Specifications
Table Of Contents
- Title Page
- Notice
- Contents
- acl Commands
- acl-edit Commands
- aging Commands
- arp Commands
- cli Commands
- configure Command
- copy Command
- dvmrp Commands
- enable Command
- erase Command
- exit Command
- file Commands
- filters Commands
- http Commands
- igmp Commands
- interface Commands
- ip Commands
- ip-router Commands
- Command Summary
- ip-router authentication add key-chain
- ip-router authentication create key-chain
- ip-router global add
- ip-router global set
- ip-router global set trace-options
- ip-router global set trace-state
- ip-router global use provided_config
- ip-router kernel trace
- ip-router policy add filter
- ip-router policy add optional-attributes-list
- ip-router policy aggr-gen destination
- ip-router policy create aggregate-export-source
- ip-router policy create aggr-gen-dest
- ip-router policy create aggr-gen-source
- ip-router policy create aspath-export-source
- ip-router policy create bgp-export-destination
- ip-router policy create bgp-export-source
- ip-router policy create bgp-import-source
- ip-router policy create direct-export-source
- ip-router policy create filter
- ip-router policy create optional-attributes-list
- ip-router policy create ospf-export-destination
- ip-router policy create ospf-export-source
- ip-router policy create ospf-import-source
- ip-router policy create rip-export-destination
- ip-router policy create rip-export-source
- ip-router policy create rip-import-source
- ip-router policy create static-export-source
- ip-router policy create tag-export-source
- ip-router policy export destination
- ip-router policy import source
- ip-router policy redistribute
- ip-router show configuration file
- ip-router show state
- ipx Commands
- l2-tables Commands
- logout Command
- multicast Commands
- mtrace Command
- negate Command
- no Command
- ospf Commands
- Command Summary
- ospf add interface
- ospf add nbma-neighbor
- ospf add network
- ospf add stub-host
- ospf add virtual-link
- ospf create area
- ospf create-monitor
- ospf monitor
- ospf set area
- ospf set ase-defaults
- ospf set export-interval
- ospf set export-limit
- ospf set interface
- ospf set monitor-auth-method
- ospf set trace-options
- ospf set virtual-link
- ospf show
- ospf start|stop
- ping Command
- port Commands
- qos Commands
- reboot Command
- rip Commands
- save Command
- show Command
- snmp Commands
- statistics Commands
- stp Commands
- system Commands
- Command Summary
- system image add
- system image choose
- system image delete
- system image list
- system promimage upgrade
- system set bootprom
- system set contact
- system set date
- system set dns
- system set location
- system set name
- system set password
- system set poweron-selftest
- system set syslog
- system set terminal
- system show
- traceroute Command
- vlan Commands
Chapter 20: l2-tables Commands
20 - 10 SSR Command Line Interface Reference Manual
l2-tables show vlan-igmp-status
Purpose
Show whether IGMP is on or off on a VLAN.
Format
l2-tables show vlan-igmp-status
vlan
<VLAN-num>
Mode
Enable
Description
The
l2-tables show vlan-igmp-status
command shows the multicast MAC
addresses that IGMP has registered with the L2 tables. This command also shows the
ports to which the multicast MAC addresses are forwarded.
Note:
For IGMP forwarding to occur for a multicast MAC address, IGMP must
be enabled on the VLAN with which the MAC address is associated.
Parameters
vlan
<VLAN-num>
The VLAN number. The VLAN number can be
from 1 – 4095.
Restrictions
None.