Specification

Café
™
30" Built-In Touch Control Electric Cooktop
CEP90302TSS / CEP90301TBB
For answers to your Café™ product questions, visit our website at cafeappliances.com.
DIMENSIONS AND INSTALLATION
Important: Requires a 5" free area between the bottom of the cooktop to any
combustible material, i.e., shelving. Free area not required when installing wall
oven underneath cooktop. Refer to installation instructions. Requires a 15"
minimum from cooktop to adjacent overhead cabinets. Units are furnished
with a 48" flexible armored cable.
Note: 30" Ribbon cooktops are approved for use over select Café 27" and
Café 30" Single Wall Ovens and Warming Drawers. Refer to cooktop and wall
oven/warming drawer installation instructions packed with product for current
dimensional data. If installed with a Telescopic Downdraft System, consult both
the cooktop and downdraft installation instructions packed with product before
installing. Cooktop gas/electric supply may need to be re-routed to install
downdraft. The countertop cutout requires 23-1/2" minimum flat countertop
surface and 25" minimum total countertop depth. In addition, other clearances
to front edge of the countertop must be considered. Before installing, consult
installation instructions packed with product for current dimensional data.
Cutout filler trim kit: A filler trim kit is available for use if your countertop cutout
is larger than the dimension shown, up to 29-13/16" x 20-7/16". Order JXTR32B
to reduce the cutout opening for installation of this cooktop. These kits may be
ordered from your Café Appliances Dealer.
2-1/2" MIN
From front edge
of countertop to front
edge of cooktop cutout
31-1/4
" MIN
From top surface
of countertop to
top surface of
wall oven support
platform
INSTALLATION ABOVE A WALL OVEN
Installation above a wall oven
Voltage (60HZ AC) 240V 208V
Connected load (max.) 9.4Kw 7.1Kw
Current draw (max.) 39.2 Amps 33.9 Amps
Recommended circuit breaker† 40 Amps 40 Amps
†
Note: Check local codes for required breaker size.
Approximate Cooking Dimensions
To insure accuracy, it is best to make a
template when cutting the opening in the counter
Cooktop
29-7/8"
21"
19-1/4"
28"
19-5/8" to
19-3/4"
28-1/2" to
28-5/8"
2-1/2" MIN.
Required
1-3/4" MIN.
to rear wall
3-9/16" at front of unit and
5-9/16" at conduit location
13" MAX. depth of unprotected
overhead cabinets
15" MIN. Clearance
from countertop
to underside of
nearest cabinet
on both sides of
cooktop, including
any light rails.
30" MIN. Clearance from
countertop to unprotected
overhead surface
2" MIN. Clearance
from cutout to
nearest vertical
wall or cabinet on
left side of the unit
below the 15" MIN.
clearance height.
1 1/2" MIN. (30") and
2" MIN. (36") Clearance
from cutout to nearest
vertical wall or cabinet
on right side of the unit
below the 15" MIN.
clearance height.
30" MIN. for
30" cooktop
To insure accuracy, it is best to make a
template when cutting the opening in the counter
Cooktop
29-7/8"
21"
19-1/4"
28"
19-5/8" to
19-3/4"
28-1/2" to
28-5/8"
2-1/2" MIN.
Required
1-3/4" MIN.
to rear wall
3-9/16" at front of unit and
5-9/16" at conduit location
13" MAX. depth of unprotected
overhead cabinets
15" MIN. Clearance
from countertop
to underside of
nearest cabinet
on both sides of
cooktop, including
any light rails.
30" MIN. Clearance from
countertop to unprotected
overhead surface
2" MIN. Clearance
from cutout to
nearest vertical
wall or cabinet on
left side of the unit
below the 15" MIN.
clearance height.
1 1/2" MIN. (30") and
2" MIN. (36") Clearance
from cutout to nearest
vertical wall or cabinet
on right side of the unit
below the 15" MIN.
clearance height.
30" MIN. for
30" cooktop
WARRANTY
Parts warranty
Limited 1-year entire appliance
90 days post-install on cooktop glass
Labor warranty Limited 1-year entire appliance
Warranty notes See written warranty for full details
© 2022 GE Appliances 10/22