Specifications
Table Of Contents
- Title Page
- Notice
- Contents
- acl Commands
- acl-edit Commands
- aging Commands
- arp Commands
- cli Commands
- configure Command
- copy Command
- dvmrp Commands
- enable Command
- erase Command
- exit Command
- file Commands
- filters Commands
- http Commands
- igmp Commands
- interface Commands
- ip Commands
- ip-router Commands
- Command Summary
- ip-router authentication add key-chain
- ip-router authentication create key-chain
- ip-router global add
- ip-router global set
- ip-router global set trace-options
- ip-router global set trace-state
- ip-router global use provided_config
- ip-router kernel trace
- ip-router policy add filter
- ip-router policy add optional-attributes-list
- ip-router policy aggr-gen destination
- ip-router policy create aggregate-export-source
- ip-router policy create aggr-gen-dest
- ip-router policy create aggr-gen-source
- ip-router policy create aspath-export-source
- ip-router policy create bgp-export-destination
- ip-router policy create bgp-export-source
- ip-router policy create bgp-import-source
- ip-router policy create direct-export-source
- ip-router policy create filter
- ip-router policy create optional-attributes-list
- ip-router policy create ospf-export-destination
- ip-router policy create ospf-export-source
- ip-router policy create ospf-import-source
- ip-router policy create rip-export-destination
- ip-router policy create rip-export-source
- ip-router policy create rip-import-source
- ip-router policy create static-export-source
- ip-router policy create tag-export-source
- ip-router policy export destination
- ip-router policy import source
- ip-router policy redistribute
- ip-router show configuration file
- ip-router show state
- ipx Commands
- l2-tables Commands
- logout Command
- multicast Commands
- mtrace Command
- negate Command
- no Command
- ospf Commands
- Command Summary
- ospf add interface
- ospf add nbma-neighbor
- ospf add network
- ospf add stub-host
- ospf add virtual-link
- ospf create area
- ospf create-monitor
- ospf monitor
- ospf set area
- ospf set ase-defaults
- ospf set export-interval
- ospf set export-limit
- ospf set interface
- ospf set monitor-auth-method
- ospf set trace-options
- ospf set virtual-link
- ospf show
- ospf start|stop
- ping Command
- port Commands
- qos Commands
- reboot Command
- rip Commands
- save Command
- show Command
- snmp Commands
- statistics Commands
- stp Commands
- system Commands
- Command Summary
- system image add
- system image choose
- system image delete
- system image list
- system promimage upgrade
- system set bootprom
- system set contact
- system set date
- system set dns
- system set location
- system set name
- system set password
- system set poweron-selftest
- system set syslog
- system set terminal
- system show
- traceroute Command
- vlan Commands
Chapter 13: filters Commands
SSR Command Line Interface Reference Manual 13 - 3
filters add address-filter
Purpose
Applies an address filter.
Format
filters add address-filter name
<name>
source-mac
<MACaddr>
dest-mac
<MACaddr>
vlan
<VLAN-num>
in-port-list
<port-list>
Mode
Configure
Description
The
filters
add
address-filter
command blocks traffic based on a frame’s
source MAC address (
source-mac
), destination MAC address (
dest-mac
), or a flow
(specified using both a source MAC address and a destination MAC address).
Parameters
name
<name>
Specifies the name of the filter.
source-mac
<MACaddr>
Specifies the source MAC address. Use this op-
tion for source or flow address filters.
dest-mac
<MACaddr>
Specifies the destination MAC address. Use
this option for destination or flow static entries.
vlan
<VLAN-num>
Specifies the VLAN.
in-port-list
<port-list>
Specifies the ports to which you want to apply
the filter.
Restrictions
You should apply flow filters (specified using both a source MAC address and a
destination MAC address) only to ports that are using flow-based bridging.