LP Conversion Kit
ADDITIONAL INFORMATION
ADJUSTING LOW FLAME SETTING
ON COOKTOP BURNERS
Center adjustment screw only for all other burners.
SPECIAL NOTE:
To convert the oven back to natural gas, reverse the
instructions given in making propane (LP) adjustments.
Adjustment screws for multi-ring burner only
Adjustment
screw for
outer ring
Adjustment
screw for
center ring
NOTICE:
2QFHWKHFRQYHUVLRQLVFRPSOHWHDQGFRQ¿UPHG¿OORXWWKH
propane (LP) sticker and include your name, organization
and date conversion was made. Apply the sticker to the
range near the regulator to alert others in the future that
this appliance has been converted to propane (LP). If
converting back to natural gas from propane (LP), please
remove the sticker so others know the appliance is set to
use natural gas.
BURNER OUTPUT RATINGS: BTU/HR
NG (Natural) Gas 5” W.C.P.
BURNER
BTU
RATE
ORIFICE
SIZE (mm) COLOR MARKING
LF 21,000
LF1 N/A 0.045 None 114N
LF2 N/A 0.045 None 114N
LF3 N/A 0.045 None 114N
LFC N/A 0.025 None 63N
LR 5,000 0.040 White/Purple 101N
CF 9,500 0.0555 Yellow 141N
CR 9,500 0.0555 Yellow 141N
RF 15,000 0.070 Brown 178N
RR 12,000 0.061 Red 155N
PROPANE (LP) CONVERSION INSTRUCTIONS
31-11076-1 05-18 GEA
C2S995, C2S986, C2S900P, and C2S950P
198
III
Denotes 1.98mm Orifice size opening
Denotes Natural Gas
N
Low setting adjustments must be made with other burners in
operation on a medium setting. This procedure prevents the
ORZÀDPHIURPEHLQJVHWWRRORZUHVXOWLQJLQWKHÀDPHEHLQJ
extinguished when other burners are turned on.
A. Turn on all surface burners to medium setting.
% 7XUQWKHNQRERQWKHEXUQHUEHLQJDGMXVWHGWR³/2´
& 5HPRYHWKHNQREDQGLQVHUWDVPDOOÀDWEODGHVFUHZGULYHU
into the valve shaft and/or side adjustment screw(s) as
shown and turn clockwise to fully tighten down the bypass
screw(s). Repeat for all valves.
' ,IÀDPHDSSHDUVWRRORZRUXQVWDEOHVORZO\WXUQE\SDVVVFUHZ
FRXQWHUFORFNZLVHXQWLODVWDEOHÀDPHH[LVWVIRUHDFKEXUQHU
Remember, other burners must be turned on to medium.
SPECIALTY BURNERS
Multi-Ring Burner±7KHRXWHUULQJRIÀDPHVVKRXOGEH
DGMXVWHGZLWKWKHNQREDWWKH0('E\
adjusting the set screw in the center
YDOYHVKDIW7KHÀDPHVVKRXOGEH
adjusted so that they barely curl over
the top edge of the burner cap. The
FHQWHUULQJRIÀDPHVVKRXOGEHDGMXVWHG
with the knob at the LO setting by
adjusting the set screw to the right of
the valve shaft.
( $GGLWLRQDOO\IRUHDFKEXUQHUEHLQJDGMXVWHGTXLFNO\RSHQ
DQGFORVHWKHRYHQGRRUZKLOHREVHUYLQJÀDPH,IÀDPHLV
extinguished, continue adjusting bypass screw for a larger
ÀDPH5HSHDWGRRURSHQLQJVXQWLOÀDPHLVVWDEOH
F. Replace the knob.
Flames
Burner Cap