8H02-16 SmartSwitch 10/100 USER’S GUIDE MMAC Smart SWITCH 10/100 RKING SmartSwFitch NETWO AST VIRTUAL WITH SECURE 16 15 PWR CPU RESET 8H02-16 COM 1X 2X 3X 4X 5X 6X 7X 8X 9X 10X 11X 12X 13X 14X 1742-00
Only qualified personnel should install the 8H02-16. NOTICE Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made. The hardware, firmware, or software described in this manual is subject to change without notice.
Notice FCC NOTICE This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules.
Notice CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT IMPORTANT: Before utilizing this product, carefully read this License Agreement. This document is an agreement between you, the end user, and Cabletron Systems, Inc. (“Cabletron”) that sets forth your rights and obligations with respect to the Cabletron software program (the “Program”) contained in this package. The Program may be contained in firmware, chips or other media.
Notice UNITED STATES GOVERNMENT RESTRICTED RIGHTS The enclosed product (a) was developed solely at private expense; (b) contains “restricted computer software” submitted with restricted rights in accordance with Section 52227-19 (a) through (d) of the Commercial Computer Software - Restricted Rights Clause and its successors, and (c) in all respects is proprietary data belonging to Cabletron and/or its suppliers.
CONTENTS CHAPTER 1 INTRODUCTION 1.1 Using This Guide ......................................................................... 1-1 1.2 Structure of This Guide................................................................ 1-2 1.3 8H02-16 Overview....................................................................... 1-3 1.4 Local Management Features....................................................... 1-6 1.5 Optional Features ........................................................................
Contents CHAPTER 6 LOCAL MANAGEMENT 6.1 Overview ......................................................................................6-1 6.2 Local Management Keyboard Conventions .................................6-2 6.3 Accessing Local Management .....................................................6-3 6.4 Device Menu Screen....................................................................6-6 6.5 Device Configuration Menu Screen .............................................6-8 6.
Contents APPENDIX C C.1 C.2 C.3 C.4 OPTIONAL INSTALLATIONS AND MODE SWITCH BANK SETTINGS Required Tools ............................................................................C-1 Removing the Chassis Cover ......................................................C-2 Setting the Mode Switch..............................................................C-4 Installing Optional Fast Ethernet Interface Modules....................
Contents viii 8H02-16 User’s Guide
CHAPTER 1 INTRODUCTION Welcome to the Cabletron Systems 8H02-16 SmartSwitch 10/100 User’s Guide. This guide describes the 8H02-16 SmartSwitch and provides information concerning network requirements, installation, troubleshooting, and the use of Local Management for device local control and management. 1.1 USING THIS GUIDE Read through this guide completely to understand the 8H02-16 SmartSwitch features, capabilities, and Local Management functions. A general working knowledge of Ethernet and IEEE 802.
Chapter 1: Introduction 1.2 STRUCTURE OF THIS GUIDE This guide is organized as follows: Chapter 1, Introduction, outlines the contents of this manual and briefly describes the 8H02-16 features. Directions about how to receive additional help and a list of related manuals are also included. Chapter 2, Network Requirements, explains the network requirements to consider before installing the 8H02-16.
8H02-16 Overview 1.3 8H02-16 OVERVIEW The 8H02-16 is a standalone 16-port high-speed network switch device that supports traditional switching (bridging). Ports 15 and 16 support optional Fast Ethernet Interface Modules and can provide uplinks to 100BASE-TX or 100BASE-FX fast Ethernet networks.
Chapter 1: Introduction • Full Duplex Switched Ethernet (FDSE) support for 20 Mbps links to bandwidth intensive users/servers • Runtime IP Address Discovery that allows the 8H02-16 to send out a RARP or BootP request to determine its IP address • Manageable using Simple Network Management Protocol (SNMP) and Remote Monitoring (RMON) • Support for traditional switching services as well as for Cabletron Systems SECUREFAST Switching Virtual Network technology • Possible linking of existing stackable
8H02-16 Overview 1.3.4 Management Management of the 8H02-16 is accomplished using Local Management tools or remote SNMP management stations. Out-of-band local management is provided through the RS232 COM port on the front panel using a VT100 terminal or a VT100 terminal emulator. In-band remote management is possible through any SNMP compliant Network Management Software. 1.3.
Chapter 1: Introduction 1.4 LOCAL MANAGEMENT FEATURES Local Management provides the tools that allow management of the 8H02-16 and any of the optional Fast Ethernet Interface Modules installed as ports 15 and 16. It also allows the following tasks to be performed: • Assign an IP address and subnet mask to the 8H02-16. • Select a default gateway and default interface. • Control local and remote access. • Designate workstations to receive SNMP traps from the 8H02-16.
Document Conventions • Cabletron Systems provides Fast Ethernet Interface Modules to support uplinks to 100 Mbps Ethernet backbones or high speed connections to local servers. The Fast Ethernet Interface Modules are listed in Table 1-1. Table 1-1 Fast Ethernet Interface Modules P/N Description Application FE-100TX Uses RJ45 connector Supports Unshielded Twisted Pair (UTP) cabling. FE-100FX Uses SC connector Supports multimode fiber optic cabling. 1.
Chapter 1: Introduction 1.7 GETTING HELP If you need additional support related to this device, or if you have any questions, comments, or suggestions concerning this manual, contact Cabletron Systems Technical Support: Phone (603) 332-9400 Monday – Friday; 8 A.M. – 8 P.M. Eastern Time CompuServe GO CTRON from any ! prompt Internet mail support@ctron.com FTP Login Password ctron.com (134.141.197.
Related Manuals 1.
Chapter 1: Introduction 1-10 8H02-16 User’s Guide
CHAPTER 2 NETWORK REQUIREMENTS This chapter contains general networking guidelines. Before attempting to use the 8H02-16 or to install a Fast Ethernet Interface Module (FE-100TX or FE-100FX), review the requirements and specifications outlined in this chapter. 2.1 NETWORK REQUIREMENTS The network installation must meet the guidelines included in this chapter to ensure satisfactory performance of this equipment. Failure to follow these guidelines may produce poor network performance.
Chapter 2: Network Requirements Impedance Cabletron Systems 10BASE-T twisted pair products work on twisted pair cable with 75 to 165 ohms impedance. UTP cables typically have an impedance from 85 to 110 ohms. Shielded twisted pair cables, such as IBM Type 1 cable with an impedance of 150 ohms may also be used. Temperature Multi-pair PVC 24 AWG telephone cables typically have an attenuation of approximately 8–10 dB/100 m at 20°C (68°F).
Network Requirements Propagation Delay Propagation delay is the amount of time it takes data to travel from the sending device to the receiving device. Total propagation delay allowed for a 100BASE-TX (100 Mbps) network is 256 bit times or 2.56 microseconds (2.56 µs). If the total propagation delay between any two nodes on a 100BASE-TX network exceeds 2.56 µs, then use bridges or other devices to further segment the network.
Chapter 2: Network Requirements Propagation delay (collision delay) is the amount of time it takes data to travel from the sending device to the receiving device. Total propagation delay allowed for the entire network is 256 bit times (2.56 µs). If the total propagation delay between any two nodes on the network exceeds 2.56 µs, then use bridges or other devices to further segment the network. 2.
CHAPTER 3 INSTALLATION Only qualified personnel should install the 8H02-16. This chapter covers the following items: • Required tools • Unpacking the 8H02-16 • Installing the 8H02-16 on a shelf or into a standard rack • Connecting to the power source • Connecting to the network 3.1 REQUIRED TOOLS A Phillips screwdriver is required to install the equipment. 3.2 UNPACKING THE 8H02-16 To unpack the shipment, proceed as follows: 1. Carefully remove the 8H02-16 from the shipping box.
Chapter 3: Installation 3.3 8H02-16 OPTIONS Install the options first before proceeding to Section 3.4. NOTE If the 8H02-16 is to be installed with optional Fast Ethernet Interface Modules, refer to Appendix C for installation instructions. For more information on the two Fast Ethernet Interface Modules and the two optional memory kits, refer to Section 1.5, Optional Features. 3.4 INSTALLING THE 8H02-16 The 8H02-16 may be installed on a tabletop, shelf, or in a 19-inch rack. Refer to Section 3.4.
Installing the 8H02-16 3.4.2 Rackmount Installation To install the 8H02-16 in a 19-inch rack, Cabletron Systems includes an accessory kit containing the rackmount brackets, mounting screws, and a strain-relief bracket for cable management. WARNING Before installing the 8H02-16 into a rack, ensure that the rack supports the device(s) without compromising the stability of the rack. Otherwise, personal injury and/or equipment damage may result.
Chapter 3: Installation Attaching the Strain-Relief Bracket Attach the strain-relief bracket to the front of the 8H02-16 as follows: 1. Locate the strain-relief bracket and four 8-32 x 3/8-inch pan-head screws in the rackmount kit. Do not attempt to attach the strain-relief bracket with screws other than the 8-32 x 3/8-inch screws included with the 8H02-16. Use of longer screws may damage the unit or cause electrical shock. 2.
Installing the 8H02-16 Rack Mounting the 8H02-16 Proceed as follows to install the 8H02-16 into a 19-inch rack. 1. Remove and discard the four cover screws (two from each side) located along the front edges of each side of the 8H02-16. 2. Locate the four 6-32 x 3/8-inch flat head cover replacement screws in the rackmount kit. Use these screws to attach the rackmount brackets to the 8H02-16 as shown in Figure 3-3.
Chapter 3: Installation 3.4.3 NOTE Connecting to the Power Source The 8H02-16 has a power supply with automatic voltage sensing that allows connection to power sources ranging from 100–125 Vac or 200–250 Vac, 50/60 Hz. To connect the 8H02-16 to a power source, proceed as follows: 1. Plug the power cord into a grounded wall outlet. The POWER LED turns ON (green) and the CPU LED turns ON (green) briefly. It takes approximately one minute for the 8H02-16 to boot up. NOTE 2. Observe the LANVIEW LEDs.
Connecting to the Network 3.5.1 Connecting UTP Cables to Ports 1 Through 14 Before connecting a segment to the 8H02-16, check each end of the segment to verify wire crossover. ! CAUTION To establish a link, you must have an odd number of crossovers (preferably one) between 10BASE-T devices of the same type (i.e., from repeater to repeater or transceiver to transceiver). Connect a twisted pair segment to the 8H02-16 as follows: 1.
Chapter 3: Installation TO SmartSwitch RJ45 Port NOTE: RX+/RX– and TX+/TX– must share a common color pair. TO 10BASE-T Device Port RX+ 1 1 RX+ RX– 2 2 RX– TX+ 3 3 TX+ TX– 6 6 TX– RJ45 to RJ45 1574-30 Figure 3-6 Cable Pinouts - (RJ45) Crossover Cable c. Check that the twisted pair connection meets the dB loss and cable specifications outlined in Chapter 2. If a link is not established, contact Cabletron Systems Technical Support. Refer to Section 1.7, Getting Help, for details. 4.
Connecting to the Network Position X (crossed over) Position = (not crossed over) 1. TX+ 2. TX3. RX+ 4. NC 5. NC 6. RX7. NC 8. NC = x 10 100 FE-100TX 1. RX+ 2. RX3. TX+ 4. NC 5. NC 6. TX7. NC 8. NC 166505 Figure 3-7 FE-100TX Crossover Switch Connect an FE-100TX to a twisted pair segment as follows: 1. Ensure that the device at the other end of the segment is connected to the segment and is powered ON. 2.
Chapter 3: Installation 3. Verify that a Link exists by checking that the port RX LED is on (flashing green or yellow or on solid green). If the RX LED is off, perform the following steps until it is on: a. Check that the 100BASE-TX device at the other end of the twisted pair segment is powered up. b. Verify that the RJ45 connector on the twisted pair segment has the proper pinouts. c. Check the cable for continuity. d.
Connecting to the Network Fiber Optic Network Connection 1. Remove the protective plastic covers from the fiber optic ports on the applicable port on the module and from the ends of the connectors. ! CAUTION Do not touch the ends of the fiber optic strands, and do not let the ends come in contact with dust, dirt, or other contaminants. Contamination of the ends causes problems in data transmissions. If the ends become contaminated, clean them with alcohol using a soft, clean, lint free cloth. 2.
Chapter 3: Installation 4. Verify that a Link exists by checking that the port RX LED is flashing green or yellow, or on solid green. If the RX LED is off, perform the following steps until it is on: The port RX LED flashes green and yellow during bootup. NOTE a. Check that the power is turned on for the device at the other end of the Link. b. Verify proper crossing over of fiber strands between the applicable port on the 8H02-16 and the fiber optic device at the other end of the fiber optic link segment.
CHAPTER 4 TROUBLESHOOTING This chapter provides information concerning the following: • Using the LANVIEW diagnostic and status monitoring system • Troubleshooting network and 8H02-16 operational problems • Using the RESET button 4.1 USING LANVIEW The 8H02-16 uses Cabletron Systems built-in visual diagnostic and status monitoring system called LANVIEW. The LANVIEW LEDs (Figure 4-1) allow quick observation of the network status to aid in diagnosing of network problems.
Chapter 4: Troubleshooting Table 4-1 LANVIEW LEDs LED Color State Recommended Action PWR Green Functional. No action. Red 5-Volt output out of regulation. Contact Cabletron Systems Technical Support. CPU TX RX Off Power off. Power up device. Red Flashing. Hardware failure has occurred. Contact Cabletron Systems Technical Support. Solid. Reset, normal power up reset. No action. Yellow Crippled. Limited functionality. Contact Cabletron Systems Technical Support. Green Functional.
FE-100TX LED 4.2 FE-100TX LED The optional FE-100TX has one LED labeled 10/100. The 10/100 LED together with the receive LED allows the user to determine the Link status and the operating speed of the Fast Ethernet Interface Module. The 10/100TX LED and the Receive (RX) LED are shown in Figure 4-2. Table 4-2 and Table 4-3 provide a functional description of the FE-100TX LED.
Chapter 4: Troubleshooting No Link exists if the Receive (RX) LED is off. NOTE Table 4-3 FE-100TX LED (Without Link) LED Color Description 10/100 Off No Link or no cable attached. FE-100TX forced to 10 Mbps operation, or is manually set to “auto-negotiate” mode. Green No Link or no cable attached. FE-100TX is forced to 100 Mbps operation.
Troubleshooting Checklist 4.3 TROUBLESHOOTING CHECKLIST If the 8H02-16 is not working properly, refer to Table 4-4 for a checklist of possible problems, causes, and recommended actions to resolve the problem. Table 4-4 Troubleshooting Checklist Problem Possible Cause Recommended Action All LEDs are OFF. Loss of Power to the 8H02-16. Check the proper connection of the power cable and its access to a live outlet. 8H02-16 not properly installed. Check the installation. Autobaud not enabled.
Chapter 4: Troubleshooting 4.4 USING THE RESET BUTTON The RESET button shown in Figure 4-3 resets the 8H02-16 processor without affecting the NVRAM. The RESET button may be used in conjunction with mode switch 7, described in Appendix C, to clear user-entered parameters such as IP addresses and Community Names and to replace them with the 8H02-16 default settings.
CHAPTER 5 COM PORT AND TELNET CONNECTIONS This chapter provides information about the following items: • Connecting and configuring a management terminal to the COM port of the 8H02-16 to access Local Management • Connecting an Uninterruptible Power Supply (UPS) to the COM port of the 8H02-16 for UPS applications • Establishing a Telnet connection 5.
Chapter 5: COM Port and Telnet Connections Table 5-1 VT Terminal Setup Display Setup Menu Columns -> Controls -> Auto Wrap -> Scroll -> Text Cursor -> Cursor Style -> 80 Columns Interpret Controls No Auto Wrap Jump Scroll Cursor Underline Cursor Style General Setup Menu Mode -> ID number -> Cursor Keys -> Power Supply -> VT100, 7 Bit Controls VT100ID Normal Cursor Keys UPSS DEC Supplemental Communications Setup Menu Transmit -> Receive -> XOFF -> Bits -> Parity -> Stop Bit -> Local Echo -> Port -> Tra
Connecting a Management Terminal to the 8H02-16 5.3 CONNECTING A MANAGEMENT TERMINAL TO THE 8H02-16 The 8H02-16 comes with a Console Cable Kit that provides a cable and RJ45-to-DB9 adapter. The adapter allows the 8H02-16 RJ45 COM port to connect to an IBM or compatible PC running a VT series emulation software package. For detailed instructions regarding the connection of the console cable to the 8H02-16, refer to the instruction sheet provided in the Console Cable Kit.
Chapter 5: COM Port and Telnet Connections 5.5 RUNTIME IP ADDRESS DISCOVERY Upon power up, the 8H02-16, through a function called Runtime IP Address Discovery, sends out a RARP and BootP request over the network to determine its IP address. This function allows the loading of an IP address into NVRAM on the 8H02-16 without using Local Management. For information on setting up a workstation to act as a server to respond to a RARP or BootP request, refer to the specific workstation documentation. 5.
CHAPTER 6 LOCAL MANAGEMENT This chapter describes how to access and use Local Management for the 8H02-16. 6.1 OVERVIEW Local Management for the 8H02-16 consists of a series of management screens that allow the management of the 8H02-16 and its attached segments.
Chapter 6: Local Management 6.2 LOCAL MANAGEMENT KEYBOARD CONVENTIONS All key names appear as capital letters in this manual. Table 6-1 explains the keyboard conventions and the key functions that are used. Table 6-1 Keyboard Conventions Key Function ENTER Key RETURN Key These are selection keys that perform the same Local Management function. For example, “Press ENTER” means that you can press either ENTER or RETURN, unless this manual specifically instructs you otherwise.
Accessing Local Management 6.3 ACCESSING LOCAL MANAGEMENT Perform the following steps to access Local Management: 1. Turn on the terminal. Press ENTER (up to four times) until the 8H02-16 Local Management Password screen, Figure 6-1, appears. Event Message Line 8H02-16 LOCAL MANAGEMENT CABLETRON Systems, Incorporated P.O.Box 5005 Rochester, NH 03866-5005 USA (603) 332-9400 (c) Copyright CABLETRON Systems, Inc, 1996 Device Serial Number: XX.XX.
Chapter 6: Local Management 2. Enter the Password and press ENTER. The default Super-User access password is “public” or press ENTER. The user’s password is one of the community names specified in the SNMP Community Names screen. Access to certain Local Management capabilities depends on the degree of access accorded that community name. Refer to Section 6.7. NOTE • If an invalid password is entered, the terminal beeps and the cursor returns to the beginning of the password entry field.
Accessing Local Management 6.3.2 Selecting Local Management Menu Screen Items Select items on a menu screen by performing the following steps: 1. Use the arrow keys to highlight a menu item. 2. Press ENTER. The selected menu item appears on the screen. 6.3.3 Exiting Local Management Screens Exit a Local Management screen by performing the following steps: 1. Use the arrow keys to highlight the RETURN command at the bottom of the Local Management screen. 2. Press ENTER.
Chapter 6: Local Management 6.4 DEVICE MENU SCREEN The Device Menu screen is the access point for all Local Management screens. Figure 6-3 shows the Device Menu screen. Event Message Line 8H02-16 LOCAL MANAGEMENT Device Menu Device Name: 8H02-16 Firmware Revision: XX.XX.XX BOOTPROM Revision: XX.XX.
Device Menu Screen The following explains each Device Menu screen field as shown in Figure 6-3: DEVICE CONFIGURATION The Device Configuration screen provides access to the Local Management screens that are used to configure the 8H02-16 and also to the Device Specific Configuration Menu screen. The Device Specific Configuration Menu screen provides access to the screens that allow the user to check the 8H02-16 resources and set operating parameters specific to each port.
Chapter 6: Local Management 6.5 DEVICE CONFIGURATION MENU SCREEN The Device Configuration Menu screen, Figure 6-4, provides access to Local Management screens that allow the user to configure and monitor operating parameters, modify SNMP community names, set SNMP traps, configure bridge parameters and configure 8H02-16 ports. Event Message Line 8H02-16 LOCAL MANAGEMENT Device Configuration Menu Device Name: 8H02-16 Firmware Revision: XX.XX.XX BOOTPROM Revision: XX.XX.
Device Configuration Menu Screen The following explains each Device Configuration menu screen as shown in Figure 6-4: GENERAL CONFIGURATION The General Configuration screen allows the user to monitor and configure operating parameters for the 8H02-16. For details, refer to Section 6.6. SNMP COMMUNITY NAMES The SNMP Community Names screen allows the user to change or review the community names used as access passwords for local management operation. For details, refer to Section 6.7.
Chapter 6: Local Management 6.6 GENERAL CONFIGURATION SCREEN The General Configuration screen, Figure 6-5, allows the user to set the system date and time, IP addresses and Subnet Masks, the Default Interface and Default Gateway, the TFTP Gateway IP address, and the COM port configuration. Access the General Configuration screen from the Device Configuration Menu screen by using the arrow keys to highlight the General Configuration option and pressing ENTER.
General Configuration Screen Subnet Mask (Modifiable) Displays the subnet mask for the 8H02-16. A subnet mask “masks out” the network bits of the IP address by setting the bits in the mask to 1 when the network treats the corresponding bits in the IP address as part of the network or subnetwork address, or to 0 if the corresponding bit identifies the host. For details about how to change the Subnet Mask from its default value, refer to Section 6.6.2.
Chapter 6: Local Management Screen Lockout Time (Modifiable) Contains the maximum number of minutes that the Local Management application displays a module’s screen while awaiting input or action from a user. For example, if the number 5 is entered in this field, the user has up to five minutes to respond to each of the specified module’s Local Management screens.
General Configuration Screen 6.6.1 Setting the IP Address Set the IP address by performing the following steps: 1. Use the arrow keys to highlight the IP Address field. 2. Enter the IP address into this field using Decimal Dotted Notation (DDN) format. For example: 134.141.79.120 3. Press ENTER. If the IP address is a valid format, the cursor returns to the beginning of the IP address field. If the entry is not valid, the Event Message Line displays “INVALID IP ADDRESS OR FORMAT ENTERED”.
Chapter 6: Local Management 3. Press ENTER. If the subnet mask is valid, the cursor returns to the beginning of the Subnet Mask field. If the entry is not valid, the Event Message Line displays “INVALID SUBNET MASK OR FORMAT ENTERED”. Local Management does not alter the current value, but it does refresh the Subnet Mask field with the previous value. 4. Use the arrow keys to highlight the SAVE command. 5. Press ENTER.
General Configuration Screen 6.6.4 Setting the Default Interface The default interface is the interface channel for the designated default gateway. Set the default interface by performing the following steps: 1. Use the arrow keys to highlight the Default Interface field. 2. Enter the interface number for the default gateway in this field with a value from 1 to 16. 3. Press ENTER. If the interface number entered is a valid format, the cursor returns to the beginning of the Default Interface field.
Chapter 6: Local Management 6.6.6 Setting the Device Date To set the system date, perform the following steps: 1. Use the arrow keys to highlight the Device Date field. 2. Enter the date in a MM/DD/YY format. NOTE It is not necessary to add separators between month, day, and year numbers, as long as each entry uses two numeric characters. For example, to set the date to 03/17/96, type “031796” in the Device Date field. 3. Press ENTER to set the system calender to the date in the input field. 4.
General Configuration Screen If the time entered is a valid format, the Event Message Line at the top of the screen displays “SAVED OK”. If the entry is not valid, Local Management does not alter the current value and refreshes the Device Time field with the previous value. 6.6.8 Entering a New Screen Refresh Time The screen refresh time is set from 3 to 99 seconds with a default of 3 seconds. To set a new screen refresh rate, perform the following steps: 1.
Chapter 6: Local Management 6.6.10 Configuring the COM Port ! CAUT ION Before altering the COM port settings, ensure that a valid IP address is set for this device (Refer to Section 6.6.1, Setting the IP Address). Read this entire COM port configuration section before changing the settings of the COM port. The 8H02-16 COM port supports the following applications: NOTE Refer to the Release Notes included with the 8H02-16 to verify which COM Port applications are currently supported.
General Configuration Screen 6.6.11 Enabling the COM Port To enable the COM port, perform the following steps: 1. Use the arrow keys to highlight the Com 1 field. ! CAUT ION Do NOT disable or alter the settings of the COM port while operating the current Local Management connection through a terminal. Altering the COM port settings disconnects the Local Management terminal from the port, and ends the Local Management session.
Chapter 6: Local Management WARNING THE COM PORT HAS BEEN RECONFIGURED AND THERE IS NO IP ADDRESS SET FOR THIS DEVICE. YOU WILL NO LONGER BE ABLE TO MANAGE THIS BOARD. DO YOU STILL WISH TO RECONFIGURE THIS COM PORT? YES NO 174252 Figure 6-6 COM Port Warning Screen 3. Use the arrow keys to highlight YES. Press ENTER. 4. If you ENABLE the port, refer to Section 6.6.12. Otherwise, use the arrow keys to highlight SAVE at the bottom of the screen, then press ENTER. 5.
General Configuration Screen 6.6.12 Changing the COM Port Application After enabling the COM port as described in Section 6.6.11, select one of the four applications supported by the COM port: LM, SLIP, PPP or UPS. The default application is LM. ! CAUT ION If the COM port is reconfigured without a valid IP address set on the device, the message shown in Figure 6-6 appears. Do not continue unless the outcome of the action is fully understood. To change the COM port application: 1.
Chapter 6: Local Management 6.6.13 Setting the Baud Rate If SLIP or PPP is selected in the previous section, a separate field appears to the right of the Application field that allows the user to select the baud rate. Change the baud rate setting as follows: 1. Use the arrow keys to highlight the Baud Rate field. 2. Use the SPACE bar or BACKSPACE to step to the correct setting. 3. Press ENTER to accept the baud rate. 4. Use the arrow keys to highlight SAVE at the bottom of the screen, then press ENTER. 5.
SNMP Community Names Screen 6.7 SNMP COMMUNITY NAMES SCREEN The SNMP Community Names option allows the user to set Local Management community names. Community names act as passwords to Local/Remote Management and are agents of security access to the 8H02-16. Access to the 8H02-16 is controlled by enacting any of three different levels of security authorization (read-only, read-write, and super-user).
Chapter 6: Local Management The following explains each SNMP Community Names screen field: Community Name (Modifiable) Displays the user-defined name through which a user accesses the 8H02-16 Local Management. Any community name assigned here acts as a password to Local Management. Access Policy (Read-Only) Indicates the access status accorded each community name.
SNMP Community Names Screen 6.7.1 Establishing Community Names The password used to access Local Management at the Password Screen must have Super-User access in order for edits in the SNMP Community Names screen to take effect. Using a password with Read-Only or Read-Write access does not allow the user to edit the SNMP Community Names screen. NOTE Any community name assigned in the SNMP Community Names screen is a password to its corresponding level of access to Local Management.
Chapter 6: Local Management 6.8 SNMP TRAPS SCREEN Since the 8H02-16 is an SNMP compliant device, it sends messages to multiple Network Management Stations to alert users of status changes. The SNMP Traps screen is shown in Figure 6-8. Access the SNMP Traps screen from the Device Configuration Menu screen by using the arrow keys to highlight the SNMP Traps option and pressing ENTER. The SNMP Traps screen shown in Figure 6-8 appears.
Configuring the Trap Table Enable Traps (Toggle) Enables transmission of the traps to the network management station with the associated IP address. This field toggles between [YES] and [NO]. 6.9 CONFIGURING THE TRAP TABLE To configure the Trap table, proceed as follows: 1. Using the arrow keys, highlight the appropriate Trap Destination field. 2. Enter the IP Address of the workstation that is to receive traps. IP address entries must follow the DDN format. For example: 134.141.79.121 3. Press ENTER.
Chapter 6: Local Management 6.10 BRIDGE CONFIGURATION SCREEN The Bridge Configuration screen, Figure 6-9, provides the basic setup options to make a bridge operational in your network. Access the Bridge Configuration screen from the Device Configuration menu by using the arrow keys to highlight the Bridge Configuration option and pressing ENTER. The Bridge Configuration screen, Figure 6-9, appears.
Bridge Configuration Screen Type of STA (Toggle) Allows the user to set the method that bridges use to decide which bridge is the controlling (Root) bridge when two or more bridges exist in parallel (Spanning Tree Algorithm). Valid entries include IEEE, DEC, and None. To set the STA, refer to Section 6.10.1. Port # (Read-Only) Lists each bridge port on the device. If the number of ports is greater than eight, then the additional ports are listed on subsequent screens.
Chapter 6: Local Management 6.10.1 Selecting the STA The STA setting allows the user to set the method that the bridges use to decide which is the controller (Root) bridge when two or more bridges are in parallel (Spanning Tree Algorithm). The available selections are IEEE, DEC, and NONE. To set the STA, proceed as follows: 1. Use the arrow keys to highlight the Type of STA field. 2. Use the SPACE bar to step to the appropriate setting (IEEE, DEC, or NONE). 3.
Device Specific Configuration Menu Screen 6.11 DEVICE SPECIFIC CONFIGURATION MENU SCREEN The Device Specific Configuration Menu screen, Figure 6-10, allows the user to select one of four screens to configure ports or check system resources specific to the 8H02-16. Access the Device Specific Configuration Menu screen from the Device Configuration Menu screen by using the arrow keys to highlight the Device Specific Configuration Menu option and pressing ENTER.
Chapter 6: Local Management The following explains each field of the Device Specific Configuration Menu screen: Full Duplex Configuration The Full Duplex Configuration screen allows each port (1 to 14) to be set for either Standard Ethernet or Full Duplex operation. The screen also indicates whether or not each port is linked to another 10BASE-T device and if that port is enabled.
Full Duplex Configuration Screen Port Redirect Function This screen allows the user to redirect traffic from one or multiple ports to a specific destination port. 6.12 FULL DUPLEX CONFIGURATION SCREEN The Full Duplex Configuration screen, Figure 6-11, allows the user to set ports 1 through 14 for either Standard Ethernet or Full Duplex operation and monitor each port to see whether or not it is enabled and linked to another 10BASE-T device.
Chapter 6: Local Management This section explains each field of the Full Duplex Configuration screen. Operation Mode (Toggle) Allows the user to set the specified port to transmit and receive data separately or simultaneously. Set this field to one of the following values: • STANDARD ENET – The port is running at 10 Mbps (default) and either transmits data or receives data, but not both at the same time. To set Ethernet ports for Full Duplex operation, refer to Section 6.12.1.
Full Duplex Configuration Screen [Ports 9-14] (Read-only) When the Full Duplex Configuration screen appears, the current operation mode and status information are displayed for the first eight ports. This field allows the user to step to a second screen for the same type of information for ports 9 through 14. While on the second screen, this field changes to [Ports 1-8] so the user can navigate back to the first screen.
Chapter 6: Local Management 6.13 SYSTEM RESOURCES SCREEN The System Resources screen, Figure 6-12, provides information concerning the processor used in the 8H02-16 and the amount of FLASH memory, DRAM, and NVRAM that is installed and how much of that memory is available. Access the System Resources screen from the Device Specific Configuration Menu screen by using the arrow keys to highlight the System Resources option and pressing ENTER. The System Resources screen appears.
System Resources Screen Flash Memory Installed (Read-only) Indicates the amount of FLASH memory installed in the 8H02-16 and how much is currently available. DRAM Installed (Read-only) Indicates the amount of DRAM installed in the 8H02-16 and how much of it is currently available. NVRAM Installed (Read-only) Indicates the amount of NVRAM installed in the 8H02-16 and how much of it is currently available.
Chapter 6: Local Management 6.13.1 Resetting the Peak Switch Utilization Set the Peak Switch Utilization field to YES or NO as follows: 1. Use the arrow keys to highlight the Peak Switch Utilization field. 2. Press the SPACE bar to select YES or NO. 3. Use the arrows keys to highlight the SAVE command at the bottom of the screen. 4. Press ENTER. The message “SAVED OK” is displayed. 6.13.
High Speed Interface Configuration Screen 6.14 HIGH SPEED INTERFACE CONFIGURATION SCREEN The High Speed Interface Configuration screen, Figure 6-13, applies only to ports 15 and 16. This screen supports the FE-100TX and the FE-100FX Fast Ethernet Interface Modules that operate at 100 Mbps. The High Speed Interface Configuration screen displays the types of interfaces installed in ports 15 and 16, their current operating mode, and indicates if the ports are linked.
Chapter 6: Local Management The following briefly explains each field of the High Speed Interface Configuration screen. Port Type (Read-only) Displays the name of the interface (FE-100FX or FE-100TX) installed in ports 15 and 16. Figure 6-13 shows that there is an FE-100TX interface installed in Port 15 and no interface [N/A] in Port 16. Link Status (Read-only) Indicates whether or not there is a physical connection from this port to another 10BASE-T or 100BASE-TX/FX device.
High Speed Interface Configuration Screen NOTE In normal operation, the port with an FE-100TX installed automatically establishes a link with the device at the other end of the segment without requiring user setup. However, Local Management provides the user with the option of manually configuring that port. If an FE-100TX is installed, the field steps to Auto-Negotiation, 10Base-T, 10Base-TFD (full duplex), 100Base-TX, and 100Base-TXFD (full duplex).
Chapter 6: Local Management 6.14.2 Setting the FE-100FX Operational Mode Use this field to set the active technology. This field toggles between 100Base-FX and 100Base-FXFD (full duplex). To set the active technology through Local Management, proceed as follows: 1. Use the arrow keys to highlight the Desired Operational Mode field. 2. Use the SPACE bar to select 100Base-FX or 100Base-FXFD (full duplex). 3. Press ENTER. The port now operates in the chosen mode. 4.
High Speed Interface Configuration Screen 6.14.5 Setting the FE-100TX Advertised Ability In normal operation, a port (15 or 16) with an FE-100TX auto-negotiates to the highest speed possible. Under some circumstances, the Network Administrator may want the port to advertise only some of the available modes and not operate in other modes. This field steps between 10Base-T, 10Base-TFD (full duplex), 100Base-TX, and 100Base-TXFD (full duplex). To set the advertised ability, proceed as follows: 1.
Chapter 6: Local Management 6.15 FLASH DOWNLOAD SCREEN The Flash Download screen, shown in Figure 6-14, allows the user to clear the information stored in the 8H02-16 FLASH memory and download a new image file from a TFTP server. The user may also force a download by changing the position of Switch 6 located inside the device. Refer to Section C.3, Setting the Mode Switch, for details. Before downloading a new image to the device, load the image onto the network TFTP server.
Flash Download Screen The following briefly explains each field of the Flash Download screen: Download Method (Selectable) This field toggles between BOOTP and TFTP. If set for BootP, the device sends out a BootP request to determine the IP address of the TFTP server and the filename of the image to be downloaded. If set for TFTP, the 8H02-16 attempts a TFTP download based on the IP address and filename entered in the fields at the bottom of the Flash Download screen.
Chapter 6: Local Management 6.15.1 Image File Download Using TFTP Set the 8H02-16 to download to FLASH using TFTP as follows: 1. Use the arrow keys to highlight the Download Method field. 2. Use the SPACE bar to select TFTP. 3. Use the arrow keys to highlight the TFTP Gateway IP Addr field. 4. Set the IP address of the TFTP gateway server (this defaults to the same IP address as that set in the TFTP Gateway IP Addr field on the General Configuration screen). 5.
Flash Download Screen 6.15.2 Image File Download Using BootP Set the 8H02-16 to download to FLASH using BootP as follows: 1. Use the arrow keys to highlight the Download Method field. 2. Use the SPACE bar to select BOOTP. 3. Use the arrow keys to highlight the TFTP Gateway IP Addr field. Set the IP address of the TFTP gateway server (this defaults to the same IP address set in the TFTP Gateway IP Addr field in the General Configuration screen). 4.
Chapter 6: Local Management 6.16 ! CLEAR NVRAM SCREEN CAUT ION Clearing NVRAM will result in the loss of all user-entered parameters. Do not proceed unless this procedure is completely understood. The Clear NVRAM screen shown in Figure 6-15 allows the user to clear all user-entered parameters such as the IP address, Interface Configuration, COM Port Configuration and Community Names from NVRAM.
Clear NVRAM Screen Clear NVRAM as follows: 1. Use the arrow keys to highlight the Clear NVRAM field. 2. Use the SPACE bar to toggle the field to YES. 3. Use the arrow keys to highlight EXECUTE at the bottom of the screen. 4. Press ENTER. The warning shown in Figure 6-16 is displayed. WARNING YOU HAVE ELECTED TO CLEAR NVRAM. THIS WILL CLEAR ALL SYSTEM DEFAULTS INCLUDING BUT NOT LIMITED TO IP ADDRESS, INTERFACE CONFIGURATION, AND COM PORT CONFIGURATION, THEN RESET THE BOARD.
Chapter 6: Local Management 6.17 PORT REDIRECT FUNCTION SCREEN The Port Redirect Function screen, Figure 6-17, allows the user to set each one of the ports 1 through 16 as a source or destination port. A port can be set to have one or more destination ports. For example, port 1 can be set as a source port with three destinations, ports 2, 3, and 4. Traffic from port 1 is then automatically redirected to ports 2, 3, and 4. Port 1 can also serve as a destination port for other ports.
Port Redirect Function Screen The following definitions briefly explain each field of the Port Redirect Function screen: Source Port (Read-only) Shows which ports are currently set as source ports. Destination Port (Read-only) Shows which ports are currently set as destination ports. Source Port [n] (Selectable) Allows a selected port [n] to be changed to a source port. Destination Port [n] (Selectable) Allows a selected port [n] to be changed to a destination port.
Chapter 6: Local Management 6.17.2 Changing Source and Destination Ports Add or delete source port and destination port entries as follows: 1. Use the arrow keys to highlight the Source Port field. 2. Press the SPACE bar or BACKSPACE one or more times to increment or decrement the port number displayed in the brackets [n] until the appropriate port number is displayed. 3. Use the arrow keys to highlight the Destination Port field. 4.
Device Statistics Menu Screen 6.18 DEVICE STATISTICS MENU SCREEN The Device Statistics Menu screen, Figure 6-18, provides access to screens that allow the user to obtain bridge statistics about frame traffic through each interface and view operating statistics about each port. Access the Device Statistics Menu from the Device Menu screen by using the arrow keys to highlight the Device Statistics Menu option and pressing ENTER. The Device Statistics Menu screen appears.
Chapter 6: Local Management 6.19 BRIDGE STATISTICS SCREEN The Bridge Statistics screen, Figure 6-19, lists the number of frames received, transmitted, filtered, and forwarded by each interface. Access the Bridge Statistics screen from the Device Statistics Menu screen by using the arrow keys to highlight the Bridge Statistics option and pressing ENTER. The Bridge Statistics screen appears. Event Message Line 8H02-16 LOCAL MANAGEMENT Bridge Statistics Device Name: 8H02-16 Firmware Revision: XX.XX.
Port Statistics Screen Frames Fltrd (Read-Only) Displays the number of frames filtered by the interface. Frames Frwded (Read-Only) Displays the number of frames forwarded by the interface. 6.20 PORT STATISTICS SCREEN Operating statistics for each port, on a port-by-port basis, are viewed through the Port Statistics screen shown in Figure 6-20. Access the Port Statistics screen by using the arrow keys to highlight the Port Statistics option on the Device Statistics Menu screen and pressing ENTER.
Chapter 6: Local Management The following definitions explain each field of the Port Statistics screen: Port # (Selectable) Indicates the current port for which statistics are displayed. To select a port, refer to Section 6.20.1. Bytes (Read-only) Displays the number of bytes transmitted and received. Frames (Read-only) Displays the number of frames transmitted and received. Total Errors (Read-only) Displays the total number of errors on this port.
Port Statistics Screen Broadcasts (Read-only) Displays the number of broadcasts transmitted and received. Multicasts (Read-only) Displays the number of multicasts transmitted and received. Link Status (Read-only) Displays either Link, No Link or N/A. Port Type (Read-only) Displays either RJ45 or MMF SC (multimode fiber, SC connector for FE-100FX port). Port Status (Read-only) Indicates the status of the selected port. Possible values are ENABLED and DISABLED.
Chapter 6: Local Management 6.21 NETWORK TOOLS The Network Tools function, shown in Figure 6-21, resides on the 8H02-16 and allows the user to access and manage network devices. Access the Network Tools screen by using the arrow keys to highlight the Network Tools option on the Device Menu screen and pressing ENTER. The Network Tools screen appears.
Network Tools NOTE The conventions used here to describe Network Tools are as follows: • Information entered by the user is in helvetica font • Arguments enclosed by [ ] are required • Arguments enclosed by < > are optional • To abort or interrupt a process, press the control key and c key simultaneously, designated, or ^c here. 6.21.1 Built-in Commands The built-in commands listed in this section activate functions on the LM managed device or devices being accessed through MIB Navigation.
Chapter 6: Local Management You can specify the arp command without options, or with one of the following options: Options: -a View cache data -d Delete an IP address entry. Requires additional arguments: -s Adds a static entry. Requires additional arguments: -f Flush the ARP cache Example: NetTools-> arp -a # Interface # (SonicInt) # (SonicInt) # (SonicInt) # (SonicInt) Network Address 122.144.40.111 122.144.48.109 122.144.
Network Tools bridge: Syntax: bridge [ENABLE/DISABLE] [IFNUM/ALL] Description: The bridge command allows bridge management to be enabled or disabled at the user’s request, either one at a time or all at once. Specifying a single interface number will affect the bridging status of that interface, while specifying ALL will affect every interface.
Chapter 6: Local Management netstat: Syntax: netstat [option] Description: The netstat command provides a display of general network statistics for the managed device. The netstat command must be used with one of the two display options.
Network Tools ping: Syntax: ping [IP address] Description: The ping command generates an outbound ping request to check the status (alive/not alive) of a device at a specified IP address. Options: Not Applicable Example: NetTools-> ping 122.144.40.10 122.144.40.10 is alive 051471 reset: Syntax: reset Description: The reset command allows a soft reset of the device. The user will be queried to confirm the reset command to insure against unwanted resets.
Chapter 6: Local Management show: Syntax: show [PROTOCOL] [TABLE] Description: The show command displays information concerning various components of the device. Protocols currently supported are IP, IPX, DECnet, and AppleTalk. Components of those protocols that are currently supported are ARP caches, route tables, FIB tables, server tables, and interface tables. The number of valid entries in the table will be displayed at the end of the table display.
Network Tools traceroute: Syntax: traceroute [IP address] Description: The traceroute command generates a TRACEROUTE request to a specified IP address and provides a display of all next-hop routers in the path to the device. If the device is not reached, the command displays all next-hop routers to the point of failure. Options: Not Applicable Example: NetTools-> traceroute 122.144.11.52 # next-hop[0] : 122.144.60.45 # next-hop[1] : 122.144.8.113 # next-hop[2] : 122.144.61.45 # 122.144.11.
Chapter 6: Local Management 6.21.2 Special Commands done, quit, exit: Syntax: done Description: The done command enables the user to exit from Network Tools and return to the Main Menu screen.
APPENDIX A SPECIFICATIONS This appendix provides operating specifications for the Cabletron Systems 8H02-16. Cabletron Systems reserves the right to change these specifications at any time without notice. A.1 DEVICE SPECIFICATIONS Processor: Dynamic Random Access Memory (DRAM): FLASH Memory: A.2 4 MB upgradable to 8 MB 2 MB PHYSICAL PROPERTIES Dimensions: 7.1H x 43.2W x 34.3D (cm) 2.8H x 17W x 13.5D (in) 4.1 kg (9 lb) 200,000 hours Weight (Unit): MTBF (Predicted): A.
Appendix A: Specifications A.5 INPUT/OUTPUT PORTS Ports 1 through 14 Ethernet (10BASE-T compliant) with RJ45 type connectors. Slots accept two types of optional Fast Ethernet Interface Modules: the FE100-TX and the FE100-FX. Slots for optional ports 15 and 16 A.6 COM PORT/PIN ASSIGNMENTS COM port Serial communications port that supports Local Management or connection to a UPS. Also supports SLIP and PPP for the 8H02-16 management purposes.
Agency Approvals A.7 AGENCY APPROVALS Safety The 8H02-16 meets the safety requirements of UL 1950, CSA C22.2 No. 950, EN 60950 and IEC 950. Immunity The 8H02-16 meets the immunity requirements of EN 50082-1 including: IEC 801-2 (ESD), IEC 801-3 (Radiated Susceptibility), and IEC 801-4 (EFT/B). Emission The 8H02-16 meets the emission requirements of FCC Part 15 Class A, EN 55022 Class A and VCCI Class 1.
Appendix A: Specifications A-4 8H02-16 User’s Guide
APPENDIX B FE-100TX AND FE-100FX SPECIFICATIONS The 8H02-16 supports two Fast Ethernet Interface Modules: • FE-100TX • FE-100FX This appendix provides the specifications for these modules. B.1 FE-100TX The FE-100TX uses an RJ45 connector supporting Unshielded Twisted Pair (UTP) cabling. The slide switch on the FE-100TX determines the crossover status of the cable pairs. If the switch is on the X side, the pairs are internally crossed over.
Appendix B: FE-100TX and FE-100FX Specifications B.2 FE-100FX The FE-100FX shown in Figure B-2 uses an SC style connector that supports multimode fiber optic cabling. Specifications for the FE-100FX are listed below. FX FE-100 16 15 174240 Figure B-2 Table B-1 Cable Type FE-100FX Transmitter Power Worst Case Budget Typical Budget 50/125 µm fiber 6.0 dB 9.0 dB 62.5/125 µm fiber 9.0 dB 12.0 dB 100/140 µm fiber 15.0 dB 18.
APPENDIX C OPTIONAL INSTALLATIONS AND MODE SWITCH BANK SETTINGS ONLY QUALIFIED SERVICE PERSONNEL SHOULD ATTEMPT THE FOLLOWING PROCEDURES. NUR QUALIFIEZIERTE SERVICE PERSONNAL DIE FOLGENDE PROCEDURE FOLGEN SOLLTEN. SOLAMENTE PERSONAL CALIFICADO DEBE INTENTAR ESTE PROCEDIMIENTO. The top cover must be removed to gain access to the mode bank switches and to install the Fast Ethernet Interface Modules. This appendix covers the following items: • Required tools (Section C.
Appendix C: Optional Installations and Mode Switch Bank Settings C.2 REMOVING THE CHASSIS COVER This section describes how to remove the 8H02-16 chassis cover. DO NOT REMOVE THE COVER FROM THE 8H02-16 WHILE POWER IS APPLIED TO THE UNIT. HAZARDOUS VOLTAGES ARE PRESENT AND COULD CAUSE PERSONAL INJURY AND/OR DAMAGE THE UNIT. DO NOT POWER UP THE 8H02-16 AGAIN UNTIL THE COVER AND SCREWS ARE IN PLACE. DECKEL VON DAS 8H02-16 NICHT ABZIEHEN UNTER SPANNUNG.
Removing the Chassis Cover TIP Before performing step b, mark the cables connected to the 8H02-16 according to their associated port numbers. This is recommended for ease of reinstallation. b. Disconnect all network cables attached to the 8H02-16. 2. If the 8H02-16 is rack mounted, remove it from the rack and remove the rackmount brackets (refer to Chapter 3, Installation). 3. Use a Phillips screwdriver to remove the screws attaching the cover to the 8H02-16 chassis. (See Figure C-1.) 4.
Appendix C: Optional Installations and Mode Switch Bank Settings C.3 SETTING THE MODE SWITCH These switches are set at the factory and do not need to be changed unless you intend to perform the following: • Force download a new image file from a BootP server. • Clear the NVRAM and restore all user-entered parameters such as the IP address and Community Names to the 8H02-16 “Default” configuration settings. • Clear user-entered passwords stored in NVRAM and restore the default passwords.
Setting the Mode Switch • Switch 6 - Forced Download. Changing the position of this switch (i.e., moving the switch from one position to the other) clears download information from NVRAM and forces the 8H02-16 to download a new image file from a BootP server. NOTE After changing the position of switch 6, DO NOT reapply power to the 8H02-16 until there is a station acting as a BootP server, which contains the image file.
Appendix C: Optional Installations and Mode Switch Bank Settings C.4 INSTALLING OPTIONAL FAST ETHERNET INTERFACE MODULES Figure C-3 shows the location of the Fast Ethernet Interface Module connectors on the 8H02-16 board for port slots 15 and 16.
Installing Optional Fast Ethernet Interface Modules When installing Fast Ethernet Interface Modules in both port slots 15 and 16, remove the coverplates from both slot openings. In the following instructions, the optional module is shown being installed in port slot 16. TIP To remove a coverplate, refer to Figure C-4 and proceed as follows: a. Remove the two screws fastening the coverplate to the standoffs. Save the screws. b. Lift and remove the coverplate from the top of the front standoffs.
Appendix C: Optional Installations and Mode Switch Bank Settings 4. See Figure C-5. Gently pull the faceplate of the 8H02-16 forward to allow room for the Fast Ethernet Interface Modules to be aligned over the connector. 5. Carefully lower the Fast Ethernet Interface Module onto the standoffs while inserting the module connector into the associated motherboard connector.
INDEX Numerics C 100BASE-FX cable length 2-4 cable loss 2-3 fiber optic budget 2-3 propagation delay 2-3 100BASE-TX cable length 2-2 propagation delay 2-3 temperature 2-3 10BASE-T connection 3-7 impedance 2-2 length 2-1 requirements 2-1 temperature 2-2 Cable specifications 100BASE-TX UTP 2-2 10BASE-T UTP 2-1 multimode fiber optic 2-3 COM port 6-18 pin assignments A-2 Command Set 6-58 Configuration terminal 5-1 Connecting to the network 3-6 CPU management reservation 6-37, 6-38 Crossover switch B-1 Curren
Index F I FE-100FX transmitter power B-2 Fiber connection SC to SC 3-11 Full Duplex Configuration screen 6-33 full duplex 6-34 link status 6-34 operation mode 6-34, 6-35 port status 6-34 standard enet 6-34 Installation Fast Ethernet Interface Module C-6 IP address 6-10, 6-13 K Keyboard conventions 6-2 L LANVIEW LEDs 4-1 Local Management features 1-6 Password screen 6-3 G General Configuration screen 6-10 application 6-12 baud rate 6-12, 6-22 COM port 6-18 to 6-21 default gateway 6-11, 6-14 default in
Index P Password screen 6-3 Passwords 6-23 Peak switch utilization 6-37 Physical properties A-1 Port Redirect Function screen destination port 6-51 source port 6-51 status 6-51 Port Statistics screen admin status 6-57 application 6-57 broadcasts 6-57 bytes 6-56 collisions 6-56 CRC/alignment errors 6-56 fragments 6-56 frames 6-56 jabbers 6-56 link status 6-57 multicasts 6-57 operation mode 6-57 oversize packets 6-56 port # 6-56 port type 6-57 total errors 6-56 undersize packets 6-56 R RESET button 4-6 Runt
Index T Terminal configuration 5-1 Trap table configuration 6-27 Traps enable 6-27 Troubleshooting 4-1 checklist 4-5 U Unpacking 3-1 V VT setup 5-1 Index-4 8H02-16 User’s Guide
POWER SUPPLY CORD The mains cord used with this equipment must be a 2 conductor plus ground type with minimum 0.75 mm square conductors and must incorporate a standard IEC appliance coupler on one end and a mains plug on the other end which is suitable for the use and application of the product and that is approved for use in the country of application. GERMAN: Die Netzleitung, die mit diesem Geraet benuetzt wird, soll einen zwei Leiter mit Erdleiter haben, wobei die Leiter mindestens 0.
