User's Manual
Table Of Contents
- 1 VIPER OVERVIEW
- 2 SYSTEM ARCHITECTURE AND NETWORK PLANNING
- 3 DATARADIO VIPER QUICK START
- 4 VIPER WEB MANAGEMENT
- 5 UNIT STATUS
- 6 SETUP (BASIC)
- 7 SETUP (ADVANCED)
- 7.1 RF OPTIMIZATIONS
- 7.2 IP SERVICES
- 7.3 IP ADDRESSING
- 7.4 IP OPTIMIZATION
- 7.5 IP ROUTING (TABLE/ENTRIES)
- 7.6 TIME SOURCE
- 7.7 ALARM REPORTING
- 7.8 USER SETTINGS
- 8 SECURITY
- 9 STATISTICS
- 10 MAINTENANCE
- 11 NEIGHBOR MANAGEMENT
- 12 NETWORK OPTIMIZATION
- 13 UPGRADING YOUR FIRMWARE
- VIPER SPECIFICATIONS
- PRODUCT WARRANTY
- DEFINITIONS
001-5008-000(Rev8) Page 15
1.4 PART NUMBERS AND AVAILABILITY
1.4.1 Viper Radio
Table 1-5 provides a breakdown of the Viper part number
Table 1-5 - Part Number Breakdown
Model Number Description
Frequency Range
140-5018-500 Standard VHF Viper
136 - 174 MHz
140-5028-502 Standard VHF Viper-200 215 - 240 MHz
140-5048-300 Standard UHF Viper Range 3
406.1 - 470 MHz
140-5048-400
Standard UHF Viper Range 3
(EN 300 113 Compliant,
AS/NZ Compliant)
406.1 - 470 MHz
140-5048-500 Standard UHF Viper Range 5
450 - 512 MHz
140-5048-600
Standard UHF Viper Range 5
(AS/NZ Compliant)
450 - 512 MHz
140-5098-500 Standard 900MHz Viper
928 - 960 MHz
140-5018-501 Dual Port VHF Viper 136 - 174 MHz
140-5028-503 Dual Port VHF Viper-200 215 - 240 MHz
140-5048-301 Dual Port UHF Viper Range 3
406.1 - 470 MHz
140-5048-501 Dual Port UHF Viper Range 5
450 - 512 MHz
140-5098-501 Dual Port 900MHz Viper
928 - 960 MHz
1.4.2 Accessories and Options
Table 1-6 - Table 1-8 list standard accessories (including antenna, feedline, and connectors)
tested and approved for use with the Viper.
Table 1-6 - Accessories
ITEM PART NUMBER
Viper Power Cable 897-5008-010
Viper Demo Kit* – VHF - 136-174 MHz 250-5018-500
Viper Demo Kit* – VHF 200 - 215-240 MHz 250-5028-502
Viper Demo Kit* – UHF - 406-470 MHz 250-5048-300
Viper Demo Kit* – UHF - 450-512 MHz 250-5048-500
Viper Demo Kit* – 900 - 928-960 MHz 250-5098-500
Factory Installed Viper Fan Kit 150-5008-001
Field Installed Viper Fan Kit** 150-5008-002
TNC-Male to N-Male 18” 250-0697-103
TNC-Male to N-Male 48” 250-0697-104
TNC-Male to N-Male 72” 250-0697-105
TNC-Male to N-Female 18” 250-0697-106
* The Viper Demo Kit includes two of each of the following: Viper, rubber duck antennas, adapters, attenuators,
power cables, and power supplies.
** The field install Fan Kit is available for all VHF 200/UHF/900 Vipers (140-5028-XXX/140-5048-xxx/140-5098-
xxx) but is only available for VHF models-(140-5018-xxx) with RF revision 0.3 or greater (shipping Fall 2008).
Contact CalAmp Technical Support for more information.