Installation Guide

ManualsBrandsCadet Heaters ManualsThermostats KitsCadet Double Pole Field Mount Thermostat Kit for Register Plus Wall Heaters

INSTALLATION INSTRUCTIONS

Warranty

1. All electrical work and materials must comply

with the National Electric Code (NEC), the Occu-

pational Safety and Health Act (OSHA), and all

state and local codes.

2. Use copper conductors only.

3. Turn off power to heater circuit at main discon-

nect panel.

4. Connect grounding lead to grounding screw

provided.

1. Read your Register heater instructions for safety infor-

mation and how to install heater. Set the heater assembly,

blower wheel rst, into the left side of the wall can. Fasten

at top with screw provided.

2. Connect the two black thermostat wires to the two

heater wires. Connect the two red thermostat wires to the

incoming supply wires. (Refer to the wiring diagram on

page 1.)

3. Gently place wires inside wiring compartment area

keeping the wires away from all moving parts.

For more effective and safer operation and to prolong the life of the

heater, read the Owner’s Guide and follow the maintenance instructions.

Failure to properly maintain the heater will void any warranty and may

cause the heater to function improperly. Warranties are non transferable

and apply to original consumer only. Warranty terms are set out below.

LIMITED ONE-YEAR WARRANTY: Cadet will repair or replace any

RMT2 thermostat found to be defective within one year after the date of

purchase.

These warranties do not apply:

1. Damage occurs to the product through improper installation or incor-

rect supply voltage;

2. Damage occurs to the product through improper maintenance, misuse,

abuse, accident, or alteration;

3. The product is serviced by anyone other than Cadet;

4. If the date of manufacture of the product cannot be determined;

5. If the product is damaged during shipping through no fault of Cadet.

6. CADET’S WARRANTY IS LIMITED TO REPAIR OR REPLACEMENT

AS SET OUT HEREIN. CADET SHALL NOT BE LIABLE FOR DAMAGES

SUCH AS PROPERTY DAMAGE OR FOR CONSEQUENTIAL DAMAG-

ES AND/OR INCIDENTAL EXPENSES RESULTING FROM BREACH

OF THESE WRITTEN WARRANTIES OR ANY EXPRESS OR IMPLIED

WARRANTY.

7. IN THE EVENT CADET ELECTS TO REPLACE ANY PART OF YOUR

CADET PRODUCT, THE REPLACEMENT PARTS ARE SUBJECT TO

THE SAME WARRANTIES AS THE PRODUCT. THE INSTALLATION

OF REPLACEMENT PARTS DOES NOT MODIFY OR EXTEND THE

UNDERLYING WARRANTIES. REPLACEMENT OR REPAIR OF ANY

CADET PRODUCT OR PART DOES NOT CREATE ANY NEW WAR-

RANTIES.

8. These warranties give you specic legal rights, and you may also

have other rights which vary from state to state. Cadet neither assumes,

nor authorizes anyone to assume for it, any other obligation or liability in

connection with its products other than as set out herein.

If you believe your Cadet product is defective, please contact Cadet

Manufacturing Co. at 360-693-2505, during the warranty period, for

instructions on how to have the repair or replacement processed. War-

ranty claims made after the warranty period has expired will be denied.

Products returned without authorization will be refused.

Parts and Service

Visit cadetheat.com/parts-service for information on where to obtain parts

and service.

Reduce-Reuse-Recycle

This product is made primarily of recyclable materials. You

can reduce your carbon footprint by recycling this product at

the end of its useful life. Contact your local recycling support

center for further recycling instructions.

6. Align the thermostat face plate so that the four small

tabs slip under the center divider and the rst and third

louvers. Turn the grill over and bend all four tabs to secure

the plate in place.

7. Align the grill so that the thermostat shaft is in the center

of the hole of the face plate. Tighten the grill to the heater

with screws. Press the thermostat knob onto the shaft and

turn fully counter-clockwise.

Figure 1

Figure 2

NOTE: This thermostat is double pole and so has a positive off. If you do not want the heater to come on even when the

climate turns cold, turn the knob fully counterclockwise.

4. Place the bracket/thermostat assembly so that it cap-

tures the bottom edge of the wall can. Fasten the bracket

at the top with the #8 screw provided.

8. Turn on power at the circuit breaker (fuse box) and turn

thermostat knob fully clockwise until temperature is com-

fortable, then turn knob left until a click sound is heard and

the heater turns off. A few adjustments may be necessary

to nd your comfort zone.

5. Holding the grill with labels on top, remove the second

louver from the bottom with needle nose pliers. By bend-

ing the louver back and forth at each end, the louver will

separate from the grill (Figure 2). Important: Only remove

the right side louver.

Page 2