SmartSwitch 9000 9F426-03 Local Management Appendix 9032058-01
Appendix 9F426-03 Module Specific Information Introduction This appendix contains local management information that is specific to the 9F426-03 FDDI Switch Module. Module Interfaces The 9F426-03 FDDI Switch Module has 8 interfaces. Table 1 lists the identifying number, name, and description of each interface. Table 1.
9F426-03 Module Specific Information Use the numbers listed in Table 1 to configure the module’s default interface (see General Configuration Screen in the SmartSwitch 9000 Module Local Management User’s Guide).
9F426-03 Module Specific Information Ring Map Configuration Screen The Ring Map Configuration Screen (Figure 1), contains configuration and connection information and displays the topology of the FDDI rings connected to the module. SmartSwitch 9000 Local Management Ring Map Configuration Module Name: 9F426-03 Slot Number: 11 Firmware Revision: 01.04.10 BOOTPROM Revision: 01.02.
9F426-03 Module Specific Information Ring Map Configuration Screen Fields The following information briefly explains each Ring Map Configuration Screen field. FDDI Address Displays the address of the module. The format of this address (either MAC or Canonical) is determined by the value you select in the Address Mode field. MAC Count Displays the number of MACs (Media Access Controllers) that are attached to the specified ring.
9F426-03 Module Specific Information The Ring Map The Ring Map shows a series of addresses in upstream/downstream order. These addresses, which represent each FDDI device attached to the ring, are arranged on the screen to simulate the circular fashion of a ring. When first displayed, the station at the upper left corner of this map is your current station. The screen displays node class, node address, and twisted and/or wrapped conditions (T for twisted, W for wrapped).
9F426-03 Module Specific Information Ring Map Node Screen The Ring Map Node Screen (Figure 2), displays specific information for a selected FDDI node on the Ring Map. SmartSwitch 9000 Local Management Ring Map Node Module Name: 9F426-03 Slot Number: 11 Firmware Revision: 01.04.10 BOOTPROM Revision: 01.02.
F426-03 Module Specific Information Ring Map Node Screen Fields The following information briefly explains each Ring Map Node Screen field. Address Displays the address of the selected node. Upstream Address Displays the address of the selected node’s nearest upstream neighbor. Node Class Displays the class (NAS, DAS, DAC, SAS, or SAC) of the selected node. For an explanation of these class codes, see page 5.
9F426-03 Module Specific Information Switch Configuration Screen The Switch Configuration Screen (Figure 3), displays parameters you can configure to make the switch operational. SmartSwitch 9000 Local Management Switch Configuration Module Name: 9F426-03 Slot Number: 9 Switch Address: Numbers of Ports: Port # 1 2 3 4 Firmware Revision: 01.04.10 BOOTPROM Revision: 01.02.
9F426-03 Module Specific Information Switch Configuration Screen Fields The following information briefly explains each Switch Configuration Screen field. Type of STA (Toggle) Allows you to set the method that bridges use to decide which bridge is the controlling (Root) bridge when two or more bridges exist in parallel (Spanning Tree Algorithm). Press the Space Bar to toggle to the desired value.
9F426-03 Module Specific Information Full Duplex Configuration Screen The Full Duplex Configuration Screen (Figure 4), allows you to specify transmit and receive settings for the module’s front panel ports. SmartSwitch 9000 Local Management Full Duplex Configuration Module Name: 9F426-03 Slot Number: 9 PORT# 1 2 3 SAVE OPERATION MODE FULL DUPLEX FULL DUPLEX FULL DUPLEX Firmware Revision: 01.04.10 BOOTPROM Revision: 01.02.
9F426-03 Module Specific Information Full Duplex Configuration Screen Fields The following information briefly explains each Full Duplex Configuration Screen field. OPERATION MODE (Toggle) Lets you determine whether the specified port will transmit and receive data separately or simultaneously. You can set this field to one of the following values: • FULL DUPLEX - The port can transmit and receive data at the same time. Therefore, the port is running at 200 Mbps.
9F426-03 Module Specific Information 12
