Title Page HSIM-SSR-600 Installation Guide SPD/100 XMT RCV CPU 9033040-01 HSIM-SSR-600 10/100
Only qualified personnel should perform installation procedures. NOTICE Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made. The hardware, firmware, or software described in this manual is subject to change without notice.
Notice INDUSTRY CANADA NOTICE This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.
Notice CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT IMPORTANT: THIS LICENSE APPLIES FOR USE OF PRODUCT IN THE FOLLOWING GEOGRAPHICAL REGIONS: CANADA MEXICO CENTRAL AMERICA SOUTH AMERICA BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT, CAREFULLY READ THIS LICENSE AGREEMENT. This document is an agreement (“Agreement”) between You, the end user, and Cabletron Systems, Inc.
Notice If the Program is exported from the United States pursuant to the License Exception TSR under the U.S.
Notice CABLETRON SYSTEMS SALES AND SERVICE, INC. PROGRAM LICENSE AGREEMENT IMPORTANT: THIS LICENSE APPLIES FOR USE OF PRODUCT IN THE UNITED STATES OF AMERICA AND BY UNITED STATES OF AMERICA GOVERNMENT END USERS. BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT, CAREFULLY READ THIS LICENSE AGREEMENT. This document is an agreement (“Agreement”) between You, the end user, and Cabletron Systems Sales and Service, Inc.
Notice If the Program is exported from the United States pursuant to the License Exception TSR under the U.S.
Notice CABLETRON SYSTEMS LIMITED PROGRAM LICENSE AGREEMENT IMPORTANT: THIS LICENSE APPLIES FOR THE USE OF THE PRODUCT IN THE FOLLOWING GEOGRAPHICAL REGIONS: EUROPE MIDDLE EAST AFRICA ASIA AUSTRALIA PACIFIC RIM BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT, CAREFULLY READ THIS LICENSE AGREEMENT.
Notice If the Program is exported from the United States pursuant to the License Exception TSR under the U.S.
Notice DECLARATION OF CONFORMITY Application of Council Directive(s): Manufacturer’s Name: Manufacturer’s Address: European Representative Name: European Representative Address: Conformance to Directive(s)/Product Standards: Equipment Type/Environment: 89/336/EEC 73/23/EEC Cabletron Systems, Inc. 35 Industrial Way PO Box 5005 Rochester, NH 03867 Mr. J.
Notice x HSIM-SSR-600 Installation Guide
CONTENTS Figures ................................................................................................... xiii Tables..................................................................................................... xiv INTRODUCTION Using This Guide ...........................................................................xv Structure of This Guide................................................................. xvi HSIM-SSR-600 Features........................................................
Contents CHAPTER 3 3.1 3.2 3.3 3.4 3.5 TROUBLESHOOTING, SWITCHES, AND LED INDICATIONS Front Panel LED Indications ........................................................3-2 Console Management/Ethernet Port............................................3-3 Switches.......................................................................................3-3 3.3.1 Switch Function Procedure .............................................3-4 Troubleshooting HSIM-SSR-600 Hardware .................................
FIGURES Figure 2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 2-9 3-1 3-2 Page SSR-600-ECM Installation Area............................................... 2-3 WAN SWPIM Ports .................................................................. 2-4 Removing an Existing SWPIM ................................................. 2-4 Removing the HSIM Coverplate............................................... 2-5 Installing the HSIM-SSR-600 ...................................................
TABLES Table 3-1 3-2 A-1 A-2 Page HSIM-SSR-600 LAN LEDs....................................................... 3-2 Four-Position Switch Functions ............................................... 3-4 Fast Ethernet / Console Port Connector Pinout .......................A-1 Cable Adapter Pinout (Part Number 9360222) ........................
INTRODUCTION Only qualified personnel should perform installation procedures. Welcome to the Cabletron Systems HSIM-SSR-600 Installation Guide. HSIM stands for High Speed Interface Module, and SSR stands for SmartSwitch Router. This guide provides installation, basic configuration information, hardware specifications and troubleshooting tips for the HSIM-SSR-600. The HSIM-SSR-600 is a module that can be installed into a host platform.
Introduction STRUCTURE OF THIS GUIDE This guide is organized as follows: This Introduction provides preliminary information that will aid in using this manual. It lists technology and user’s guides that may help the user to set up and manage the HSIM-SSR-600, and provides an overview of the HSIM-SSR-600 and its features, and provides instructions on how to get help from Cabletron Systems.
Introduction OPTIONAL FEATURES Optional features for the HSIM-SSR-600 include the SSR-600-ECM auxiliary card, which performs encryption or compression, and the SWPIMs (Sliding WAN Physical Interface Modules), listed below. • The SWPIM-T1 provides a T1 interface through a front panel RJ45 port and includes a built-in Channel Service Unit/Digital Service Unit (CSU/DSU) for direct connection to a T1 line.
Introduction RELATED MANUALS The following manuals may help the user to set up and manage the HSIM-SSR-600: Cabletron Systems Ethernet Technology Guide Cabletron Systems Cabling Guide The applicable Cabletron Systems SWPIM manual(s) The manuals referenced above can be obtained on the World Wide Web in Adobe Acrobat Portable Document Format (PDF) at the following site: http://www.cabletron.
Introduction DOCUMENT CONVENTIONS The following conventions may be used in this document: NOTE TIP ! Note symbol. Calls the reader’s attention to any item of information that may be of special importance. Tip symbol. Conveys helpful hints concerning procedures or actions. Caution symbol. Contains information essential to avoid damage to the equipment. CAUTION Electrical Hazard Warning symbol. Warns against an action that could result in personal injury or death due to an electrical hazard.
Introduction GETTING HELP For additional support related to this device or document, contact Cabletron Systems using one of the following methods: World Wide Web http://www.cabletron.com/ Phone (603) 332-9400 Internet mail support@cabletron.com FTP ftp://ftp.cabletron.com/ anonymous your email address Login Password To send comments or suggestions concerning this document, contact the Cabletron Systems Technical Writing Department via the following email address: TechWriting@cabletron.
CHAPTER 1 NETWORK REQUIREMENTS Before installing the HSIM-SSR-600, review the requirements and specifications referred to in this chapter concerning the following: • 10BASE-T Twisted Pair Network (Section 1.2) • 100BASE-TX Twisted Pair Network (Section 1.3) The network installation must meet the guidelines in this chapter and in the documents referenced in this chapter to ensure satisfactory performance of the equipment. Failure to follow the guidelines may produce poor network performance.
Chapter 1: Network Requirements 1.2 10BASE-T NETWORK When connecting a 10BASE-T segment to the HSIM-SSR-600 port, ensure that the network meets the Ethernet network requirements of the IEEE 802.3 standard for 10BASE-T. Refer to the Cabletron Systems Cabling Guide for details. NOTE 1.3 If a port is to operate at 100 Mbps, Category 5 cabling must be used. For 10 Mbps operation only, Category 3 cabling can be used. Refer to Section 1.3 for information about 100BASE-TX networks and cabling.
CHAPTER 2 INSTALLATION To install the HSIM-SSR-600 the following items are required: • Antistatic wrist strap (shipped with the HSIM-SSR-600) • Phillips screwdriver • Cable adapter, Part Number 9360222, (shipped with the HSIM-SSR-600), needed to connect the Local Management port NOTE 2.1 Before attempting to use the HSIM-SSR-600 you should be familiar with the IEEE 802.3 Specifications, and T1 Networking.
Chapter 2: Installation 2.2 INSTALLING THE HSIM-SSR-600 Only qualified personnel should install or service this unit. An HSIM-SSR-600 can be installed in any second generation Cabletron Systems device that supports HSIM technology (e.g., 2H252-25R, 2H253-25, 6H252-17). NOTE Refer to the Release Notes for the version of firmware running on the Cabletron Systems host platform to ensure that the HSIM-SSR-600 is supported.
Installing Options 2.3.1 ! CAUTION Optional SSR-600-ECM Installation Failure to follow the procedures in the indicated documentation can lead to damage to either the installed option or the HSIM-SSR-600. Figure 2-1 details the board layout of the HSIM-SSR-600 to show where the SSR-600-ECM Auxilliary Card can be installed. To properly install an SSR-600-ECM to enhance the encryption/compression performance of the HSIM-SSR-600, refer to the instructions enclosed with the SSR-600-ECM.
Chapter 2: Installation 2.3.2 Installing Sliding WAN Physical Interface Modules The HSIM-SSR-600 can have up to two Sliding WAN Physical Interface Modules (SWPIMs) installed. Figure 2-2 indicates the ports in the HSIM-SSR-600 into which the SWPIMs can be installed. SWPIMs may be installed before or after the HSIM-SSR-600 is installed in the host platform.
Installing Options 2.3.3 Installing the HSIM-SSR-600 in an Interface Module To install an HSIM-SSR-600 in an interface module that supports HSIM technology, perform the following steps. 1. Note the ports of the interface module that have cables attached to them. Write down the ports and label the cables to make it easier to reattach the network properly after the installation. Then disconnect those cables from the ports. 2.
Chapter 2: Installation 6. Refer to Figure 2-5 and place the HSIM-SSR-600 behind the module faceplate. Standoff Screws Connector Connector Cutaway view of connector HSIM-SSR-600 Standoff SP D/ 10 0 XM T RC HSIM Pins HS IM -S 10 SR /10 60 0 0 V CP U id Standoff Faceplate Mounting Screws Interface Module or Device (Host Platform) Figure 2-5 Installing the HSIM-SSR-600 7. Align the connector on the HSIM-SSR-600 with the pins on the module.
Installing Options 8. Press down firmly on the connector area of the HSIM-SSR-600 until the connector slides all the way onto the pins. Ensure that the standoffs on the interface module align with the standoff screw holes on the HSIM-SSR-600. 9. Fasten the HSIM-SSR-600 to the module faceplate using the mounting screws saved in step 5. Do not fully tighten the screws yet. 10. Fasten the HSIM-SSR-600 to the module standoffs using the standoff screws included in the HSIM-SSR-600 shipping materials.
Chapter 2: Installation 4. Remove the standalone device chassis cover (refer to the specific standalone device documentation for instructions on removing the chassis cover). 5. Refer back to Figure 2-4 and remove the two faceplate mounting screws and the HSIM coverplate. Save the screws. 6. Refer back to Figure 2-5 and place the HSIM-SSR-600 behind the standalone device faceplate. 7. Align the HSIM connector of the HSIM-SSR-600 with the connector pins on the standalone device.
Connecting the HSIM-SSR-600 to the Network 2.4 CONNECTING THE HSIM-SSR-600 TO THE NETWORK Refer to Related Manuals in the Introduction to find the appropriate software manual to configure the host device. The WAN connection must be configured in software before the physical WAN cable connection is made to the network. Refer to the appropriate SWPIM manual for information on connecting the SWPIM to the network. Failure to use the correct cable and setup may cause problems on the network. 2.4.
Chapter 2: Installation . SPD/100 HSIM-SSR-600 10/100 XMT RCV CPU 3040_15 Figure 2-6 Connecting a Twisted Pair Ethernet Segment 3. Verify that a link exists by checking that the port RCV (Receive) LED is ON (flashing yellow, blinking green, or solid green). If the RCV LED is OFF and the XMT (Transmit) LED is not blinking yellow, perform the following steps: a. Verify that the cabling being used is Category 5 UTP with an impedance between 85 and 111 ohms.
Connecting the HSIM-SSR-600 to the Network TO SSR600 Ethernet Port NOTE: RX+/RX- and TX+/TXmust share a common color pair. TO Other Device Port RX+ 1 1 RX+ RX- 2 2 RX- TX+ 3 3 TX+ TX- 6 6 TX- RJ45 to RJ45 21591_04 Figure 2-7 Crossover Cable RJ45 Pinouts TO SSR600 Ethernet Port NOTE: RX+/RX- and TX+/TXmust share a common color pair.
Chapter 2: Installation 2.4.3 ! CAUTION Connecting SWPIMs to the WAN Do not connect any WAN cables without checking the guidelines and insuring that the software set-up in the HSIM-SSR-600 is correct. The WAN connection can be shut off by the phone company if the HSIM-SSR-600 is not set up properly. The WAN connections to the HSIM-SSR-600 are provided by the optional SWPIMs. The HSIM-SSR-600 supports certain WAN protocols depending on the SWPIM installed.
Software Configuration 2.5 SOFTWARE CONFIGURATION Refer to the applicable Cabletron Systems software manual to configure the HSIM-SSR-600. Refer to the Related Manuals list in the Introduction. Use the special cable adapter, Cabletron Systems part number 9360222, to connect the Local Management cable from the monitor to the console port on the HSIM-SSR-600. Refer to the applicable software manual for further information on management. .
Chapter 2: Installation 2-14 HSIM-SSR-600 Installation Guide
CHAPTER 3 TROUBLESHOOTING, SWITCHES, AND LED INDICATIONS This chapter is used to aid in determining hardware indications, problems, and switch settings. The Local Management/Ethernet port is also discussed. Figure 3-1 shows the front panel LEDs for the HSIM-SSR-600. Table 3-1 describes LED states. Table 3-2 describes switch positions. If you are having difficulty installing and configuring the HSIM-SSR-600, perform the following steps: • Review Chapter 2 (Installation).
Chapter 3: Troubleshooting, Switches, and LED Indications 3.1 NOTE FRONT PANEL LED INDICATIONS The terms flashing, blinking, and solid used in Table 3-1 indicate the following: Flashing indicates an LED flashing randomly, on for at least 20 ms when an event occurs. Blinking indicates an LED flashing at a steady rate (on for approximately 1/4 of a second and off for approximately 3/4 of a second). Solid indicates a steady LED light. No flashing or blinking.
Console Management/Ethernet Port 3.2 CONSOLE MANAGEMENT/ETHERNET PORT The RJ45 port on the front panel of the HSIM-SSR-600 can be used to transmit 10/100 Ethernet traffic or as a Local Management console port. A special cable adapter must be used to facilitate the connections, Cabletron Systems part number 9360222. The pinout for the special cable assembly is in Appendix A. Use the applicable Cabletron Systems software manuals for further information on the management of the HSIM-SSR-600.
Chapter 3: Troubleshooting, Switches, and LED Indications Table 3-2 Four-Position Switch Functions Switch Function Used to... 1 Force download Force the HSIM-SSR-600 to download a new image at bootup. 2 Restore defaults Return the HSIM-SSR-600 to the factory configuration. 3 Currently unused 4 Currently unused 3.3.1 Switch Function Procedure Use this procedure to implement a switch function: 1.
Switches 4 3 2 1 Figure 3-2 Switch Bank Layout HSIM-SSR-600 Installation Guide 3-5
Chapter 3: Troubleshooting, Switches, and LED Indications 3.4 TROUBLESHOOTING HSIM-SSR-600 HARDWARE Processor (CPU) LED Is OFF The CPU stays OFF for an extended amount of time, and the power (PWR) led on the host platform remains on. The CPU is in an unknown state. • Contact Cabletron Systems (refer to Getting Help in the Introduction). Processor (CPU) LED Is Blinking Red The processor has detected a fault condition, or has failed boot up diagnostics. • 3.
APPENDIX A SPECIFICATIONS This section describes the physical properties, environmental specifications, and safety and approval requirements for the HSIM-SSR-600. Cabletron Systems reserves the right to change these specifications at any time without notice. A.1 PHYSICAL PROPERTIES Dimensions: 4.78 H x 20.57 W x 28.65 D (cm) 1.88 H x 8.10 W x 11.28 D (in) Weight (Unit): 0.43 kg (0.95 lb) Nominal current draw on +5V supply from host platform: 2.1 A MTBF (Predicted): 407,202 hours A.
Appendix A: Specifications A.3 CABLE ADAPTER PINOUT Table A-1 shows the pin assignments for the special cable adapter used for the console port management connection, Cabletron Systems part number 9360222. Table A-2 Cable Adapter Pinout (Part Number 9360222) End 1 Pin A.
Regulatory Compliance A.5 REGULATORY COMPLIANCE Safety UL 1950, CSA C22.2 No. 950, 73/23/EEC, EN 60950, IEC 950 Electromagnetic Compatibility (EMC) FCC Part 15, CSA C108.
Appendix A: Specifications A-4 HSIM-SSR-600 Installation Guide
