Install Instructions

ManualsBrandsCadet ManualsHeating, Ventilation, and Air ConditioningPerfectoe Series UC Black Single-Pole Integral 25 Amp Thermostat Kit

INSTALLATION INSTRUCTIONS

Warranty

For more effective and safer operation and to prolong the life of the

heater, read the Owner’s Guide and follow the maintenance instructions.

Failure to properly maintain the heater will void any warranty and may

cause the heater to function improperly. Warranties are non transferable

and apply to original consumer only. Warranty terms are set out below.

LIMITED ONE-YEAR WARRANTY: Cadet will repair or replace any

UCT1 or UCT2 thermostat found to be defective within one year after the

date of purchase.

These warranties do not apply:

1. Damage occurs to the product through improper installation or incor-

rect supply voltage;

2. Damage occurs to the product through improper maintenance, misuse,

abuse, accident, or alteration;

3. The product is serviced by anyone other than Cadet;

4. If the date of manufacture of the product cannot be determined;

5. If the product is damaged during shipping through no fault of Cadet.

6. CADET’S WARRANTY IS LIMITED TO REPAIR OR REPLACEMENT

AS SET OUT HEREIN. CADET SHALL NOT BE LIABLE FOR DAMAGES

SUCH AS PROPERTY DAMAGE OR FOR CONSEQUENTIAL DAMAG-

ES AND/OR INCIDENTAL EXPENSES RESULTING FROM BREACH

OF THESE WRITTEN WARRANTIES OR ANY EXPRESS OR IMPLIED

WARRANTY.

7. IN THE EVENT CADET ELECTS TO REPLACE ANY PART OF YOUR

CADET PRODUCT, THE REPLACEMENT PARTS ARE SUBJECT TO

THE SAME WARRANTIES AS THE PRODUCT. THE INSTALLATION

OF REPLACEMENT PARTS DOES NOT MODIFY OR EXTEND THE

UNDERLYING WARRANTIES. REPLACEMENT OR REPAIR OF ANY

CADET PRODUCT OR PART DOES NOT CREATE ANY NEW WAR-

RANTIES.

8. These warranties give you specic legal rights, and you may also

have other rights which vary from state to state. Cadet neither assumes,

nor authorizes anyone to assume for it, any other obligation or liability in

connection with its products other than as set out herein.

If you believe your Cadet product is defective, please contact Cadet

Manufacturing Co. at 855.CADET.US, during the warranty period, for

instructions on how to have the repair or replacement processed. War-

ranty claims made after the warranty period has expired will be denied.

Products returned without authorization will be refused.

Parts and Service

Visit cadetheat.com/support/parts-service for information on where to

obtain parts and service.

Reduce-Reuse-Recycle

This product is made primarily of recyclable materials. You

can reduce your carbon footprint by recycling this product at

the end of its useful life. Contact your local recycling support

center for further recycling instructions.

For Model UCT1 Single Pole Thermostat (2 wires)

4a. Connect the red thermostat wire to one of the power

supply wires using an insulated wire connector (not

included). See Figure 2.

4b. Connect the black thermostat wire to one heater

wire using an insulated wire connector (not included).

Then connect the remaining power supply wire and the

remaining heater wire using an insulated wire connector

(not included). See Figure 3.

For Model UCT2 Double Pole Thermostat (4 wires)

4a. Connect the two red thermostat wires to each of the

power supply wires using insulated wire connectors (not

included). See Figure 4.

4b. Connect the two black thermostat wires to each of

the two heater wires using insulated wire connectors (not

included). See Figure 5.

1. Remove the heater lid (top cover) from the heater

assembly.

2. Attach the thermostat and bracket assembly to the

inside of the heater as shown in Figure 1. Use the two

screws provided and screw in from the front of the

heater.

3. Proceed with Steps 4a and 4b for model UCT1 or

UCT2, then proceed to Step 5.

1. All electrical work and materials must comply

with the National Electric Code (NEC), the Occu-

pational Safety and Health Act (OSHA), and all

state and local codes.

2. Use copper conductors only.

3. Turn off power to heater circuit at main discon-

nect panel.

4. Connect grounding lead to grounding screw

provided.

5. Make sure all connections are tight and secure, and carefully tuck all wires into the wiring compartment.

6. Remove the plug from the front grill. Install the heater lid and front grill, and complete your heater installation

according to the Perfectoe UC owner’s manual.

7. Install the thermostat knob onto the thermostat shaft extending through the grill. Restore power to the heater.

8. Turn the thermostat knob fully clockwise. When the room reaches your comfort level, turn the knob counterclockwise

until a slight click is heard. The heater will now cycle around this preset temperature. To reduce the room temperature,

turn the knob counterclockwise. To increase the room temperature, turn the knob clockwise.

Figure 1

Figure 2 Figure 3 Figure 4 Figure 5