Specifications

CSB912P2NS1
Café™ 27" Five in One Oven
with 120V Advantium® Technology
© 2020 GE Appliances PC95218 10/20
For answers to your Café™ product questions, visit our website at cafeappliances.com.
CXWS7H0PNBZ
Brushed Bronze
1 handle
CXWS7H0PNSS
Brushed Stainless
1 handle
CXWS7H0PNBT
Brushed Black
1 handle
CXWS7H0PNCU
Brushed Copper
1 handle
ADDITIONAL ACCESSORIES
DIMENSIONS AND INSTALLATION INFORMATION
Prepare the opening: The Advantium Built-In Oven can be installed in
combination with other appliances. Always follow each product's Installation
Instructions to compete the installation.
Single oven installation: Order a 30" or 27" wide single oven cabinet or cut
the opening in a wall to the dimensions shown.
* For existing cutouts, a maximum width of 28-1/2" is acceptable. If the
opening is slightly wider, secure a furring strip on each side of the
cutout for securing the oven.
- The unit overlap on the top is 1−3/4" but allow 1−7/8" clearance from top edge
of cutout. The unit overlap on each side is 3/4" but allow 7/8" clearance from
side edges of cutout. The unit overlap on the bottom is 1" but allow 1−1/8"
clearance from bottom edge of cutout.
- Oven overlaps will conceal cut edges on all sides of the opening.
Preparation with a Warming Drawer
When installed over a single oven or a warming drawer, allow at least
2" between the two openings. This separation will provide clearance for
bottom overlap of the Advantium Built-In Oven and the other appliance
overlaps.
Construct a solid oven floor of 3/8" min. thick plywood supported by 2 x 4
or 2 x 2 runners on all sides.
- the support must be level and rigidly mounted, flush with the bottom edge
of the cutout.
* For existing cutouts, a maximum width of 28-1/2" is acceptable. If the opening
is slightly wider, secure a furring strip on each side of the cutout for securing
the oven.
Note: Additional clearances between the cutouts may be required. Check to
be sure the oven supports above the Warming Drawer location do not obstruct
the required interior depth and height. See Warming Drawer installation
instructions for details.
Installation Over a Wall Oven and Warming Drawer:
* For existing cutouts, a maximum width of 28-1/2" is acceptable. If the opening
is slightly wider, secure a furring strip on each side of the cutout for securing
the oven.
Note: Additional clearances between the cutouts may be required. Check
to be sure the oven supports above the Warming Drawer location do not
obstruct the required interior depth and height. See Warming Drawer
installation instructions for details.
Caution: For personal safety, the mounting surface must be capable of
supporting the cabinet load, in addition to the added weight of the
oven and drawer, plus additional oven loads.
25-1/4"
23-1/2"
Construct base -
Min. 3/8" plywood
supported by 2x4
or 2x2 runners all
four sides.
17-1/2"
27" or 30"
36-3/4"
Min.
25-1/4"
23-1/2"
Construct base -
Min. 3/8" plywood
supported by 2x4
or 2x2 runners all
four sides.
17-1/2"
27" or 30"
36-3/4"
Min.
Installation over Warming Drawer:
2" Min.
(3" recommended)
Per warming
drawer
requirement
23-1/2"
Construct solid
bottom - Min. 3/8"
plywood supported
by 2x4 or 2x2
runners all four
sides
17-1/2"
27" or 30"
45-1/4"
Min.
Installation over a Wall Oven and Warming Drawer:
2" Min.
(3" recommended)
2" Min.
Per oven
requirement
25-1/4"
Per warming drawer requirement