EID-2 Optical Impression Device Operation Manual iTero Mobile Cart Publication SD08300-A Revision 1.05 December 26, 2006 Optical Impression System for Computer Assisted Design and Manufacturing (510K exempt under 21 CFR 872.
EID-2 Optical Impression Device Operation Manual COPYRIGHT Copyright © by Cadent. 1995-2006. All rights reserved. The hardware and software described in this document are supplied under a Sales and Services Agreement and may be used only in accordance with the terms of that agreement. The information contained in this document is subject to change without notice.
Operation Manual EID-2 Optical Impression Device SYMBOLS Caution! - Wherever this symbol appears on the equipment, it is recommended to refer to the instructions in this Operator’s Guide. Applied part type B. Any device on which this symbol appears is electric isolation type B. CLASS 1 LASER COMPLIANCE This product complies with “21 CFR 1040.10” and “EN 60825-1”. MEDICAL SAFETY COMPLIANCE This equipment complies with the medical safety standard UL 60601.
EID-2 Optical Impression Device Operation Manual WARNINGS POWER An internal battery backup unit will supply AC power to the system in the event of a power shortage. Therefore, power is present in the internal hardware components even when the system is unplugged from the wall. To ensure that power is removed from all components, follow these instructions: Close all files and applications. Press the front POWER switch to shutdown the system. Unplug power cable from the wall socket.
Operation Manual EID-2 Optical Impression Device Table of Contents Chapter 1: Introduction .......................................................................................................... 7 Overview ................................................................................................................................ 7 The Digital Crown Production Process ................................................................................... 7 About the iTero Service .......................
EID-2 Optical Impression Device Operation Manual This page is intentionally blank. 6 Publication SD08300-A (Rev. 1.
Operation Manual EID-2 Optical Impression Device Chapter 1: Introduction Overview The EID-2 functions as a digital impression system for scanning preparation teeth in the doctor’s office and uploading the digital files to Cadent for further processing and CNC crown production. This Operator’s Guide explains how to operate the EID-2 system, and also describes the system’s hardware components and features. Chapter 1: Introduction Overview of the iTero digital crown production process.
EID-2 Optical Impression Device Operation Manual About the iTero Service Cadent’s iTero service has introduced to the dental industry a breakthrough technology in the field of digital crown production. The iTero technology makes it possible to perform an intra-oral digital scan in the office and to produce a precise crown based on the digitally acquired data.
Operation Manual EID-2 Optical Impression Device Chapter 2: Operating Instructions This chapter describes the essential operating instructions for working with the EID-2 system. First Time Usage For first-time usage it is essential to boot the EID-2 system at least 24 hours prior to the first case scanning to ensure that the battery backup unit is fully charged.
EID-2 Optical Impression Device Operation Manual Using the iTero Software Once the EID-2 system is up and running, you can use the following iTero applications. The iTero OFFICE application is used for performing 3D color scans of the preparation teeth. The mouse and foot pedals can be used to respond to screen questions during the scanning process. For more information, press F1 to activate the iTero OFFICE help.
Operation Manual EID-2 Optical Impression Device Disinfecting Scanner and Replacing Disposable Sleeve To avoid cross contamination between patients, the scanner must be disinfected and the disposable plastic sleeve must be replaced. First use disinfectant wipes to clean the scanner arm, cradle, keyboard and mouse. Then proceed with the steps below in order to replace the disposable sleeve. STEP 1 Press firmly on both sides of the disposable sleeve to release.
EID-2 Optical Impression Device Operation Manual Using the Foot Pedal Unit USING THE PEDALS The foot pedal unit contains two pedals for activating the scanning sequence and responding to screen questions. The colors of the two foot pedals match the Pedals dialog in the iTero OFFICE application (right is green, left is red). LED INDICATOR Pressing either foot pedal turns on the green LED.
Operation Manual EID-2 Optical Impression Device Chapter 3: Cart Features This chapter describes the external hardware components of the EID-2 system. Front View of Cart Flat LCD monitor can be swiveled freely in any direction. Optical scanner for capturing teeth images. Note that the handheld scanner may be placed in scanner cradle in either direction (right-to-left or left-to-right). POWER switch for performing boot and shutdown. Wireless optical mouse. Built-in keyboard.
EID-2 Optical Impression Device Operation Manual Back View of Cart Air Vent (do not block) Air Vent (do not block) Main AC Power Cable Main Power Shut Off For Shipping or Storage When you need to unplug the cart for an extended period of time, perform these steps: (1) Close all files and applications. (2) Press the front POWER switch to shut down system. (3) Unplug power cable from the wall socket.
Operation Manual EID-2 Optical Impression Device Cleaning Monitor (1) Shut down the system using the front POWER switch to ensure that no power is being supplied to monitor. (2) Lightly dampen a clean white cotton cloth with water and wipe monitor clean. (3) Dry the monitor immediately using a clean white cotton cloth. (4) If further cleaning is necessary, use a clean cloth to wipe off the monitor with a small amount of alcohol. Do not use liquid cleaners, chemicals or aerosol sprays to clean monitor.
EID-2 Optical Impression Device Operation Manual Locking Wheels Each of the four wheels can be locked or unlocked individually. LOCK WHEEL Step down on lever to lock wheel. UNLOCK WHEEL Raise lever to unlock wheel. 16 Publication SD08300-A (Rev. 1.
Operation Manual EID-2 Optical Impression Device Appendix A: Hardware Specifications ITEM DESCRIPTION Monitor LCD 19” monitor meets FCC and safety approval (UL, CSA, TUV) and operates at 1280x1024 resolution. Handheld Scanner Emits red laser light for performing tooth scan (660 nm Class 1). Also emits colored lights for performing a colored scan. Battery Backup Unit Wireless LAN APC® Back-UPS® ES 725 Broadband DWL-G122™ Wireless USB Adapter produced by D-LINK®. The DWL-G122 provides 2.