SmartSwitch 9000 9G421-02/9G429-02 Local Management Appendix 9032332-01
Appendix 9G421-02/9G429-02 Module Specific Information Introduction This appendix contains local management information that is specific to the 9G421-02 and 9G429-02 Ethernet Modules. The 9G421-02 and 9G429-02 modules are 3-port Ethernet switching modules with: • • 2 front-panel gigabit Ethernet ports 1 Internal Network Bus (INB) backplane port Modifying Fields and User Privileges To modify fields on this module, you must have read-write or super-user privileges.
9G421-02/9G429-02 Module Specific Information Module Interface Codes The 9G421-02 and 9G429-02 modules have 7 interfaces each. Table 1 lists the identifying number, name, and description of each interface. Table 1.
9G421-02/9G429-02 Module Specific Information General Configuration Screen The General Configuration Screen (Figure 1), displays information about the selected module and allows you to set the following general parameters: • • • • • • Module Date and Time Screen Refresh and Lockout Time Host IP Address Subnet Mask Default Gateway and Interface TFTP Gateway IP Address SmartSwitch 9000 Local Management General Configuration Module Name: 9G421-02 Slot Number: 8 Firmware Revision: 01.00.
9G421-02/9G429-02 Module Specific Information General Configuration Screen Fields The following information briefly explains each General Configuration Screen field. Module Serial # Displays the serial number of the selected module. Module Board Revision Displays the version number of the selected module. FLASH Memory Displays the amount (megabytes) of flash memory in the selected module. Module Date Contains a value that the module recognizes as the current date.
9G421-02/9G429-02 Module Specific Information Screen Lockout Time Contains the maximum number of minutes that the Local Management application will display a module’s screen while pending input or action from a user. For example, if you enter 5 in this field, users will have up to five minutes to respond in some fashion to each of the specified module’s Local Management screens.
9G421-02/9G429-02 Module Specific Information Default Interface Contains the number that represents the interface that is connected to the module’s Default Gateway. In some instances, dissimilar modules have different corresponding interface numbers. For example, if you are assigning a default interface to a 9E133-36 module and you enter a 3, then the default interface is the Flexible Network Bus.
G421-02/9G429-02 Module Specific Information Port Statistics Screen The Port Statistics Screen (Figure 2), displays information and statistics about the module’s Ethernet ports. SmartSwitch 9000 Local Management Port Statistics Module Name: 9G421-02 Slot Number: 8 Firmware Revision: 01.00.00 BOOTPROM Revision: 01.01.
9G421-02/9G429-02 Module Specific Information Port Statistics Screen Fields The following information briefly explains each Port Statistics Screen field. PORT # Indicates the current port for which statistics are displayed. OCTETS Displays the number of octets transmitted and received on the port. PACKETS Displays the number of packets transmitted and received on the port. TOTAL ERRORS Displays the total number of errors on the port.
9G421-02/9G429-02 Module Specific Information MULTICASTS Displays the number of multicasts received. LINK STATUS Indicates whether there is a physical connection from this port to another device. One of the following values appears: • Link - There is a link signal present; there is a valid physical connection from this port to another device. • No Link - There is no link signal present; there is no valid physical connection from this port to another device.
9G421-02/9G429-02 Module Specific Information Displaying Statistics for Another Port To display statistics for another port: 1. Use the arrow keys to highlight the Port # field at the bottom of the screen. 2. Press the Space Bar to increment (or press the Backspace key to decrement) the port number. Exiting the Port Statistics Screen To exit the Port Statistics Screen, use the arrow keys to highlight RETURN, then press the Return key.
