Install Drawing

Model 8050
Horsepower ................. 1.5
Shaft Diameter............. 5/8"
Max. Volts.................... 115/230
FULL LOAD AMPS...... 12.1
RPM............................. 3450
Weight ......................... 32.1 lbs.
Phase .......................... Single
Frame Size .................. 56-C TEFC
Service Factor ............. 1.15
Model 8052
Horsepower ................. 2.0
Shaft Diameter............. 5/8"
Max. Volts.................... 115/230
FULL LOAD AMPS...... 17.0/9.2-8.5
RPM............................. 3450
Weight ......................... 32.5 lbs.
Phase .......................... Single
Frame Size .................. 56-C TEFC
Hertz............................ 60
Service Factor ............. 1.15
Model 8055
Horsepower ................. 3.0
Shaft Diameter.............
● 3/4"
Max. Volts.................... 208/230
FULL LOAD AMPS...... 15 2/13.6
RPM............................. 3450
Weight ......................... 46.3 lbs.
Phase .......................... Single
Frame Size .................. 56-C TEFC
Service Factor ............. 1.15
●
Use 3/4" shaft size motor with GES Pumps.
Model 8057
Horsepower ................. 5.0
Shaft Diameter.............
● 3/4"
Max. Volts.................... 230
FULL LOAD AMPS...... 22.0
RPM............................. 3450
Weight ......................... 40 lbs.
Phase .......................... Single
Frame Size .................. 56-C OPEN DRIP
Service Factor ............. 1.15
●
Use 3/4" shaft size motor with GES Pumps.
★
Model 8060
Horsepower ................. 1.5
Shaft Diameter............. 5/8"
Max. Volts.................... 115/230
FULL LOAD AMPS...... 14.0/7.0
RPM............................. 1725
Weight ......................... 40 lbs.
Phase .......................... Single
Frame Size .................. 56-C TEFC
Service Factor ............. 1.2
★
Use with ELS models or to reduce flow by
50% on standard models.
★
Model 8062
Horsepower ................. 2.0
Shaft Diameter............. 5/8"
Max. Volts.................... 115/230
FULL LOAD AMPS...... 17.0/8.5
RPM............................. 1725
Weight ......................... 43.7 lbs.
Phase .......................... Single
Frame Size .................. 56-C TEFC
Service Factor ............. 1.15
★
Use with ELS models or to reduce flow by
50% on standard models.
Common Motor Specifications
Max. Operating Temp................. 104°F
Capacitor Start ........................... Yes
Thermal Overload-Manual Reset Yes
U.L. Construction Reference
(8050,8055)................................. E49747
(8052, 8057, 8060, 8062) ............ E44549
U.L. Insulation Reference (All) ... E37878
CSA Reference
(8050) ......................................... LR45148
(8052, 8057, 8060, 8062)........... LR4642
(8055) ......................................... LR2025
Note Motor Start-Up AMPS may vary, then settle
within FULL LOAD AMPS rating after initial
run in time.
★★
Before mounting pump on motor, apply P.N.
6106 Antiseize Lubricant to pump shaft.
★★
Refer to Tech Bulletin #55 for instructions on
removing pump from gas engine or electric
motor.
Add .50 for 50 Hz (1450 or 2850 RPM)
For warranty consideration contact CAT PUMPS for the local Authorized Service Center. If you are uncertain as to he cause of failure (Pump or Motor),
secure Returned Goods Authorization number and return complete assembly PREPAID to CAT PUMPS for evaluation.
MOTOR SPECIFICATIONS
DETERMINING THE REQUIRED H.P.
GPM x PSI Electric Brake
1460 H.P. Required
=
DIMENSIONAL DRAWING
★ Dual Capacitor on top and front side electrical box
HORSEPOWER REQUIREMENTS
FLOW PRESSURE PUMP
PSI PSI PSI PSI PSI RPM
700 1000 1200 1500 2000
U.S. Metric BAR BAR BAR BAR BAR
GPM L/M 50 70 85 105 140
1.0 3.8 .44 .69 .82 1.0 1.4 3450
2.2 8.3 1.1 1.5 1.8 2.3 3.0 3450
2.85 10.8 1.4 2.0 2.3 2.9 N/A 1725
3.0 11.4 1.4 2.1 2.5 3.1 4.2 3450
3.5 13.2 1.7 2.4 2.9 3.6 N/A 3450
Products described hereon are covered by one or more of the following U.S. patents 3558244, 3652188, 3809508, 3920356, 3930756 and 5035580
CAT PUMPS (U.K.) LTD.
1 Fleet Business Park, Sandy Lane, Church Crookham, Fleet
Hampshire GU13 OBF, England
Phone Fleet 44 1252-622031 — Fax [phone]
N.V. CAT PUMPS INTERNATIONAL S.A.
Heiveldekens 6A, 2550 Kontich, Belgium
Phone [phone] — Fax [phone]
e-mail: cpi@catpumps be www catpumps.be
CAT PUMPS DEUTSCHLAND GmbH
Buchwiese 2, D-65510 Idstein, Germany
Phone [phone] — Fax [phone]
e-mail: [e-mail] www.catpumps de
World Headquarters
CAT PUMPS
1681 - 94th Lane N.E. Minneapolis, MN 55449-4324
Phone [phone] — FAX [phone]
e-mail: [e-mail]
www.catpumps.com
International Inquiries
FAX [phone]
e-mail: [e-mail]
“The World’s Most Dependable Pumps”
Oct 2000 9016