ULTRA QUieT, ULTRA dRy & OiL FRee AiR COMPReSSOR OwneR'S MAnUAL CALiFORniA AiR TOOLS 20040dSPCAdC 4.0 HP 20 gALLOn 220 vOLTS 60 HeRTz AiR dRying SySTeM AUTOMATiC dRAin vALve SOUndPROOF CAbineT WWW.CALIFORNIAAIRTOOLS.
AiR COMPReSSOR TAbLe OF CONTeNTS INTROduCTION IntroductIon __________________________________2 Important Safety InStructIonS _______________5 aIr compreSSor componentS__________________7 pre-operatIon checklISt ______________________8 package contents & assembly____________________8 Inspect for damage _____________________________8 Save packaging ________________________________8 compressor location ___________________________8 electrical power ________________________________9 operatIng the aIr compreSS
AiR COMPReSSOR how to find a local service center: even quality built equipment might need service or repair parts. Contact the California Air Tools Customer Service department: Phone: 1-866-409-4581 Online: WOWed.CALIFORNIAAIRTOOLS.COM please provide the information below: Model number and Serial number and specifications shown on the Model number/Serial number plate. Part number or numbers shown in the parts list section of the owner’s manual for your air compressor model.
AiR COMPReSSOR WARNING WARNING FLYING OBJECTS RISK TO BREATHING Dust or dust-like particulates caused by power-sanding, sawing, grinding, drilling or any other construction-like activities can contain contaminants that are harmful to breathe. Always use your air compressor in a well-ventilated and clean area. Never breathe the air that comes directly out of the air compressor or air hose. This air is not suitable for breathing. Always wear approved safety equipment.
AiR COMPReSSOR WARNING WARNING EXPLOSION EXPLOSION Improper care could lead to the air tank bursting or exploding. Drain air tank daily or after each use to prevent moisture buildup in the air tank. Rust can weaken the air tank and cause leaks or bursting. If rust is detected, replace tank immediately. Do not try to repair the air tank by welding, drilling or modifying it in any other way. These modifications can weaken the air tank and cause a hazardous condition.
AiR COMPReSSOR LOCATIONS OF IMPORTANT LAbeLS PROduCT LAbeL a Read these important labels before operating. These labels provide important safety and maintenance information. These labels should be considered as permanent parts of the air compressor. Should any of these labels become illegible, damaged or removed, please contact California Air Tools Customer Service department at 1-866-409-4581 for replacements.
AiR COMPReSSOR Customer Support: 1-866-409-4581 7
AiR COMPReSSOR pre-operatIon checklISt Inspect for damage package contents before using the air compressor, make sure the air tank is not damaged, inspect all parts for damage, and check that all pipes are firmly connected. model: 20040dSpcadc do not use the air compressor if any damage is found. If damaged, have an authorized service center inspect and test the air compressor to ensure that is working properly.
AiR COMPReSSOR electrical power electrical extension cord electrical power requirements Inspect all electrical extension cords to ensure that they are free of DANGER SHOCK There is a danger of electric shock. Use only undamaged electrical cords. DO NOT touch bare wires or receptacles. Inspect all electrical extension cords to ensure that they are free of damage. DO NOT operate air compressor in wet weather or in wet conditions.
AiR COMPReSSOR WARNING test run before using the air compressor for the first time, complete a test run as follows: 1. Turn the power switch to the OFF position. Plug the power supply cord into a power supply socket. Start the air compressor by turning the power switch to the ON position. The pressure gauge reading will slowly rise as pressure increases inside the air tank. When the gauge reading reaches 120 -125 PSI, the pressure switch will automatically turn the power off.
AiR COMPReSSOR MAINTeNANCe air drying canister - desiccant draining the air tank This air compressor includes an Air drying system. * Aftercooler (Condenser) The frequency at which you should drain the air tank depends on the environmental conditions and the amount of operating time logged. your air compressor is equiped with an eZ-1 Auto drain Valve that automatically drains the air tank. 1. Place the drain tube from the auto drain valve into a waste container capable of holding water. 2.
AiR COMPReSSOR TROubLeSHOOTINg proBlem Pressure drop in the tank. The unloader valve leaks when the compressor is idle. The compressor stopped and does not start. poSSIBle cauSe poSSIBle SolutIonS Air leaks at connections. Let the compressor build pressure in the tank, to the maximum pressure if possible. brush soapy water on air connections and look carefully for air bubbles. Tighten leaky connections. If the problem persists, contact the seller for further advice.
AiR COMPReSSOR SPeCIFICATIONS electrical circuit Pressure switch Electric cord for motor Overload protector (MAX temperature 135°C) Motor Red cords for Capacitor Solenoid valve Electric cord for motor Earth wire (Green) air passage drawing Air intake Pressure switch Drain valve Safety valve Pressure gauge Regulator Compressor Pressure gauge Tank Check valve Solenoid valve Filter Ball valve Customer Support: 1-866-409-4581 13
AiR COMPReSSOR CALIFORNIA AIR TOOLS INC. LIMITed WARRANTy This warranty is limited to Air Compressors distributed by: California Air Tools, Inc. 8560 Siempre Viva Road San diego, CA 92154 limited Warranty California Air Tools Inc. will repair or replace, free of charge, to the original retail customer who purchased a California Air Tools, Inc. Air Compressor from an authorized dealer, distributor or distributor’s dealer in North America. This warranty does not transfer to subsequent owners.
AiR COMPReSSOR exclusions In addition to the foregoing disclaimers, limitations and terms, this limited warranty shall not apply to and does not cover accessories, nor does it cover products that are in any way subject to any of the following: 1. Improper setup, installation or storage. 2. Lack of proper maintenance and service. 3. Accident, damage, abuse or misuse. 4. Abnormal operating conditions or applications. 5.
AiR COMPReSSOR PROduCT RegISTRATION To register your product, please complete the information below and mail to the mailing address at the end of this page. 1.
