00 Series Industrial Grade USB Flash Drive (UFD) Product Manual Cactus Technologies Limited Suite C, 15/F, Capital Trade Center 62 Tsun Yip Street, Kwun Tong Kowloon, Hong Kong Tel: +852-2797-2277 Email: sales@cactus-tech.com Cactus USA 3112 Windsor Road Suite A356 Austin, Texas 78703 Tel: +512-775-0746 Email: americas@cactus-tech.com Cactus-Tech.
The information in this manual is believed to be accurate at the time of publication but is subject to change without notice. Cactus Technologies® Limited shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material.
CONTENTS Table of 1 . Introduction to Cactus Technologies 100 Series Industrial Grade UFD Products ...................................................................................... 1 1.1.Supported Standards..................................................................................................................... 2 1.2.Product Features............................................................................................................................ 2 1.2.1.
01 Introduction to Cactus Technologies 100 Series Industrial Grade UFD Products Features • Solid state design with no moving parts • Plugs into industry standard USB-A receptacles • Compliant with USB2.0 specifications • Compliant with USB Mass Storage Class specifications v1.0 • High reliability, MTBF > 6,500,000 hrs.
1.1. Supported Standards Cactus Technologies® UFD is fully electrically compatible with the following specification: • USB2.0 Specification published by the USB Implementor's Forum 1.2. Product Features Cactus Technologies® Industrial UFD contains a high level, intelligent controller. This intelligent controller provides many capabilities including the following: • USB command processing.
1.2.3. Intelligent Power Management Cactus Technologies® Industrial UFD employs sophisticated static, dynamic and global wear leveling algorithms and intelligent bad block management to ensure high data reliability and to maximize product life. Cactus Technologies® 100 Series Industrial Grade UFD Product Manual v2.
02 Power Supply Requirements Cactus Technologies Industrial DOM is a dual voltage product, which means it will operate at a voltage range of 3.30 volts ±10% or 5.00 volts ± 10%.Product Specifications For all the following specifications, values are defined at ambient temperature and nominal supply voltage unless otherwise stated. 2.1. System Environmental Specifications Cactus Industrial UFD Table 2-1.
2.3. System Performance All performance numbers are typical values assuming the card controller is in the default (i.e., fastest) mode. Table 2-3. Performance Read Transfer Rate up to 33.0 Mbytes/sec* Write Transfer Rate up to 26.0 Mbytes/sec * 2.4. System Reliability Table 2-4. Reliability MTBF (@ 25°C) >6,500,000 hours Data Reliability <1 non-recoverable error in 1014 bits READ Endurance: >2,000,000 erase/program cycles 2.5.
2.5.1. UFD Physical Specifications Refer to Figure 2-1 for Cactus 40-pin DOM physical specifications and dimensions and Figure 2-2 for Cactus 44-pin DOM physical specifications. Cactus Technologies® 100 Series Industrial Grade UFD Product Manual v2.
2.6. Capacity Specifications Cactus Technologies® UFD product is offered in capacities of 128MByte, 256MByte, 512MByte, 1GByte, 2GByte, 4GByte or 8 GByte. Cactus Technologies® 100 Series Industrial Grade UFD Product Manual v2.
03 Interface Description The following sections provide detailed information on the Cactus Technologies® Industrial UFD interface. 3.1. Electrical Specification The following table defines all D.C. Characteristics for the UFD. Unless otherwise stated, conditions are: Vcc = 5V ± 10% Ta = 0°C to 70°C 3.1.1. Absolute Maximum Ratings Parameter Symbol MIN MAX Units Storage Temperature Ts -55 150 oC Operating Temperature TA- -45 90 oC Vcc with respect to GND Vcc -0.3 6.
Parameter Symbol MIN MAX Output Levels USB D+, D-, High Speed Mode Low High VOL VOH -10 360 10 440 Operating Current Suspend Active Cactus Technologies® ICC 2,5 200 Units mV mA 100 Series Industrial Grade UFD Product Manual v2.
Appendix A Ordering Information Model KUXRY-100 Where X is card capacities: 128M.........................................................................................................................128MB 256M ........................................................................................................................256MB 512M ....................................................................................................................... 512MB 1G .....................................
Appendix B Technical Support Services Cactus Technologies® Limited Suite C, 15/F, Capital Trade Center 62 Tsun Yip Street, Kwun Tong Kowloon, Hong Kong Tel: +852-27972261 Fax: +852-27973777 Email: tech@cactus-tech.com Cactus Technologies® Limited Santa Clara, CA 95054 Email: tech@cactus-tech.com Cactus Technologies® 100 Series Industrial Grade UFD Product Manual v2.
Appendix C Cactus Technologies debra.park2 debra.park2zz z vzv v z Offices v Worldwide Sales ® z Cactus Technologies® Limited Suite C, 15/F, Capital Trade Center 62 Tsun Yip Street, Kwun Tong Kowloon, Hong Kong Tel: +852-27972277 Fax: +852-27973777 Email: sales@cactus-tech.com Cactus® USA 3112 Windsor Road Suite A-356 Austin, Texas Tel: +512-775-0746 Email: americas@cactus-tech.com Cactus Technologies® 100 Series Industrial Grade UFD Product Manual v2.
Appendix D Limited Warranty I. WARRANTY STATEMENT Cactus Technologies® warrants its Industrial Grade products only to be free of any defects in materials or workmanship that would prevent them from functioning properly for five years from the date of purchase. This express warranty is extended by Cactus Technologies® Limited II. GENERAL PROVISIONS This warranty sets forth the full extent of Cactus Technologies®' responsibilities regarding the Cactus Industrial Grade Flash Storage products.
shall be tested to the product s functional and performance specifications. Upon confirmation of failure, each product will be analyzed, by whatever means necessary, to determine the root cause of failure. If the root cause of failure is found to be not covered by the above provisions, then the product will be returned to the customer with a report indicating why the failure was not covered under the warranty.
