INTRODUCTION Your cordless telephone is designed to give you flexibility in use and high quality performance. To get the most from your new cordless telephone, we suggest that you take a few minutes tight now to read through this instruction manual; TABLE OF CONTENTS GETTING STARTED MODULAR JACK REQUIREMENT. HANDSET SETUP--DESKTOP INSTALLATION Ware MOUNT INSTALLATION CORDLESS PHONE Basics Receiving A TALL FLASH BUTTON ADJUSTING THE VOLUME HANDSET EARPIECE VOLUME.
GETTING STARTED Make sure your package includes the items shown here. MODULAR JACK REQUIREMENTS You need an RJ11 type modular jack, which is the most Common type of phone jack and might look like the one Pictured here. If you don't have a modular Jack, call your local phone company lo find out how to get one installed, INSTALLATION NOTE: Some cordless telephones operate at frequencies that may cause interference to nearby TVs and VCR.
HANDSET SETUP Insert the battery into the compartment. 2.install the battery compartment door, IMPORTANT; if you don’t charge the handset battery perforation 12 hours) when yeu first set up the phone, the battery's long-term performance will be compromised. —— a —— Tip: In order to maximize your battery's use, we recommend that you periodically use the handset without returning it to the base to drain the battery completely, then recharge for 12 hours.
DESKTOP INSTALLATION 1.Plug the telephone line cord into the PHONE LINE jack on the back of The base and into a modular jack. 2.Plug the power supply cord into the SV DC jack on the base and into an AC outlet. 3.Set the TONE/PULSE switch to TONE for touch-tame service, or PULSE for rotary service. If you don't know which type of service you have, Check with the phone company. 4.Select RINGER ON or OFF (on the side of handstand. When you select OFF, the handset doesn't ring 5.Raise the base antenna, 6.
WALL MOUNT INSTALLATION 1. Plug the short telephone line cord into the PHONE LINE jack on the back of the base and into a modular jack. IS . Plug the power supply cord into the 9v DC jack on the base and into an AC outlet. w install the base plate by putting the tabs into the slots on the top of the unit first, and then snapping the bot torn tabs into place, ~ . Slip the mounting holes aver the wall plate posts and slide the unit down firmly into place. {wall plate not included.
CORDLESS PHONE Basics MAKING A CALL After initial set up, the handset battery should be charged for at least 12 hours, The only two things you need to know to make a call sre: -Press the TALK button before you dial. iE you try to make a calf when you're too far away from the base, the handset beeps, -Press TALK or place the handset in the base to hang up.
of the base, you must press the TALK button before you can tail. Fast Burton Use the FLASH button to activate custom calling service such as call waiting or call transfer, which are available through your local phone company. IMPORTANT. Don't use the TALK button to Activate custom calling services such as call Waiting, or you'll hang up the phone. ADJUSTING THE VOLUME The VOL up and down buttons on the handset control the volume of the handsets earpiece and the ringer Volume.
RINGER Volume To adjust the finger volume, press the VOL up or down buttons when the phone is an-hook (phone is inactive, TAKE light is off). SELECTING A RING TONE There are 4 ding tones built into your phone. To choose a ding tone, press FLASH followed by either 1,23, or 4 When the phone is on-hook (phone is Inactive, TALK lights off).
| 4.Follow the bank's voice instructions to complete your transaction, 8.Hang up when finished. The pane returns to pulse {rotary) service, PAGING THE HANDSET Press the Partridge button on the base to get the attention of somebody who is using the handles or to locate a misplaced handset. When you press PAGE/FIND on the base, the handset beeps (the CHARGE/IN USE light on the base the TALK button when you locate the handset to stop the PAGE/FIND feature.
_Abeyance FEATURES THE Memory Features Store up to 20 numbers in memory for quick dialing. STORING A Nurser iy Memory The phone must be off when you store numbers. 1.Press the MEMORY button {TALK light blinks), 2.Dial the number {unto 18 digits). 3.Press MEMORY, 4.Use the keypad to enter a 2-digit number (01-20) to store the number in that REDIAL BUTTON Member location (the phone beeps).
DIALING A Stoned Newman 1. Press the TALK button to get a dial tone, 2.Press MEMORY, 3.Press any number key (01-20) to store the dialed number in that memory location, ADDING A PAUSE WHEN vou store 4 NUMBER IN Memory Use the REDIAL/IPAUSE button to insert a Pause in the dialing sequence when you store a number (for example, when you must dial 9 to get an outside fine or enter codes to access your bank's information fine). To add a pause because you must dial 9 to get outside fine: 1.Press MEMORY. 2.Press 9.
_ STORING A TEMPORARY Tong Nurser iv Memory 1.Press the MEMORY bunion, 2.Dial the number {up to 16 digits). 3.Press the TONE button to switch to tone dialing. (The TONE counts as one digit.) 4.Enter authorization code/access numbers, 5.Press MEMORY. 6.
L HANDSET BATTERY INFORMATION BATTERY Savagery Precautions ~Don't disassemble, mutilate, puncture, wet, or dispose of battery in fire. Like other batteries of this type.
CHANGING THE BA; BUTTERY keep the battery adequately charged. The handset runs on a consumer-replaceable, nickel-cadmium battery pack. If you experience any of the following problems, yoy may need to replace the battery pack: shod talk time, poor sound quality, limited range, CHAR E/N USE light fails to light. Make sure phone is OFF before you replace battery. 1.Remove the battery compartment door. 2.Remove the battery pack 3.insert the new battery into the compartment on the back of the handset, 4.
J TROUBLESHOOTING GUIDE In case of different, please check the following troubleshooting Guide before seeking service. Problem Solution No dia tone Dial tong is OK, but cant _dial out Handel does net ring Check installation: 18 the base power cord connected to a working outlet? + Is TALK light on? +Is the telephone ling God connected to the base unit and the wall jack? “Disconnect the base form the wall jack and connect another phone to the same jack. If there is no dial tone in the secant phone.
_ Ur nit beeps, You may be receiving a Nn out-of rang alert, Move closer to the base, reset is successful, Put handset in base for battery, -Clean charging contacts on base with a soft cloth or an -See solutions for trey. handset ang eraser.
GENERAL Producer CARE oe STREETCAR To keep your telephones: working ang fooling good, follow these Guidelines: fluorescent lamps). -00 NOT Expose to direct sunlight or moisture, -Avoid dropping the handset, as well as other rough treatment to the phone. ~Clean the phone with a soft cloth, -Never use 5 strong cleaning agent or abrasive powder because this will damage the finish, phone at a (tare date. -Periodically clean the charge contacts On the handset ang base with a soft cloth, 17.
CAUSE of Poor RECEIPT ION “Aluminum siding. ~Foil backing on insulation. ~Heating ducts and other meta} construction can shield radio signals, -You're toa close to appliances such as Microwaves, stoves, Computers, etc. “Atmospheric conditions, such as siring storms. -Base is installed in the basement of lower floor of the house. -Base is plugged into an AC outlet with other electronic devices, -Handset battery is low, -You're out of.