MCD 175 INSTRUCTION MANUAL CAR CD/MP3 PLAYER / RDS RECEIVER
1. HANDLING COMPACT DISCS MOISTURE CONDENSATION On a rainy day or in a very damp area, moisture may condense on the lenses inside the unit. Should this occur, the unit will not operate properly. In such a case, remove the disc and wait for about an hour until the moisture has evaporated. NOTES ON CDs NOTES ON DISCS 1. A dirty or defective disc may cause sound dropouts while playing. To enjoy optimum sound, handle the disc as follows. Handle the disc by its edge.
2. INSTALLATION Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and system work properly. Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle.
Removing the unit a a. Frame b. Insert fingers into the groove in the front of frame and pull out to remove the frame. (When re-attaching the frame, point the side with a groove down wards and attach it.) c. Insert the levers supplied with the unit into the grooves at both sides of the unit as shown in figure until they click. Pulling the levers makes it possible to remove the unit from the dashboard. b c Trim Plate Installation: Push the trim plate against the chassis until it is fitted.
3. DETACHABLE CONTROL PANEL (D.C.P.) Removing The Detachable Control Panel (D.C.P.). PANEL RELEASE BUTTON 1. Turn the power off 2. Press the D.C.P. release button 3. Remove the D.C.P. Attaching the DCP 2 A B 1. Attach the panel at the right side first, with point B on the main unit touching point A on the D.C.P. (As shown on the digram). 2. Then press the left side of D.C.P. onto the main unit until a “click” sound is heard. CAUTION DO NOT insert the D.C.P from the left side. Doing so may damage it.
4. WIRING DIAGRAM ANTENNA SHOCKET ANTENNA JACK FUSE 20-PIN AUDIO/POWER HARNESS (See Figure 1) AMP RED R-CH (RED) Ignition wire (YELLOW) Battery wire WARNING Connecting the ISO Connector The pin arrangement for the ISO connectors depends on the type of vehicle you drive.Make sure to make the proper connections to prevent damage to the unit. The default connection for the wiring harness is described in 1 below. If the ISO connector pins are set as described in 2 or 3 .
5. BASIC OPERATIONS 1) PANEL RELEASE BUTTON (REL) Press this button to remove the control panel. 13) POWER ON/OFF BUTTON ( ) Press the POWER button on the front of the unit to turn on the unit. Long press the POWER button to turn Off the unit. 11) DISP BUTTON(DISP) Press this button to view clock, Programme Type (PTY), and Frequency of the station in listening. 2) ENCODER VOLUME KNOB Turn this knob to adjust desired volume level.
6. AUDIO OPERATIONS 2) ENCODER VOLUME KNOB Turn this knob to adjust desired volume level. 3) MENU / SELECT BUTTON Press this button to select desired audio function. ORDER OF FUNCTION: VOL->BASS (BAS)->TREBLE (TRE)->BALANCE (BAL)-> FADER (FAD) While the selected function is displayed, turn Volume Knob to adjust the level within 5 seconds, otherwise the unit will return to volume adjustment mode.
7. RADIO OPERATIONS 9) RADIO SIGNAL STRENGTH METER (RSLM) This is use to indicate the signal strength of current radio station broadcast. When you choose RADIO mode, it will show on the display. Best reception Worst reception 7) STATION PRESET BUTTONS (M1-M6) 1.Press these buttons briefly to recall the stored stations in the selected band. 2.Presetting stations manually, Press the BAND button to select the band for the station to be preset. Use Tuning Up/Down to tune in the stations to be preset.
8. RDS OPERATIONS 5) AF BUTTON(ALTERNATIVE FREQUENCIES) When pressed short, AF switching mode is selected. When AF switching mode is selected, the radio check the signal strength of the AF all the time. When pressed long, it is activated as regional mode ON/OFF. - Regional mode ON: AF Switching or PI SEEK is implemented to the station which have all PI codes are same as current station. REG segment is turned on, in LCD display.
OVERVIEW OF THE RDS FUNCTION Radio Data System (RDS) is a broadcasting service that allows FM stations to send additional digital information along with the regular radio program signal. Your car stereo offers you a variety of services. Here are just a few: - PI (Program identification) It is a code that identified RDS stations; it is unique for each station. - PS (PROGRAM Service Name) The name of current station, it is shown on the display.
PROGRAMMABLE OPTIONALS To use this function keep press long AUDIO MENU Button for few seconds, each time you press this button the mode will move and the functions will shown on the display, turn the encoder volume knob up/ down to set the desires functions ,the function states as following: - TA ON/OFF Turn the encoder volume to select the TA function ON/OFF. - TA SEEK, TA ALARM To determine what action will the radio take if the newly tuned station does not receive TP information for 5 seconds.
9.CD OPERATIONS 4) CD SLOT Insert the disc into CD slot. The CD will begin to play. M1) PAUSE BUTTON (PAU) Press this button to pause CD play, press again to release pause. M2) INTROL BUTTON (INT) Press this button, the first 10 seconds of each track will be played sequentially until this button is pressed again, then normal play will resume at the current track. M3) REPEAT BUTTON (RPT) Press this button, the current track will be played repeatedly until this button is pressed again.
PLEASE READ THIS INSTRUCTION CAREFULLY BEFORE OPERATING THE UNIT 10. USB DRIVE OPERATIONS COMPATIBILITY Due to the fast changing technology world, this unit may or may not be compatible to all the USB drive / device available with all the future technology, especially those USB drive / device which require to install a driver. Always choose a compatible USB drive / device which is compatible with this unit. P.1 NOTE: This unit is not compatible with portable Hard-Disk.
11. SD/MMC OPERATIONS 1.Press panel release button to release the front panel.(P.1) 2.The SD/MMC card slot is located on the unit as indicated in (P.2). 3. Insert the SD/MMC card into the card slot in the correct direction until a “CLICK” sound is heard.(P.3) 4.Close the front panel.(P.4) P.2 P.1 P.3 Face Up P.4 Click Only for MCD275 Detach the Front Panel Insert the SD/MMC Card with Label up side Push in till heard a “click” Close the front Panel 5.
12.MP3/WMA OPERATIONS Notes : This unit support : MPEG1/2/2.5/ Layer 2/3 WMA Version 7/8/9 Sampling frequency - MPEG1 : 32/44.1/48 KHz - MPEG2 :16/22.05/24 KHz - MPEG2.5 : 8/11.025/12KHz - WMA : 22/32/44/48KHz Sampling But rate - MP3/WMA : 32~320Kbps & VBR CDROM Mode 1 / 2 ISO9660 Level 1 / 2 & Joliet(unicode) Max File/DIR. Count : 255 Max DIR. Depth : 255 Sorting Method : Tree sorting Max File/DIR. Name : 64Byte ID3 V1.0/1.1/2.0/2.
ENTER BUTTON and continue to search the directory or file name in the directory by TUNE UP / DOWN Button (TUNE DOWN First).
13.SPECIFICATIONS CD PLAYER System Usable disc Sampling frequency No of quantization bits Frequency Number of channels S/N Ration Compact disc audio system Compact disc 44.1KHz 1bit 5-20,000Hz 2 stereo 70dB RADIO SECTION FM Frequency Range Intermediate Frequency Usable Sensitivity Stereo Separation S/N Ratio 87.5-108 Mhz 10.
14.TROUBLE SHOOTING Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer. Symptom No power Disc cannot be loaded or ejected Cause Solution The car ignition is not on. If the power supply is properly connected to the car accessory terminal, switch the ignition key to “ACC” The fuse is blown. Replace the fuse. Presence of CD disc inside the player.
