Specifications
Table Of Contents
- Title Page
- Notice
- Contents
- acl Commands
- acl-edit Commands
- aging Commands
- arp Commands
- cli Commands
- configure Command
- copy Command
- dvmrp Commands
- enable Command
- erase Command
- exit Command
- file Commands
- filters Commands
- http Commands
- igmp Commands
- interface Commands
- ip Commands
- ip-router Commands
- Command Summary
- ip-router authentication add key-chain
- ip-router authentication create key-chain
- ip-router global add
- ip-router global set
- ip-router global set trace-options
- ip-router global set trace-state
- ip-router global use provided_config
- ip-router kernel trace
- ip-router policy add filter
- ip-router policy add optional-attributes-list
- ip-router policy aggr-gen destination
- ip-router policy create aggregate-export-source
- ip-router policy create aggr-gen-dest
- ip-router policy create aggr-gen-source
- ip-router policy create aspath-export-source
- ip-router policy create bgp-export-destination
- ip-router policy create bgp-export-source
- ip-router policy create bgp-import-source
- ip-router policy create direct-export-source
- ip-router policy create filter
- ip-router policy create optional-attributes-list
- ip-router policy create ospf-export-destination
- ip-router policy create ospf-export-source
- ip-router policy create ospf-import-source
- ip-router policy create rip-export-destination
- ip-router policy create rip-export-source
- ip-router policy create rip-import-source
- ip-router policy create static-export-source
- ip-router policy create tag-export-source
- ip-router policy export destination
- ip-router policy import source
- ip-router policy redistribute
- ip-router show configuration file
- ip-router show state
- ipx Commands
- l2-tables Commands
- logout Command
- multicast Commands
- mtrace Command
- negate Command
- no Command
- ospf Commands
- Command Summary
- ospf add interface
- ospf add nbma-neighbor
- ospf add network
- ospf add stub-host
- ospf add virtual-link
- ospf create area
- ospf create-monitor
- ospf monitor
- ospf set area
- ospf set ase-defaults
- ospf set export-interval
- ospf set export-limit
- ospf set interface
- ospf set monitor-auth-method
- ospf set trace-options
- ospf set virtual-link
- ospf show
- ospf start|stop
- ping Command
- port Commands
- qos Commands
- reboot Command
- rip Commands
- save Command
- show Command
- snmp Commands
- statistics Commands
- stp Commands
- system Commands
- Command Summary
- system image add
- system image choose
- system image delete
- system image list
- system promimage upgrade
- system set bootprom
- system set contact
- system set date
- system set dns
- system set location
- system set name
- system set password
- system set poweron-selftest
- system set syslog
- system set terminal
- system show
- traceroute Command
- vlan Commands
Chapter 28: port Commands
28 - 6 SSR Command Line Interface Reference Manual
Restrictions
Note the following restrictions:
• Unless you are mirroring the traffic form the Control Module, you must specify
either an input port or an output slot.
• You cannot specify the
any
keyword with both the
traffic-from
and
traffic-to
options at the same time.
• None of the ports on the slot containing the protocol analyzer port can send or
receive traffic while port mirroring is taking place. When a port is selected to receive
mirrored traffic, none of the other ports on the line card can be used for normal traf-
fic. For this reason, the protocol analyzer port cannot be on the same slot (line card)
as the mirrored port(s).
• Do not configure an interface on the protocol analyzer port.
Examples
Here are some examples of port mirroring commands.
ssr(config)# port mirroring to et.1.1 traffic-from et.3.1 traffic-to any
Copies traffic coming from port et.3.1 and going to any slot. The copied traffic is
sent to port et.1.1, to which the protocol analyzer is attached.
ssr(config)# port mirroring to et.1.1 traffic-from any traffic-to 4
Copies traffic coming from any port and going to slot 4. The copied traffic is sent
to port et.1.1, to which the protocol analyzer is attached.
ssr(config)# port mirroring to et.1.1 cpu-port-traffic
Captures all traffic going to and from the Control Module. The copied traffic is
sent to port et.1.1, to which the protocol analyzer is attached.