Page CONTENTS 01 Contents 02 Installation 04 Using the detachable front panel 05 Wiring d iagram 06 Operations 06 Location and function of controls 07 General o perations 09 Radio o perations 10 RDS (Radio Data System) operations 11 CD/MP3 /WMA disc o perations 12 Mixed- mode CD o perations 13 USB o perations 13 SD/MMC c ard o perations 13 AUX in put o perations 14 Disc n otes 15 Trouble s hooting 16 Specifications
Installation Notes: Take Out Screw Before Installation Before install the unit, please remove the two screws. - Choose the mounting location where the unit will not interfere with the normal driving function of the driver. - Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. - Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.
6. Mount the sleeve by inserting the sleeve into the opening of the dashboard and bend open the tabs located around the sleeve with a screwdriver. Not all tabs will be able to make contact, so examine which ones will be most effective. Bending open the appropriate tabs behind the dashboard to secure the sleeve in place. 10. Reconnect the cable to the vehicle battery's negative (-) terminal. Then replace the outer trim ring and install the unit's front panel (see the steps of 'to install the front panel').
2. DIN REAR-MOUNT (Method B) If your vehicle is a Nissan, Toyota, follow this mounting instruction. Use the screw holes marked T (Toyota), N (Nissan) located on both sides of the unit to fasten the unit to the factory radio mounting brackets supplied with your vehicle. Using the detachable front panel Removing and protecting detachable front panel The front panel of the unit may be removed as a theft deterrent.
Wiring diagram RCA connector to front left output (White) RCA connector to rear left output (White) L R 15 FUSE 15A Antenna Socket RCA connector to rear right output (Red) ISO CONNECTOR RCA connector to front right output (Red) TO TEL.
Operations Location and function of controls Front panel: 18 1 2 19 29 6 4 RCD 264 7 TA AF/ REG 23 DISP PTY 8 MODE 20 5 ENT EQ 3 21 BND AMS 10 9 1 11 SCN RPT SHF - 10 + 10 2 3 4 5 6 12 13 16 17 14 15 AUX IN 22 The car radio after removing the front panel: 24 26 25 27 28 Descriptions of Function Controls (1) Power on/off Button ( ), Mute Button (2) Volume Control, Audio/Menu Selector (SEL) (3) Preset Equalizer (EQ) Button (4) LCD display (5) MODE Button (6) O
General Operations Reset the unit When operating the unit for the first time, after replacing the car battery or changing the connections, you must reset the unit. 1.Turn off the unit power. 2. Press the OPEN button ( ) to fold down the front panel and remove it, then press the RESET button with a ballpoint pen or similar object to restart the unit. Power on/off In power off mode, switch on the unit by pressing any button except the OPEN ( ) button.
“RETUNE L or RETUNE S” (long/short retune): This function allows you to set the duration after which the automatic search for traffic information or a station with an identical PI should be carried out. - RETUNE L mode: The automatic search will take place after 90 seconds. - RETUNE S mode: The automatic search will take place after 30 seconds.
CT -> FREQUENCY -> PTY NONE-> Radio operations In CDP/USB/SD mode: CT -> FREQUENCY -> PTY NONE -> Track or file number and Running time Note: The selected information is displayed for 5 seconds, then the radio goes back to the first display mode after 5 seconds. To select a radio band In radio mode, press the BAND button repeatedly to select a radio broadcasting band you would like to hear. The 3 FM bands will be changed cyclically through the tuning bands: ->FM 1-> FM 2 -> FM 3 ->.
Short pressing the AMS button, the radio searches for each preset station that saved in the memories of the current band. If the field strength level is more than the threshold level, the radio will hold at this preset station for 5 seconds with sound output, then go to next station, finally the radio will play at the preset station where scanning started. Press the AMS again to stop preset scanning. - Auto store: Press the AMS button for more than 2 seconds to start auto store.
Listening to Traffic Announcement It is possible to program the car radio so that it interrupts disc mode, radio mode, AUX mode or the current radio station when a traffic announcement is broadcast. Briefly press the TA button to switch TA mode on or off. When TA mode is on and a traffic announce -ment is transmitted: - When the car radio was in CD (MP3/WMA), USB/SD/MMC or AUX IN mode, it will switch temporarily to radio mode.
Repeat playback In CD or MP3/WMA file playback, briefly press the RPT button to continuously play the current track. The word “RPT” appears on the LCD display. Press again to stop repeat playback and resume normal playback. Shuffle playback In CD or MP3/WMA file playback, briefly press the SHF button to play all tracks or files in random sequence. The word “SHF” appears on the LCD display. Press again to cancel random playing.
USB operations The unit is equipped with a USB port on the front panel of the unit, you can connect a USB stick through the USB port. Using the USB stick: When you insert a USB stick through the port, the unit will search the MP3 files and start to play it automatically. If insert a disc into the disc slot while read the file in the USB device, the unit will playing the disc first. If you want to play the file in the USB device, press the MODE button to switch to USB mode.
Disc notes A. Notes on discs: 1. Attempting to use non-standard shape discs (e.g. square, start, and heart) may damage the unit. Be sure to use round shape CD discs only for this unit. 2. Do not stick paper or tape, etc, onto the label side or the recording side of any discs, as it may cause a malfunction. Dirty, dusty, scratched and warped discs will cause a malfunction. B. Notes on CD-Rs (recordable CDs)/CDRWs (rewritable CDs): 1. Be sure to use discs with following marks only for the unit to play: 2.
Trouble shooting The following chart will help in solving most problems that may occur. If you still have questions after going through the checklist, please consult your local customer service representative. Before going through this check list, refer the wiring and operating procedures. Symptom Cause The car ignition switch have not turn on. If the power supply is connected to the car accessory circuits, but the engine is not moving, switch the ignition key to “ACC”. The fuse has been blown.
Specifications 1. GENERAL Power Supply Requirements DC 12 Volts, Negative Ground Chassis Dimensions 178(W)x160(D)x 50(H) mm Tone Controls - Bass (at 100 Hz) - Treble (at 10 kHz) ±10 dB ±10 dB Maximum Output Power 4x75 watts Current Drain 15 Ampere (max.) 2. CD PLAYER Signal to Noise Ratio > 55 dB Channel Separation > 40 dB Frequency Response 20Hz - 20 KHz Discs/files played CD-DA,CD-R/RW/MP3/WMA 3. RADIO FM Frequency Coverage 87.5 - 108 . 0 Mhz IF 10.
W W W. C A L I B E R.NL Caliber Head Office • The Netherlands • Fax: +31 (0)416 69 90 01 • E-mail: info@caliber.
