Specifications
Table Of Contents
- Title Page
- Notice
- Contents
- acl Commands
- acl-edit Commands
- aging Commands
- arp Commands
- cli Commands
- configure Command
- copy Command
- dvmrp Commands
- enable Command
- erase Command
- exit Command
- file Commands
- filters Commands
- http Commands
- igmp Commands
- interface Commands
- ip Commands
- ip-router Commands
- Command Summary
- ip-router authentication add key-chain
- ip-router authentication create key-chain
- ip-router global add
- ip-router global set
- ip-router global set trace-options
- ip-router global set trace-state
- ip-router global use provided_config
- ip-router kernel trace
- ip-router policy add filter
- ip-router policy add optional-attributes-list
- ip-router policy aggr-gen destination
- ip-router policy create aggregate-export-source
- ip-router policy create aggr-gen-dest
- ip-router policy create aggr-gen-source
- ip-router policy create aspath-export-source
- ip-router policy create bgp-export-destination
- ip-router policy create bgp-export-source
- ip-router policy create bgp-import-source
- ip-router policy create direct-export-source
- ip-router policy create filter
- ip-router policy create optional-attributes-list
- ip-router policy create ospf-export-destination
- ip-router policy create ospf-export-source
- ip-router policy create ospf-import-source
- ip-router policy create rip-export-destination
- ip-router policy create rip-export-source
- ip-router policy create rip-import-source
- ip-router policy create static-export-source
- ip-router policy create tag-export-source
- ip-router policy export destination
- ip-router policy import source
- ip-router policy redistribute
- ip-router show configuration file
- ip-router show state
- ipx Commands
- l2-tables Commands
- logout Command
- multicast Commands
- mtrace Command
- negate Command
- no Command
- ospf Commands
- Command Summary
- ospf add interface
- ospf add nbma-neighbor
- ospf add network
- ospf add stub-host
- ospf add virtual-link
- ospf create area
- ospf create-monitor
- ospf monitor
- ospf set area
- ospf set ase-defaults
- ospf set export-interval
- ospf set export-limit
- ospf set interface
- ospf set monitor-auth-method
- ospf set trace-options
- ospf set virtual-link
- ospf show
- ospf start|stop
- ping Command
- port Commands
- qos Commands
- reboot Command
- rip Commands
- save Command
- show Command
- snmp Commands
- statistics Commands
- stp Commands
- system Commands
- Command Summary
- system image add
- system image choose
- system image delete
- system image list
- system promimage upgrade
- system set bootprom
- system set contact
- system set date
- system set dns
- system set location
- system set name
- system set password
- system set poweron-selftest
- system set syslog
- system set terminal
- system show
- traceroute Command
- vlan Commands
Chapter 8: dvmrp Commands
SSR Command Line Interface Reference Manual 8 - 5
dvmrp set interface
Purpose
Configure various DVMRP parameters on an interface.
Format
dvmrp set interface
<ipAddr>
|
<hostname>
[
metric
<num>
]
[neighbor-timeout
<seconds>
] [prunetime
<seconds>
] [
rate
<num>
]
[scope
<num>
] [
threshold
<num>
]
Mode
Configure
Description
The
dvmrp
set
interface
command sets DVMRP parameters on an IP interface.
Parameters
<ipAddr>
|
<hostname>
IP address or hostname of the interface on which you
are configuring DVMRP parameters.
metric
<num>
The metric (cost) of this interface. Specify a number in
the range 1 – 16.
neighbor-timeout
<num>
The number of seconds after which the SSR will con-
sider the neighbor to be down. Specify a number in the
range 40 – 400. The default is 35.
Note:
If you have some old routers, this value
should be increased to accommodate them
because they don't have to send routing
updates at 40-second intervals.
prunetime
<seconds>
The multicast prunetime of this interface. Specify a
number in the range 300 – 7200. The default is 3600
(one hour).
rate
<num>
The multicast rate of this interface in kbps. Specify a
number in the range 1 – 10000. The default is 500.
Note:
The option applies only to tunnels.
scope
<IPaddr/mask>
The multicast scope of this interface. The purpose of
this option is to disallow the groups specified by a