Manualshelf

Installation Guide

ManualsBrandsCadet ManualsHeating, Ventilation, and Air ConditioningCom-Pak Max Horizontal/Vertical Mount 2,000-Watt 240-Volt Fan-Forced Wall Heater Assembly Only
12345678910
INSTALLATION INSTRUCTIONS (continued)
No change
Disconnect and cut wire with Blue Connector at
Terminal B. Cap loose end with wire connector
or wrap with electrical tape. Move Yellow
Connector from Terminal A to Terminal B.
Disconnect and cut wire with Blue Connector at
Terminal B. Cap loose end with wire connector
or wrap with electrical tape. Move Yellow
Connector from Terminal C to Terminal B.
Cut jumper wire between terminals A and C.
Remove connectors at Terminals B and C.
Move Yellow Connector from Terminal A to
Terminal C. Cap loose ends with wire
connector or wrap with electrical tape.
Cut jumper wire between terminals A and C.
Remove connectors at Terminals B and C.
Cap loose ends with wire connector or wrap
with electrical tape.
D
A
B
C
CM202/CM208
2000
1500
1200
800
500
WIRE CONFIGURATION
DESIRED
WATTAGE
FACTORY SET
AT 2000 WATTS
DO NOT DISCONNECT THE BLUE CONNECTOR FROM TERMINAL “D”
072893E
No change
Disconnect and cut wire with Blue
Connector at Terminal C. Cap loose
end with wire connector or wrap
with electrical tape. Move Yellow
Connector from Terminal B to
Terminal C.
Disconnect and cut wire with Blue
Connector at Terminal C. Cap loose
end with wire connector or wrap
with electrical tape.
CM162/CM168
1600
900
700
WIRE CONFIGURATION
DESIRED W
ATTAGE
FACTORY SET
AT 1600 WATTS
DO NOT DISCONNECT THE BLUE CONNECTOR FROM TERMINAL “A”
072892F
B
C
A
No change
Disconnect and cut wire with Blue
Connector at Terminal C. Cap loose
end with wire connector or wrap
with electrical tape. Move Yellow
Connector from Terminal B to
Terminal C.
Disconnect and cut wire with Blue
Connector at Terminal C. Cap loose
end with wire connector or wrap
with electrical tape.
CM162/CM168
1600
900
700
WIRE CONFIGURATION
DESIRED WATTAGE
FACTORY SET
AT 1600 WATTS
DO NOT DISCONNECT THE BLUE CONNECTOR FROM TERMINAL “A”
072892F
B
C
A
D
A
B
C
R
E
S
E
T
R
E
S
E
T
GRILL
TAB
GRILL
TAB
__________________________
Part Two
__________________________
Figure 4b
Horizontal
Mounting
Figure 4a
Vertical
Mounting
After you have followed all instructions in PART ONE you are ready to install the heater assembly.
Multi-Watt Element Wiring Conguration:
STEP 1
The multi-watt heaters listed below are factory set for the highest possible wattage. If you would like to keep the wattage at the highest
setting, proceed to Step 2. If you would like to reduce your heater’s wattage from the factory setting, refer to the table below that corre-
sponds to your heater model. Once you are nished, proceed to Step 2.
STEP 1
STEP 1
How do I insert the heater assembly into the wall can?
Install Heater Assembly
STEP 2
Install Grill
STEP 3
Secure grill with the screws provided. If you have a built-in thermostat model, slide thermo stat knob onto
shaft. Turn power on at the electrical panel board.
Warranty is void if any material is sprayed on the element or blower. Use a paint mask to cover any exposed
areas of the heater if walls are to be textured or painted.
Turn heater assembly upside down (Element down with motor
facing you). Connect the supply wires to the heater wires with
connectors (See Figure 7). Now rotate the heater so the element
and the fan are facing you.
For VERTICALLY MOUNTED units the element should be at the
top. Insert the bottom edge of the heater assembly into the half
round slots (tabs) in the bottom lip of the wall can (See Figure 8a).
How do I congure my wattage?
For
MODELS
CM162
and
CM168
1600
Watt
Cong-
uration
Shown
(table
above)
For
MODELS
CM202
and
CM208
2000
Watt
Cong-
uration
Shown
(table
above
left)
Figure 7
Figure 8a
Figure 8b
Figure 5a
Figure 5b
Figure 6a
Figure 6b
[IMPORTANT: Push wires into bottom of wall can during insertion. Be sure that supply wires are not caught between motor and wall
can.] Attach assembly at top with screw provided.
For HORIZONTALLY MOUNTED units the element should be to the left. Insert the right edge of the heater assembly into the half round
slots (tabs) on the right side of the wall can (See Figure 8b). [IMPORTANT: Push wires into right side of wall can during insertion. Be
sure that supply wires are not caught between motor and wall can.] Attach assembly at left with screw provided.
DO NOT DISCONNECT THE BLUE CONNECTOR FROM TERMINAL “D” DO NOT DISCONNECT THE BLUE CONNECTOR FROM TERMINAL “A”
Page 4
Supply Wires
Heater
Wires
Top
Motor