Warranty

7
More frequently asked questions on our website here: cadetheat.com/support/FAQ
1. Make sure all wires are prop-
erly connected and installation
is complete before you turn on
the heater.
2. Do not operate without grill.
3. Do not tamper with the high-
temperature safety shuto.
How to operate your heater
The room temperature is controlled by a thermostat located either on the wall, or on the heater.
Once installation is complete and power is on, follow the steps below for your thermostat.
If you have a wall or built-in thermostat with a knob:
1. Turn the thermostat knob all the way to the right.
2. When the room reaches your comfort level, turn the knob to the left, just until it clicks and
the heater turns o. The heater will automatically keep the room temperature around this
setting.
3. To reduce the room temperature, turn the knob to the left. To increase the room temperature,
turn the knob to the right.
If you have an electronic wall thermostat, follow the instructions in the programming and operating
guide included with your thermostat.
OPERATING INSTRUCTIONS
Complete installation
After installation, turn your heater to the highest setting and let it run for 30 minutes. Some smoking
may occur as the element initially burns o residue from manufacturing.
If your heater shows signs of overheating, such as glowing red or repeatedly getting unusually hot
and shutting o, immediately turn o the circuit breaker and review the “KNOW YOUR VOLTAGE”
section or call us.
If the high-temperature safety shuto trips more than once a day, replace the heater.
MAINTAINING YOUR HEATER
Clean heater at least every 6 months or as required. Do not lubricate motor.
1. Turn o power at the main disconnect panel.
2. Wait for the heater to cool.
3. Remove thermostat knob (if any) and grill.
4. Wash grill with hot soapy water and dry.
5. Blow air through the heating element with a
hair dryer or shop vacuum on blow cycle.
6. Clean the fan with a vacuum cleaner.
7. Replace grill and thermostat knob (if any).
8. Turn power back on at the main disconnect
panel.
Any service other than cleaning should be performed by an authorized
service representative.
Heating Element
Model CS
High-temperature safety shutoff
Motor
Heater with
built-in thermostat
High-temperature safety shutoff
Model CST
High-temperature safety shutoffHigh-temperature safety shutoff
Heating Element
High-temperature safety shutoff
Heating Element
High-temperature safety shutoff
Motor
Motor
Heater with
built-in thermostat
WITH DOUBLE-POLE WALL
THERMOSTAT ALTERNATE
WITH SINGLE-POLE WALL
THERMOSTAT ALTERNATE
To/From Heater
To/From Heater
Heating Element
Model CS
High-temperature safety shutoff
Motor
Heater with
built-in thermostat
High-temperature safety shutoff
Model CST
High-temperature safety shutoffHigh-temperature safety shutoff
Heating Element
High-temperature safety shutoff
Heating Element
High-temperature safety shutoff
Motor
Motor
Heater with
built-in thermostat
WITH DOUBLE-POLE WALL
THERMOSTAT ALTERNATE
WITH SINGLE-POLE WALL
THERMOSTAT ALTERNATE
To/From Heater
To/From Heater
Heating Element
Model CS
High-temperature safety shutoff
Motor
Heater with
built-in thermostat
High-temperature safety shutoff
Model CST
High-temperature safety shutoffHigh-temperature safety shutoff
Heating Element
High-temperature safety shutoff
Heating Element
High-temperature safety shutoff
Motor
Motor
Heater with
built-in thermostat
WITH DOUBLE-POLE WALL
THERMOSTAT ALTERNATE
WITH SINGLE-POLE WALL
THERMOSTAT ALTERNATE
To/From Heater
To/From Heater
Heating Element
Model CS
High-temperature safety shutoff
Motor
Heater with
built-in thermostat
High-temperature safety shutoff
Model CST
High-temperature safety shutoffHigh-temperature safety shutoff
Heating Element
High-temperature safety shutoff
Heating Element
High-temperature safety shutoff
Motor
Motor
Heater with
built-in thermostat
WITH DOUBLE-POLE WALL
THERMOSTAT ALTERNATE
WITH SINGLE-POLE WALL
THERMOSTAT ALTERNATE
To/From Heater
To/From Heater
INTERNAL HEATER WIRING DIAGRAMS