Figure 31 – PTP 600 Series Bridge PIDU Plus Connection