Brochure

2
23
NA546
DISCAL DIRT
Air & Dirt separator.
Epoxy resin coated steel body.
Stainless steel oat guide pin and linkage.
Stainless steel mesh internal element.
1" (2—6" sizes) and 2" (8—14" sizes)
threaded NPT bottom drain connection.
ANSI 150 ange connections.
Complete with drain valve NA39753
(2—6" sizes), NA59600 (8—14" sizes).
Max. working pressure: 150 psi.
Vessel temperature range: 32—270°F.
ASME registered. CRN registered thru 12".
Consult factory for 14".
ASME U-stamp tagged and registered with the National Board of Boiler and
Pressure Vessel Inspectors; CRN registered, 2"— 12"; consult factory for
14".
ASME/CRN
MAXIMUM FLOW RATE
Size 2" 2½" 3" 4" 5" 6" 8" 10" 12" 14"
GPM 100 155 220 400 615 880 1,570 2,450 3,525 4,800
Cv 87 174 208 324 520 832 1,109 1,387 1,664 1,967
ASME/CRN
*With one magnet
**With three magnets
ASME U-stamp tagged and registered with the National Board of Boiler and Pres-
sure Vessel Inspectors. CRN registered, 2" — 12"; consult factory for 14".
NA546M
DISCAL DIRTMAG
AIR AND DIRT SEPARATORS
Air & Dirt separator with magnets.
Epoxy resin coated steel body.
Stainless steel oat guide pin and linkage.
Stainless steel mesh internal element.
ANSI 150 ange connections.
1" (2—6" sizes) and 2" (8—14" sizes)
threaded NPT bottom drain connection.
Complete with drain valve NA39753
(2—6" sizes), NA59600 (8—14" sizes).
Max. working pressure: 150 psi.
Vessel temperature range: 32—270°F.
Particle separation capacity: to 5 µm (0.2 mil).
Ferrous impurities separation efciency: up
to 100%.
ASME registered. CRN registered thru 12".
Consult factory for 14".
Code Description Lbs USD
NA546050TM* 2" Threaded ASME & CRN 31 3,661.00
NA546060AM* 2½" ANSI flange ASME & CRN 45 4,786.00
NA546080AM* 3" ANSI flange ASME & CRN 76 6,228.00
NA546100AM* 4" ANSI flange ASME & CRN 81 6,771.00
NA546120AM* 5" ANSI flange ASME & CRN 184 9,945.00
NA546150AM* 6" ANSI flange ASME & CRN 191 12,000.00
NA546200AM** 8" ANSI flange ASME & CRN 365 23,542.00
NA546250AM** 10" ANSI flange ASME & CRN 565 33,991.00
NA546300AM** 12" ANSI flange ASME & CRN 835 43,071.00
NA546350AM** 14" ANSI flange ASME 960 53,832.00
®
In the DISCALDIRTMAG
TM
air and dirt separator with
magnets ferrous impurities are
captured by a concentrated
magnetic eld created by a
stack of neodymium rare-earth
magnets positioned inside a
brass dry-well which is below
the ow stream. Non-magnetic
dirt particles are separated by
colliding with an internal element
in the ow stream and settling to
the bottom. The deep collection
chamber keeps the dirt from re-
entering the ow stream. The
dirt and ferrous impurities are
ushed out while the system
is operating, by removing the
magnets and opening the purge
valve.
Code Description Lbs USD
NA546050T 2" Threaded ASME & CRN 28 3,168.00
NA546060A 2½" ANSI flange ASME & CRN 42 4,261.00
NA546080A 3" ANSI flange ASME & CRN 73 5,487.00
NA546100A 4" ANSI flange ASME & CRN 78 6,016.00
NA546120A 5" ANSI flange ASME & CRN 181 8,678.00
NA546150A 6" ANSI flange ASME & CRN 188 11,068.00
NA546200A 8" ANSI flange ASME & CRN 355 20,559.00
NA546250A 10" ANSI flange ASME & CRN 555 31,610.00
NA546300A 12" ANSI flange ASME & CRN 825 39,528.00
NA546350A 14" ANSI flange ASME 950 49,982.00
1
2 2
3
3
1
LARGE DIAMETER
DIRT COLLECTION
CHAMBER
DRAIN VALVE
NA546M
NA546
COALESCING
MESH
MAGNETS
HANDLE
Low head losses and high performance are maintained over time. The dirt
separating action performed by the DISCALDIRT
®
air and dirt separator is
based on using the internal element with concentric diamond pattern mesh
surfaces instead of an ordinary lter. The element offers little resistance to
the medium ow while ensuring dirt separation. This occurs due to the
particles colliding with the concentric diamond pattern mesh surfaces
and then settling to the bottom, and not by ltration; which, over time,
gets progressively clogged. By contrast, the DISCALDIRT
®
low-velocity
zone air and dirt separator efciently removes the particles to as small
as 5 μm (0.2 mil) with very low head loss. The dirt collection chamber
at the bottom of the DISCALDIRT
®
is at the right distance from the inlet
and outlet connections so that the collected dirt particles are not affected
by the swirling ow through the bottom drain port, even with the system
running, by opening the drain valve with the handle.
™