MCD 365 INSTRUCTION MANUAL BLUETOOTH SUPPORT USB/SD/MMC INTERFACE CAR CD/MP3/WMA PLAYER/RECEIVER
MUTE BAND 1 2 3 4 5 6 DISP This unit is equipped with the most advanced “TOUCH SENSE PANEL” which is easy and convenient to use. Tips And here is some tips on how to use this touch sense panel: The pressing or activating of each button actually all you need is a very light touch, even not really necessary to “PRESS” it. Just touch lightly can be good enough to activate the button. Except for the power button, you have to touch and hold it for about 2-3 second to power on or off the unit.
1. NOTE OF DISCS MOISTURE CONDENSATION On a rainy day or in a very damp area, moisture may condense on the lenses inside the unit. Should this occur, the unit will not operate properly. In such a case, remove the disc and wait for about an hour until the moisture has evaporated. NOTES ON CDs NOTES ON DISCS 1. A dirty or defective disc may cause sound dropouts while playing. To enjoy optimum sound, handle the disc as follows. Handle the disc by its edge.
2. INSTALLATION Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and system work properly. Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle.
Removing the unit a a. Frame b. Insert fingers into the groove in the front of frame and pull out to remove the frame. (When re-attaching the frame, point the side with a groove down wards and attach it.) c. Insert the levers supplied with the unit into the grooves at both sides of the unit as shown in figure until they click. Pulling the levers makes it possible to remove the unit from the dashboard. b c Trim Plate Installation: Push the trim plate against the chassis until it is fitted.
3. DETACHABLE CONTROL PANEL (D.C.P.) Removing The Detachable Control Panel (D.C.P.). PANEL RELEASE BUTTON 1. Turn the power off 2. Press the D.C.P. release button 3. Remove the D.C.P. Attaching the DCP 2 A B 1. Attach the panel at the right side first, with point B on the main unit touching point A on the D.C.P. (As shown on the diagram). 2. Then press the left side of D.C.P. onto the main unit until a “click” sound is heard. CAUTION DO NOT insert the D.C.P from the left side. Doing so may damage it.
4. WIRING DIAGRAM ANTENNA JACK ANTENNA EXTENDER CABLE FUSE 20-PIN AUDIO/POWER HARNESS (See Figure 1) RCA-TO-RCA CABLES (not supplied) WHITE L-CH GREY REAR LINE OUT AMP L-CH WHITE R-CH RED WARNING Connecting the ISO Connector The pin arrangement for the ISO connectors depends on the type of vehicle you drive.Make sure to make the proper connections to prevent damage to the unit. The default connection for the wiring harness is described in 1 below.
6. BASIC OPERATIONS 3) PANEL RELEASE BUTTON (REL) Press this button to remove the control panel. 1) POWER ON/OFF BUTTON ( ) Long press POWER/MUTE button or any other button on the front of the radio to turn the unit on. And Long press POWER /MUTEbutton again to turn the unit off. 1) MUTE BUTTON (MUTE) Short Press the mute button momentarily to mute the audio volume, and "Mute" will flash in the display. Press the mute button again to restore volume to the previous setting.
7.MENU OPERATION 18) MENU FUNCTION LIST (MENU) Press DISPLAY/ MENU for more than 3 seconds to access the menu. Will appear in the display momentarily. Navigate the menu by pressing DISPLAY/ MENU momentarily to move forward to the next option. The menu can also be navigated by using the Tuning Up or Tuning Down Button to move to the next or previous option. Once the desired option appears in the display, adjust that option by rotating the volume control within 5 seconds.
Programmable Turn-on Volume ( P-VOL ) This option allows selection of the volume level the radio will automatically assume when first turned on. "VOL PGM 12 " is the default setting, which will turn the radio on at the volume level selected when the unit was last turned off. To program a specific volume level for the radio to turn on at, rotate the volume control to select "VOLUME LEVEL”. Within 5 seconds.
8. AUDIO OPERATION Audio Menu Long Press “AUDIO” button to access the Audio Menu. User can navigate thru the Audio Menu items by pressing the / “AUDIO” button repeatedly, or by pressing the Tuning Up or Tuning Down Button. Once the desired menu item appears on the display, adjust that option by using the Volume Up or Down button within 5 seconds. The following menu items can be adjusted as described above. The unit will automatically exit the Audio Menu after five seconds of inactivity.
9. TUNER OPERATION 7) BAND BUTTON (BAND/SEARCH) Press BAND to change between FM bands and AM(MW) bands. 20-21) TUNING UP/DOWN BUTTON ( ) Manual Tuning Press the Up Tuning or Down Tuning button for more than 3 seconds to move the radio frequency number up or down one step. Auto Seek Tuning Press the Up Tuning or Down Tuning button for less than 3 seconds to move to next station automatically. 12-17) PRESET STATIONS BUTTONS Six numbered preset buttons store and recall stations for each band.
10. RDS OPERATION RDS functions The unit is equipped with the following RDS function: - AF Alternative Frequencies CT Clock Time EON Enchanced other Network PI Program identifications PS Program service name PTY Program Type REG Regional Change TA Traffic Announcement TP Traffic program 1. AF Function By pressing AF button < 3 seconds to select AF ON/OFF. “AF ON” or “AF OFF” will show & remain on the LCD segment for 5 seconds..
11. CD /MP3/WMA OPERATION INSERT AND EJECT CD Insert a CD label-side up with the unit turned on, and the disc will begin to play. Press the Eject button to stop CD play and eject the CD. The unit does not have to be turned on to eject the CD. CD-DA OPERATION 12) PAUSE BUTTON Press the pause button to suspend disc play. Press the pause button again to resume disc Play.
Up to 200 characters can be displayed in the long file name format. For a list of available characters, see the instruction manual of the writing software and the section “Entering File and Folder Names” below.
Files Playing Order When selected for play, Folder Search, File Search or Folder Select, files and folders are accessed in the order in which they were written by the PC writer. Because of this, the order in which they are expected to be played may not match the order in which they are actually played. For example, a media with the following folder/file hierarchy is subject to Folder Search, File Search or Folder Select as shown below. An outline of a Media with MP3/WMA is shown below.
File/Folder Repeat play : Press M3 button more than 3 seconds during playing MP3/WMA disc for “repeat play” all files of the current folder. And keep on repeat playing the current folder until “repeat play” is disabled. To disable current folder “repeat play”, long press M3 button more than 3 seconds Press M3 button less than 3 seconds to “repeat play” the current file. And keep on repeat Playing the current file until the “repeat play” is disabled.
12. USB OPERATION The unit can support USB Host Function. It can playback MP3 and WMA Audio format which are stored into USB Memory Stick or USB interface Music Player. Please read below before you start the operation of USB HOST Function.
13. MEMORY CARD OPERATION The unit can support playback MP3 and WMA Audio format which are stored into SD and MMC Memory Card .
14. MUSIC FILES COPYING / TRANSFERRING Thanks for the most useful and convenient files transferring function of this unit, user can easily transfer music files between USB Stick, SD or MMC Memory card and on the CD Disc.
TRANSFER MP3 OR WMA MUSIC FILES BETWEEN MEDIA DEVICES Select a device by mode button and playback the music file need to be transfer: 1.Long press the COPY button to activate the transfer mode. 2.The LCD will display as default, Rotate the encoder volume knob to navigate thru > for selection of the storage media. 3.Once selected the storage media, Press the AUDIO button as confirmation to transfer the Playing file.
15. MUSIC FILES ERASING You can erase files from the USB Stick or Memory Card Please read below for the details operation of this function: ERASABLE MEDIA USB Stick and Memory Card. Music files which are on the CD Disc is NOT ERASABLE By this unit. ERASING MUSIC FILES ON THE MEDIA There are THREE different methods for erasing files; 1.Erase while the Music File is playing. Long press BAND button to activate the ERASE mode The LCD will display . Short Press the AUDIO to enter into the ERASE mode.
3.Erase under Files NAVIGATE search mode You can select a Music file want to erase by files Navigate Search mode After selected the music file want to erase by files navigate search, Long press BAND button to activate the ERASE mode. The LCD will display . Short Press the AUDIO button to enter into the ERASE mode Once Enter into the ERASE mode, user can rotate the encoder to select “ “ as to confirm the erase or rotate the volume knob to select “ ” to cancel the ERASE mode.
16. FILES MANAGER The advance “File Management.” System of this unit can help to well you organize all the music files just like a PC . Pls read below for details: FOLDERS MANAGEMENT This unit will automatically self-create the below default folders onto any USB /SD / MMC media device, once these devices are inserted into the unit.
17.BLUE TOOTH HAND FREE OPERATION User Guide For Blue Tooth Operation 1. When user use our Blue tooth HEAD UNIT, please make sure the mobile phone you use must / does support Blue tooth functions (Headset or Handsfree profiles or both) 2. Before you start to use our Bluetooth HEAD UNIT, please make sure complete pairing with your mobile phone first. Please refer to the user manual, section “PAIRING” for detail “PAIRING” instruction.
Bluetooth Mobile Phone Compatibility List This unit can support bluetooth specification v1.2 or higher, and compatible with bluetooth profiles such as handsfree or headset profiles. however the functionality may be limited due to some phones' own dedicated interfacing specification. This list is only updated to the time this list is being printed.
2.
3. Motorola V600 E398 V501 GX-T15 GX-T71 Features Caller ID Pairing Pairing Pairing cancel In-Band Ring Tone Ringing Talk Reject Audio Transfer Talking Volume up/down Hang up Audio Transfer Dialing Volume up/down Redial last call 4.
5. Siemens & BenQ S55 S88 Features Caller ID Pairing Pairing Pairing cancel In-Band Ring Tone Ringing Talk Reject Audio Transfer Talking Volume up/down Hang up Audio Transfer Dialing Volume up/down Redial last call 6.
7.
PAIRING Pairing The Blue Tooth System Between User’s Mobile Phone & The Unit Access into MENU - PAIRING mode to activates the operation of Pairing . Please see MENU Operation for more details of how to access into MENU mode . Once the activate the Pairing mode. is appearing on the LCD Display, press the AUDIO button to Keep the Mobile Phone within 2 meter from the unit when making the pairing. To terminate the pairing, you can press the “CLEAR / BAND” button at any time.
The unit will be Auto Re-Connection by following operation . Every time turn the ignition key from off to on, the unit will Auto re-connect with the Mobile Phone. Dis-Connection of the Blue Tooth System The unit have a option function for user to disconnect the Blue tooth system with the unit. The unit can be Dis-connected by the following methods. Access into MENU - DIS-CONN mode to activate the manual Dis-Connection. Please see MENU Operation for more details of how to access into MENU mode.
OUTGOING CALL Making An Outgoing Call User can use his / her Mobile Phone to dial and make an outgoing call. Once the user has completed the dialling, the display should show “ ”. The audio output of the present mode will ONLY be muted after pressing the “PHONE” button as a confirmation to dial the outgoing call. While there is an outgoing call or under talking mode, the Panel Open/Eject key is disactivated. During the talking mode, the LCD Display will display the duration “ ”of the conversation.
Bluetooth Audio Streaming A2DP (Advanced Audio Distribution Profile) User can listen to music files on an audio device on this unit if the audio device supports A2DP (Advanced Audio Distribution Profile) of Bluetooth Technology. Please read the below instruction before operating the Bluetooth Audio streaming function on this unit. Connecting A Bluetooth Audio Device With This Unit Before using audio device to play music on this unit, the audio device must be paired with this unit first. a.
Operating an audio device with this unit AVRCP ( Audio Video Remote Control Profile ) This unit can perform the following operations with the connecting Audio device which supports AVRCP (Audio Video Remote Control Profile) & only if the Audio device does support AVRCP. (1) Start playing - Every time when user change mode into “BT AUDIO” mode, this unit will automatically send a “PLAY” command via AVRCP to the audio device to command the auto start playing song in the audio device.
18.SPECIFICATIONS CD PLAYER System Usable disc Sampling frequency No of quantization bits Frequency Number of channels S/N Ratio Compact disc audio system Compact disc 44.1KHz 1bit 5-20,000Hz 2 stereo 70dB MEDIA SECTION USB Host Host 1.1 compatibles 2.0 Memory Card Support Type of Memory Card SD and MMC RADIO SECTION FM Frequency Range Intermediate Frequency UsableSensitivity StereoSeparation S/NRatio 87.5-108 Mhz 10.
19.TROUBLE SHOOTING Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer. Symptom Cause Solution No power The car ignition is not on. The fuse is blown. Replace the fuse. Disc cannot be loaded or ejected Presence of CD disc inside the player. Remove the disc in the player, then put a new one. Inserting the disc in reverse direction. Insert the compact disc with the label facing upward.
