Specifications

ManualsBrandsCADDX ManualsMusical equipmentNX-408E-I

NX1700EIG05

(Supercedes NX1700EIF04)

NX-1700E Proximity Card Reader

Installation and Startup

NetworX

™

is a trademark of the GE Security companies.

These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to be met during installation,

operation, and maintenance. If further information is desired or if particular problems arise that are not covered sufficiently for the purchaser’s purpose, the

matter should be referred to GE Security, Gladewater, Texas, USA.

This document contains proprietary information of GE Security, USA and is furnished to its customer solely to assist that customer in the installation, testing,

operations, and/or maintenance of the equipment described. This document shall not be reproduced in whole or in part nor shall its contents be disclosed to

any third party without the written approval of GE Security.

Please refer to the current GE Security product catalog for detailed warranty information.

Main 800-727-2339 Technical Support 888-437-3287

Outside the US 903-845-6941 Sales & Literature 800-547-2556

Main Fax 903-845-6811 Web: www.caddx.com

www.gesecurity.com

Symbol Legend

Warning

Indicates a procedure, practice, condition, or statement that, if not strictly observed, could result in personal injury.

* This symbol indicates electrical warnings and cautions.

Caution

Indicates a procedure, practice, condition, or statement that, if not strictly observed, could result in damage to or

destruction of equipment or property.

** This symbol indicates general warnings and cautions.



Note

Indicates an essential or important procedure, instruction, condition, or statement.



Tip

Indicates a user tip. Provides helpful information that is not normally defined in regular use, but from an experienced

user.

Enter

Indicates a key or button should be pressed to enter data.

ORDERING INFORMATION

PART #

DESCRIPTION PART # DESCRIPTION

NX-1700E Card Reader Module NX-216E 16 Zone Expander Module

NX-8E 8 – 192 Zone Control Only NX-320E Smart Power Supply and Buss Extender

NX-848E-KIT NX-8E Control, NX-148E LCD Keypad, 40VA Transformer NX-408E  8 Zone Wireless Expansion Module

NX-8 8 – 48 Zone Control Only NX-416E  16 Zone Wireless Expansion Module

NX-848-KIT NX-8 Control, NX-148E LCD Keypad, 40VA Transformer NX-448E  48 Zone Wireless Expansion Module

NX-6 6 – 12 Zone Control Only NX-507E Seven Relay Module

NX-648-KIT NX-6 Control, NX-148E LCD Keypad, 40VA Transformer NX-508E Eight Output Module

NX-148E Alphanumeric 48 Zone LCD Keypad NX-534E Two-Way Listen In Module

NX-1192E 192 Zone LCD Keypad

 These units are UL listed for residential use only.

Summary of content (16 pages)

PAGE 1
NX1700EIG05 (Supercedes NX1700EIF04) NX-1700E Proximity Card Reader Installation and Startup © 2005 GE Security All rights reserved. Printed in the United States of America. NetworX™ is a trademark of the GE Security companies. These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to be met during installation, operation, and maintenance.
PAGE 2
TABLE OF CONTENTS I. GENERAL DESCRIPTION.................................................................................................................................................................................. 3 II. INSTALLATION AND WIRING.......................................................................................................................................................................... 3 III. ENROLLING .......................................................................
PAGE 3
GENERAL DESCRIPTION I. The NetworX NX-1700E is a proximity card reader / door control module used to expand the capabilities of the NetworX control panels.
PAGE 4
PROGRAMMING V. A. USING THE LED KEYPAD NOTE: The NX-108E / NX-116E / NX-124E series keypads should not be used to program user cards. ACTION RESULT ENTERING THE PROGRAM MODE &Á_ & [Go To Program Code] Factory Default is `^XZ xxxxxxxx Enters the Program Mode. Stay, Chime, Exit, Bypass & Cancel LEDS will flash. xxxxxxxx If the "Go To Program Code" is valid, the "Service" LED will flash and the 5 function LEDs will illuminate steady.
PAGE 5
EXITING THE PROGRAM MODE: & EXIT EXIT xxxxxxxx Exits this programming level. B. USING THE LCD KEYPAD All steps required for programming are the same as the aforementioned LED keypad. The LCD keypad display will prompt you for the data required. While in the programming mode, and not in a location, the number in parenthesis is the location you were previously changing. For example, if the display reads "Enter location, then # (5)", it is reminding you that location 5 was the last location you programmed.
PAGE 6
ADDING ONE USER ACTION & [STAY] & [3-digit user number] Example: or W W XY[ XY[ RESULT xxxxxxxx Accesses Activation mode xxxxxxxx If a valid user number is entered, LED1 on any enabled readers will begin to flash. if 4-digit user code if 6-digit user codes Scan the card designated for the user entered in the previous step. xxxxxxxx 1) 2) If the user card is not already in the system, it will be added and mapped to the entered user number and LED1 will flash.
PAGE 7
DE-ACTIVATE ONE USER ACTION & [BYPASS] & [3-digit user number] RESULT xxxxxxxx Accesses De-activation mode xxxxxxxx If a valid user number is entered, LED1 on any enabled readers will begin to flash. xxxxxxxx The card information for the user entered in the previous step will be cleared, and LED1 will stop flashing. After about 30 seconds, all the readers in the system will be updated.
PAGE 8
Segment 2 Double Scan Function {Double Beep} Program the functions that are performed when a card is scanned twice within the 2 Scan Hold Time {two beeps}. Location 244, Segment 1 programs the length of time between beeps. The descriptions of the options are the same as for Single Beep Scan Function. Default is 1. Segment 3 Single Scan Hold Function {Triple Beep} Program the functions that are performed when a card is scanned and held at the reader for the duration of the 2 Scan Hold Time {three beeps}.
PAGE 9
Segment 2 LED1 (Green) Options: "On" to follow Ready status of system. (Default is “On”) "On" to toggle with the open collector output activation. (Default is “On”) "On" if inverted. Reserved. Segment 3 LED2 (Red) Options: "On" to follow Armed status of system. (Default is “On”) "On" to toggle with the open collector output activation. "On" if inverted. Reserved. Segment 4 Reader Partition: "On" if reader is in Partition 1. "On" if reader is in Partition 2. "On" if reader is in Partition 3.
PAGE 10
LOCATION 246 PROGRAMMING THE ACCESS OPTIONS (2 segments of binary data) Segment 1 Door Options LED1 - "On" if locking mechanism is a Maglock or Drop Bolt. LED2 - "On" if access is allowed regardless of Armed status of the system. LED3 - "On" if the door is not to be latched unlocked during an open schedule. LED4 - "On" if onboard open collector output only triggers during an open schedule. LED5 - “On” if onboard open collector output only triggers during a close schedule.
PAGE 11
LOCATION 271 PROGRAMMING THE DATE OF HOLIDAYS IN JANUARY (8 segments of numerical data) Program the day of the month in January that the Opening time in a schedule is suppressed. For example, if the opening should not occur on January 1, program a “1” in Segment 1. This feature can be repeated up to a maximum of 8 holidays per location (month).
PAGE 12
VIII. PROGRAMMING WORKSHEETS IMPORTANT TIP: Defaults are shown in bold italics. LOC 0 PG 7 1-240 241 8 8 DESCRIPTION DEFAULT SCAN FUNCTIONS Seg 1 SINGLE SCAN FUNCTION (1 Beep) 8 1 = "On" to send Code Entry function to the control panel. 2 = "On" to activate the Armed Away mode. 3 = "On" to activate the Armed Stay mode. 4 = "On" to send the Disarm function to the control panel. 5 = "On" to send Auxiliary Function #1 to the control panel. 6 = "On" to send Auxiliary Function #2 to the control panel.
PAGE 13
LOC 242 PG 8 243 9 244 9 245 9 246 10 247 10 248 10 249 10 250 10 251 10 DESCRIPTION DEFAULT YOUR DATA LED2 (RED) OPTIONS 1 1 = "On" follows system Armed status 2 = "On" to toggle with the Open Collector output 3 = "On" if inverted 4-8= Reserved.
PAGE 14
LOC 252 PG 10 253 10 254 255 10 256 10 257 10 258 10 259 10 260 10 261 10 262 10 263 264 14 10 10 10 DESCRIPTION DAYS FOR SCHEDULE 2 1 = "On" if schedule is active on Sunday. 2 = "On" if schedule is active on Monday. 3 = "On" if schedule is active on Tuesday. 4 = "On" if schedule is active on Wednesday. 5 = “On” if schedule is active on Thursday. 6 = “On” if schedule is active on Friday. 7 = “On” if schedule is active on Saturday. 8 = “On” if schedule is disabled on holidays.
PAGE 15
LOC 265 266 PG 10 10 267 10 268 10 269 10 270 10 271 272 273 274 275 276 277 278 279 280 281 282 283 11 11 11 11 11 11 11 11 11 11 11 11 11 284 11 285 11 DESCRIPTION OPENING TIME FOR SCHEDULE 7 Seg 1 Hour of Opening Time (24-hr format) Seg 2 Minutes after Hour of Opening CLOSING TIME FOR SCHEDULE 7 Seg 1 Hour of Closing Time (24-hr format) Seg 2 Minutes after Hour of Closing DAYS FOR SCHEDULE 7 1 = "On" if schedule is active on Sunday. 2 = "On" if schedule is active on Monday.
PAGE 16
IX. GLOSSARY DESCRIPTION TERM Alternative Mode Alternative mode is an optional scan method, as opposed to the default Legacy mode (see below). The card is to be continuously held at the reader for a specified number of beeps. Example: Hold the card at the card reader’s sensor for a total of 2 beeps. This is a “double beep” in the Alternative mode. This method becomes available when Location 272, Segment 1, Option 6 is disabled. Double Beep………………. An audible indicator (beep, beep). Double Beep Scan……….