User manual

Compliance Test System 3.0 User Manual
List of Figures
Figure 3-1: EUT Connection distance and wire gauge................................................................... 32
Figure 3-2: Functional Test Setup ..................................................................................................34
Figure 3-3: Single-phase configuration 5001iX-CTS...................................................................... 35
Figure 3-4: Single-phase configuration 1251RP-CTS....................................................................36
Figure 3-5: Power Connections for PACS-1 for a single-phase CTS............................................. 37
Figure 3-6: Three-phase configuration 15003iX-CTS .................................................................... 38
Figure 3-7: Power Connections for PACS-3 in a three-phase CTS. .............................................. 39
Figure 3-8: Switch Settings for Remote Impedance Control (Factory Default) .............................. 41
Figure 3-9: Switch Settings for Manual Impedance Control........................................................... 41
Figure 3-10: Front and Rear Panel Views of the PACS-1 Module. ................................................ 42
Figure 3-11: Front and Rear Panel Views of the PACS-3 Module. ................................................ 43
Figure 3-12: Exacq Control Center Screen. ................................................................................... 48
Figure 3-13: Exacq Card Device Number....................................................................................... 49
Figure 3-14: Exacq Test Panel ....................................................................................................... 50
Figure 3-15: Exacq DMM Screen ...................................................................................................51
Figure 3-16: Exacq Scope Test Panel............................................................................................ 52
Figure 3-17: NI E Series Explorer Panel ........................................................................................53
Figure 3-18: Figure 318: NI M Series Explorer Panel.................................................................. 53
Figure 3-19: Jumper and DIP switch location on the A/D Card...................................................... 56
Figure 3-20: A/D Card JMP 11 Settings ......................................................................................... 57
Figure 3-21: A/D Card JMP 13 Settings ......................................................................................... 57
Figure 3-22: A/D Card Base I/O Address DIP ................................................................................ 59
Figure 5-1: Class D Current Wave Shape Template...................................................................... 71
Figure 5-2: EUT Class Determination Flowchart............................................................................ 72
Figure 5-3: Typical Class A test setup............................................................................................ 74
Figure 5-4: Additonal Settings for Harmonics Test......................................................................... 76
Figure 5-5: Harmonics Test Window .............................................................................................. 78
Figure 6-1: Flicker Test Window.....................................................................................................87
Figure 7-1: IEC 61000-4-11 Test Window......................................................................................95
Figure 7-2: IEC 61000-4-11 Voltage Variation specification- Edition 1.0....................................... 96
Figure 7-3: IEC 61000-4-11 Voltage Variation specification- Edition 2.0....................................... 96
Figure 7-4: IEC 61000-4-11 Setup screen...................................................................................... 98
Figure 8-1: IEC 61000-4-13 Test Window....................................................................................101
Figure 8-2: IEC 61000-4-13 Flow Chart Class 1 and 2. ............................................................... 104
Figure 8-3: IEC 61000-4-13 Flow Chart Class 3. .........................................................................105
Figure 9-1: IEC 61000-4-14 Test Window....................................................................................109
Figure 9-2: IEC 61000-4-14 Test Sequence................................................................................. 111
Figure 10-1: IEC 61000-4-17 Test Window.................................................................................. 116
Figure 10-2: IEC 61000-4-17 Waveform Acquisition Window...................................................... 118
Figure 10-3: IEC 61000-4-17 User Observation Data Entry Window........................................... 119
Figure 11-1: IEC 61000-4-27 Test Window.................................................................................. 120
Figure 12-1: IEC 61000-4-28 Test Window.................................................................................. 127
Figure 12-2: IEC 61000-4-28 Test Sequence .............................................................................. 129
Figure 13-1: IEC 61000-4-29 Test Window.................................................................................. 132
Figure 17-1 : CTS 3.0 Calibration Program Main Screen............................................................. 153
Figure 17-2: Single Phase Calibration Setup ............................................................................... 155
Figure 17-3: Three Phase Calibration Setup................................................................................ 156
Figure 19-1: Location of AC Sensor Assy. 5004-700 in PACS-x ................................................. 162
10 Revision N California Instruments