INSTALLATION PRECAUTIONS • Choose the mounting location carefully so that the unit will not interfere with the normal driving functions of the driver. • Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight or hot air from the heater, or where it would be subject to dust, dirt or excessive vibration. • Use only the supplied mounting hardware for a safe and secure installation. • Be sure to remove the front panel before installing the unit.
TO SUPPORT THE UNIT 3 Dashboard 4 4 6 5 8 2 10 7 5 1 9 4 1. UNIT 2. RELEASE CASE 3. DASH BOARD 4. HEX NUT 5. LOCK WASHER 6. PLAIN WASHER 7. CAR BODY 8. REAR SUPPORT STRAP 9. TAPPING SCREW 10.
DRIVING WITH VIDEO DISPLAY By following the installation below, video will always be shown on LCD screen no matter the car is in motion or not. Steps: Connect the GRAY wire to the WHITE wire. INSTALLING REAR CAMERA FOR PARKING/REVERSE MOTION You can install an separate camera at the car rear end so when doing parking or reverse motion, the unit will automatically switch the video to the rear camera to guide the driver.
MCD 610 4x 75WATT Locations of Parts (Main unit) 1 2 7 9 12 11 10 4 13 14 1 2 6 7 22 9 MCD 610 12 AUX IN MCD 610 16 4x 75WATT MCD 610 17 15 3 (1-3) 1 2 7 4x 75WATT 8 9 18 12 1. POWER ON/OFF ( ) 2. SELECT FUNCTION BUTTON 3. PRESET STATIONS (1,2,3,4,5,6) 4. ‘AF’ function BUTTON (ALTERNATIVE FREQUENCIES) 5. ‘TA’ function BUTTON (TRAFFIC ANNOUNCEMENT) 6. ‘PTY’ function (PROGRAM TYPE) 7. LOUDNESS BUTTON (LD) 8. MODE BUTTON (MODE) MCD 610 21 9. BAND BUTTON (BD) 20 10.
Locations of Parts (Remote Control) 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31.
OPERATIONS Turning the unit ON/OFF ( ) Press “ ” button to turn on unit. To turn off, press the button again. Selecting a source (MODE) Press MODE repeatedly to switch between TUNER, AUX IN, USB or SD/MMC mode. Adjusting Volume • Head Unit: Rotate VOL knob right or left to increase or decrease volume. • Remote Control: Press VOL+ or VOL- to increase or decrease volume. Mute Button • Head Unit: Press MUTE button to mute the sound at once. Press again to return to previous volume level.
Storing and Recalling Frequencies If you press any of the NUMBER (1-6) you can easily store up to six broadcast frequencies for later recall with the touch of a button. 1. Choose a desired BAND. 2. When you find a frequency that you want to store in memory, press a NUMBER(1-6) and hold until the preset number shows and lit in the display. 3. The selected radio station frequency has been stored in memory. The next time you press the same NUMBER (1-6) the radio station frequency is recalled from memory.
A-B Repeat Playback This feature allows you to loop playback a section of the movie starting from Point A to B. 1. Press the button to play the movie. 2. Once you have located the section you wish to playback on loop repeat, press and hold A-B button. You will see “Rep-A” on the screen. 3. Let the movie play on until you have reached the end of the section you wish to watch on continuous loop. Once you have reached this point, press and hold A-B button again. “Rep-A-B” will appear on your screen.
Searching for particular track using GOTO You can use the GOTO function to search for a desired track number or particular point of a track to play. 1 Press GOTO on the remote control during playback. Time and track number search appears. 2 Enter the minutes and seconds for the currently played track if you want to search by time. Press Enter. 3 Enter track number if you want to search by tracks. Press Enter.
SETTING THE MPEG4 PLAYER You can flexibly customize the unit to suit your preference. You can set the language and other video and audio settings so when playback starts it will always use your preferred settings. Important: 1. Play any video file before you can access the setup. 2. Press Setup on the remote control. 3. Use ( / ) to return / enter category.
TECHNICAL SPECIFICATIONS MP3/WMA PLAYER SECTION Signal to Noise Ratio Channel Separation Frequency Response > 60 dB > 50 dB (1kHz) 20 Hz - 20 kHz TUNER (FM) Frequency Range Channel Step Sensitivity Stereo Separation Signal to Noise Ratio 87.5-108 MHz 50 kHz 2.8 µV 30 dB 50 dB LINE-OUT Output Impedance 1300 mV (max.) 10k Ohm AUX-IN Frequency Response Sensitivity Impedance 20 Hz - 20 kHz 775 mV 20k Ohm GENERAL Power Supply Speaker Impedance Output power Fuse 12V DC (10.8-15.
