INSTALLATION Tools for Installation Use the 2 removal wrenches of the old unit to take out the old unit and place with this brand new car radio. The following tools and supplies may also be needed for the installation: Tools for Installation: Philips Screw-drivers /Machine Screws /Wire Stripper /Wire Cutter /Hammer /Pencil /Electrical Tape /Electric Drill Supplies for Installation: Machine Screws /Crimp Connectors /14 Gauge Wire for Power Connections /14-16 Gauge Speaker Wires The above are not supplied.
INSTALLATION WARNING: Disconnect negative battery terminal from battery before starting installation. Consult the vehicle’s owner’s manual for proper instructions. NOTE: Mark the polarity of the existing speaker wires before disconnecting battery. NOTE: Remove the two transport screws from the top of the unit before installing. NOTE: Make sure there is enough space for the installation of this double-din unit.
WIRING DIAGRAM Amplifier power CAMERA BACK (+12V output - blue/white) External Microphone (black - 3,5mm Jack) Radio Antenna SWC (steering wheel control - 3.5mm jack) Reverse(purple-white) Parking (green) Connector A 1. Rear right speaker(+)/Purple 2. Rear right speaker(-)/Purple-Black 3. Front right speaker(+)/Grey 4. Front right speaker(-)/Grey-Black 5. Front left speaker(+)/White 6. Front left speaker(-)/White-Black 7. Rear left speaker(+)/Green 8.
WIRING DIAGRAM General Wiring Notes: Make sure You have a good chassis ground. Good ground connection will eliminate most electrical noise problems. A good chassis ground requires a tight connection to the .vehicle’s metal chassis. The area around the ground connection should be clean, bare metal without rust, paint, plastic, dust, or dirt for a good ground connection. Black Ground Connect to vehicle body/chassis. Make sure you have a good chassis ground.
Specifications GENERAL Operating Power.......................................................................................................................................12 Volts DC, Negative Ground Output Wiring...............................................................................................................................Designed for using four speakers only RCA line out........................................................................................................................
BASIC OPERATION 1. Tuning the unit On / Off Press the Power Button to turn the unit on. The opening screen of the unit will be showing on the TFT monitor. Press and hold the POWER button again to turn the unit off. 2. Turning the TFT On / Off During any play mode, press the Power Button once to turn the TFT screen off for screen saving and avoid distraction while driving. The sound will continue to play. Press the Power Button again to turn the TFT screen back on. 3.
BASIC OPERATION 7. SETUP Enter the setup menu in the home screen by tapping the “SETTING” icon on the main menu. Tap the items you would like to set. You can adjust audio, date and time, language, cabibration, wallpaper,etc. 8. Day Light Saving Tap the Day button on the OSD to increase brightness. Tap again to reduce brightness during night time. Tap again for black out the screen.
Radio Operation 1. Choose Radio Band Touch the AM button on screen to choose among the five radio bands - three FM Bands (FM1, FM2, and FM3) and two AM Bands (AM1, and AM2). Each of the five bands can store up to six preset stations, for a total of 30 preset memory stations. 2. Radio Seek Function In Radio Mode, touch and hold> or < Button to adjust the radio frequency automatically. Press the button once to adjust the radio frequency manually. 3.
DVD/VCD/CD Operation 1. Selecting Tracks Press the SEEK >>| Button to advance to the next track. Track numbers will be shown on the display. Press the SEEK >> to fast forward. Press the SEEK |<< Button to go to a previous track. Track numbers will be shown on the display. Press the SEEK << Button to fast reverse. Press >|| button, disc will puase to play, Press it again disc will play again. On the Remote Control, use the |<< or >>| Buttons. 2.
DVD/VCD/CD Operation (Con’d) 8. Track Search Press the GOTO button to search the desired track to play the Disc. The OSD will be prompted. Make use of the navigation keys and digit keys on the touch screen to choose your desired chapter, track. Press the ENTER button to confirm your selection. 9. Repeat Function Press the Repeat button to toggle between repeat chapter, repeat title, repeat all and repeat off. 10. Menu Playing (for DVD only) Tap so that the menu of the disc will be prompted 11.
DVD/VCD/CD Operation (Con’d) 17. Electronic Skip Protection This unit is programmed with Electronic Shock Protection (ESP) so that the video will be protected against rough roads for 5 seconds. 18. Returning to Main User Interface Press the “BACK” button or “MENU” button to return to the main user interface. Mixed Disc / USB-SD Operation While you are playing mixed disc, USB, or SD card which contains MP3, WMA, JPG or DIVX formats, the unit will directly play the audio files.
Bluetooth Operation PAIRING At BT mode, search bluetooth device by the phone and “RDD802BT Caliber” will appear in your phone. Input “0000” as password to establish connection. DIAL PAD Touch the dial pad to dial the number you would like to call. Touch the CALL (green) button to send the number. CALL RECORD Press the HISTORY button to enter the phone book page to view received, missed and dialed calls. More details in the next page.
Settings General Setting The general setting menu includes wallpaper, logo, Key Beep, radio region, RDS region, aspect ratio, warning, calibration. Time Setting You can select Date, Time, Time mode and Time zone by tapping > directly on the options or the arrows for up/down. Tap “BACK” after the setting to take effect. Language Setting There are diferent languages to select.You can select the language you want for OSD, disc menu, disc audio and disc subtitle.
INFRA RED REMOTE CONTROL 1 2 3 MOD 5 6 7 8 9 10 11 12 13 14 15 16 17 MUTE TITLE BAND ANGLE ST PROG LOC RDM SEEK SUB-T SETUP ENTER AMS RPT 4 VOL SELECT PBC OSD 1 2 5 6 7 9 0 10 VOL 3 SLOW ZOOM SEEK AUDIO 4 18 19 20 21 22 23 24 25 26 27 28 29 8 GO TO 30 1.Power on/off 2. Mode Select Key 3.Play / Pause Function 4.Mute Sound Function 5.Band Select 6/7/10/21.Cursor Button in Menu Mode 8.Confirm The Track/Chapter Selected or Select Item In SETUP Menu 9. Stop Playback 11.
