User`s guide

ManualsBrandsCabletron Systems ManualsComputer equipment6E123-50

9032269-04

6E123-50 and 6E133-49 MicroLAN

SmartSwitch 6000 Interface Modules

User’s Guide

COM

CPU

6E123-50

Ethernet

Link

E1 E3

E2 E4

COM

CPU

6E133-49

Ethernet

Link

E1 E3

E2 E4

Summary of content (190 pages)

PAGE 1
6E123-50 and 6E133-49 MicroLAN SmartSwitch 6000 Interface Modules User’s Guide Ethernet Ethernet 6E123-50 6E133-49 E1 E3 E1 E3 COM E2 COM E4 CPU Link 1 1 3 12 12 Link 1 Link 1 E N E T E N E T 2 4 12 9032269-04 Link 1 E N E T 6 E4 CPU E N E T 5 E2 12 Link 1 Link 1 E N E T E N E T 1 2 12 12 Link 1 Link 1 E N E T E N E T 3 4 12 12
PAGE 2
PAGE 3
NOTICE Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made. The hardware, firmware, or software described in this manual is subject to change without notice.
PAGE 4
Notice INDUSTRY CANADA NOTICE This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.
PAGE 5
Notice CABLETRON SOFTWARE PROGRAM LICENSE 1. LICENSE. You have the right to use only the one (1) copy of the Program provided in this package subject to the terms and conditions of this License Agreement. You may not copy, reproduce or transmit any part of the Program except as permitted by the Copyright Act of the United States or as authorized in writing by Cabletron. 2. OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the Program. 3. APPLICABLE LAW.
PAGE 6
Notice DECLARATION OF CONFORMITY Application of Council Directive(s): Manufacturer’s Name: Manufacturer’s Address: European Representative Name: European Representative Address: Conformance to Directive(s)/Product Standards: Equipment Type/Environment: 89/336/EEC 73/23/EEC Cabletron Systems, Inc. 35 Industrial Way PO Box 5005 Rochester, NH 03867 Mr. J.
PAGE 7
CONTENTS CHAPTER 1 INTRODUCTION 1.1 Using This Guide ......................................................................... 1-1 1.2 Structure of This Guide................................................................ 1-1 1.3 6E123-50 and 6E133-49 Overview ............................................. 1-2 1.3.1 Connectivity .................................................................... 1-4 1.3.2 Full Duplex Switched Ethernet........................................ 1-4 1.3.3 Management ...........
PAGE 8
Contents 3.5 3.6 Connecting to the Network...........................................................3-5 3.5.1 Connecting UTP Cables to the 6E123-50 and 6E133-49 .................................................3-6 3.5.2 Connecting a Twisted Pair Segment to the FE-100TX ..............................................................3-8 3.5.3 Connecting a Fiber Optic Segment to the FE-100FX and FE-100F3 ..............................................3-10 Completing the Installation...........................
PAGE 9
Contents 5.11 Port Redirect Function Screen .................................................. 5-29 5.11.1 Displaying the Source and Destination Entries............. 5-31 5.11.2 Changing Source and Destination Ports....................... 5-31 5.12 Module Selection Screen........................................................... 5-33 5.12.1 Selecting a Module ....................................................... 5-34 5.13 Module Menu Screen ................................................................
PAGE 10
Contents 5.22 Flash Download Screen .............................................................5-75 5.22.1 Image File Download Using TFTP ................................5-78 5.22.2 Image File Download Using RUNTIME .........................5-79 5.22.3 Image File Download Using BootP................................5-80 5.23 Port Redirect Function Screen ...................................................5-80 5.23.1 Changing Source and Destination Ports .......................5-82 5.
PAGE 11
Contents APPENDIX B B.1 B.2 B.3 FE-100TX, FE-100FX AND FE-100F3 SPECIFICATIONS FE-100TX ....................................................................................B-1 FE-100FX ....................................................................................B-2 FE-100F3.....................................................................................B-3 APPENDIX C C.1 C.2 C.3 OPTIONAL INSTALLATIONS AND MODE SWITCH BANK SETTINGS Required Tools ................................................
PAGE 12
Contents x 6E123-50 and 6E133-49 User’s Guide
PAGE 13
CHAPTER 1 INTRODUCTION Welcome to the Cabletron Systems 6E123-50 and 6E133-49 MicroLAN SmartSwitch 6000 Interface Modules User’s Guide. This guide describes the 6E123-50 and 6E133-49 interface modules and provides information concerning network requirements, installation, troubleshooting, and the use of Local Management. 1.1 USING THIS GUIDE Read through this guide completely to understand the interface module features, capabilities, and Local Management functions.
PAGE 14
Chapter 1: Introduction Chapter 5, Local Management, describes how to access Local Management and use the Local Management screens to manage the 6E123-50, 6E133-49 modules and 6C105 chassis. Appendix A, Specifications, contains information on functionality and operating specifications, connector pinouts, environmental requirements, and physical properties.
PAGE 15
6E123-50 and 6E133-49 Overview Ethernet Ethernet 6E123-50 6E133-49 E1 E3 E1 E3 COM Ports COM E2 COM E4 CPU E2 E4 CPU Link 1 Link 1 E N E T E N E T 1 3 Link 1 Link 1 E N E T E N E T 1 3 Ethernet Networks 1- 4 12 12 Link 1 Link 1 E N E T E N E T 2 4 12 12 12 12 Link 1 Link 1 E N E T E N E T 2 4 12 12 HSIM Slot 5 Fast Ethernet Interface Module Slots (Ports 5 and 6) 6 Figure 1-1 The 6E123-50 and 6E133-49 6E123-50 and 6E133-49 User’s Guide 1-3
PAGE 16
Chapter 1: Introduction 1.3.1 Connectivity The 6E123-50 and 6E133-49 connect to Ethernet networks or workstations through 4 RJ21 ports on the front panel. These ports support 25-pair cable at lengths up to 100 meters. The ports are IEEE 802.3 10BASE-T compliant. The 6E123-50 has two front panel slots (ports 5 and 6) for optional Fast Ethernet Interface Modules to support an uplink to 100 Mbps Fast Ethernet backbones or a high speed connection to a local server.
PAGE 17
6E123-50 and 6E133-49 Overview 1.3.4 Switching Options The 6E123-50 and 6E133-49 provide 802.1D switching, 802.1Q switching, or SecureFast Switching Virtual Network Services between all of the front panel interfaces including Fast Ethernet Interface Modules and High Speed Interface Modules (HSIMs). SecureFast switching and 802.1Q switching allow for future migration to Virtual Network technologies without requiring the replacement of existing equipment. 1.3.
PAGE 18
Chapter 1: Introduction 1.3.8 Runtime IP Address Discovery This feature enables the modules to automatically accept an IP address from a BootP server on the network into NVRAM without requiring a user to enter an IP address through Local Management. When the modules are connected to the network and powered up, Runtime IP Address Discovery (RAD) checks the modules for an IP address. If one has not yet been assigned (module and 6C105 chassis IP address set to 0.0.0.
PAGE 19
Local Management Features 1.4.2 Broadcast Suppression Broadcast Suppression allows a user to set a desired limit of receive broadcast frames per port/per second to be forwarded out the other ports on the module up to the set limit. Any broadcast frames above this specified limit are dropped. In the event that broadcast frames are being suppressed, multicast and unicast frames continue to be switched. 1.4.
PAGE 20
Chapter 1: Introduction 1.4.5 Additional Local Management Functions Local Management also allows the following tasks to be performed: • Manage any module installed in the 6C105 via a single terminal connection. • Assign an IP address and subnet mask to the 6E123-50, 6E133-49 modules and 6C105 chassis. • Select a default gateway. • Control local and remote access. • Designate workstations to receive SNMP traps from the 6E133-49, 6E123-50, and 6C105 chassis.
PAGE 21
Optional Features 1.5 OPTIONAL FEATURES Options for the 6E123-50 and 6E133-49 are Fast Ethernet Interface Modules and High Speed Interface Modules to add remote uplink capability. Cabletron Systems offers Fast Ethernet Interface Modules for the 6E123-50 to support uplinks to 100 Mbps Fast Ethernet backbones or high speed connections to local servers. The Fast Ethernet Interface Modules are listed in Table 1-1.
PAGE 22
Chapter 1: Introduction 1.6 DOCUMENT CONVENTIONS The following conventions are used throughout this document: NOTE TIP ! Note symbol. Calls the reader’s attention to any item of information that may be of special importance. Tip symbol. Conveys helpful hints concerning procedures or actions. Caution symbol. Contains information essential to avoid damage to the equipment. CAUTION Electrical Hazard Warning symbol.
PAGE 23
Getting Help 1.7 GETTING HELP For additional support related to this device or document, contact the Cabletron Systems Global Call Center: World Wide Web http://www.cabletron.com/ For technical support, select Service and Support Phone (603) 332-9400 Internet mail support@cabletron.com FTP ftp://ftp.cabletron.
PAGE 24
Chapter 1: Introduction 1.
PAGE 25
CHAPTER 2 NETWORK REQUIREMENTS Before installing the 6E123-50 and 6E133-49 or Fast Ethernet Interface Modules (FE-100TX, FE-100FX, or FE-100F3), review the requirements and specifications referred to in this chapter concerning the following: • SmartTrunk (Section 2.1) • 10BASE-T Twisted Pair Network (Section 2.2) • 100BASE-TX Twisted Pair Network (Section 2.3) • 100BASE-FX Fiber Optic Network (Section 2.
PAGE 26
Chapter 2: Network Requirements 2.2 10BASE-T NETWORK When connecting a 10BASE-T segment to any of the 6E123-50 and 6E133-49 ports (ENET 1 through 4), ensure that the network meets the Ethernet network requirements of the IEEE 802.3 standard for 10BASE-T. Refer to the Cabletron Systems Cabling Guide for details. 2.3 100BASE-TX NETWORK The 6E123-50, with an FE-100TX installed in ports 5 or 6, provides an RJ45 connection that supports UTP cabling.
PAGE 27
CHAPTER 3 INSTALLATION Only qualified personnel should install the 6E123-50 and 6E133-49. This chapter covers the following items: • Required tools (Section 3.1) • Unpacking the 6E123-50 and 6E133-49 (Section 3.2) • Installing the 6E123-50 and 6E133-49 in the 6C105 chassis (Section 3.4) • Connecting to the network (Section 3.5) 3.1 REQUIRED TOOLS A Phillips screwdriver is required to install the Fast Ethernet Interface Modules in the 6E123-50. 3.2 UNPACKING THE 6E123-50 AND 6E133-49 1.
PAGE 28
Chapter 3: Installation 3.3 INSTALLING OPTIONS NOTE Install any optional equipment before proceeding to Section 3.4. If the 6E123-50 will be installed with an optional Fast Ethernet Interface Module refer to Appendix C for installation instructions. The installation instructions for the HSIMs available for the 6E133-49 are located in the associated user’s guide. 3.
PAGE 29
Installing the 6E123-50 and 6E133-49 into the 6C105 Chassis 4. Remove the module from the plastic bag. (Save the bag in the event the module must be reshipped.) Observe all precautions to prevent damage from Electrostatic Discharge (ESD). 5. Examine the module for damage. If any damage exists, DO NOT install the module. Immediately contact the Cabletron Systems Global Call Center.
PAGE 30
Chapter 3: Installation Slot Number Plastic Locking Tab 1 2 3 4 5 PS1 PS2 Ethernet 6E133-49 E1 E3 COM E2 E4 CPU Link 1 E N E T Link 1 E N E T 1 2 12 12 Link 1 E N E T Link 1 E N E T 3 4 12 Metal Back-Panel Circuit Card Card Guides Figure 3-1 3-4 12 Plastic Locking Tab 2269_02 Installing an Interface Module 6E123-50 and 6E133-49 User’s Guide
PAGE 31
Connecting to the Network 3.5 CONNECTING TO THE NETWORK This section provides the procedures for connecting UTP and fiber optic segments from the network or other devices to the modules. Ethernet segments 1 through 4 on the 6E123-50 and 6E133-49 have four RJ21 connectors for UTP connections. Ports 5 and 6 of the 6E123-50 support FE-100TX, FE-100FX, or FE-100F3 Fast Ethernet Interface Modules. The FE-100TX has an RJ45 connector for a Twisted Pair cable connection.
PAGE 32
Chapter 3: Installation 3.5.1 Connecting UTP Cables to the 6E123-50 and 6E133-49 When facing the front panel of the 6E123-50 and 6E133-49, the four RJ21 connectors represent Ethernet MicroLAN networks 1 through 4 that contain 12 ports each. All the RJ21 connectors have internal crossovers. Connect a twisted pair segment to the 6E123-50 and 6E133-49 as follows: 1. Ensure that the device connected to the other end of the segment is powered ON. 2.
PAGE 33
Connecting to the Network T T 1 3 Screw Hole Screw 12 12 Link 1 Link 1 Clip E N E T E N E T 2 4 12 Link Status LEDs 12 Clip Screw Figure 3-3 Screw Hole Connection Using the RJ21 Angle Adapter 3. Tighten the two screws on the RJ21 connector or RJ21 angle adapter, as applicable, to secure it to the module. NOTE The cable pinouts for a 25-pair cable (RJ21) can be found in the Cabletron Systems Cabling Guide. Refer to Section 1.8, for details on how to obtain this document. 4.
PAGE 34
Chapter 3: Installation 5. Verify that a link exists by checking that the port Link LEDs are on (solid green). If the Link LEDs are off, perform the following steps until they are on: a. Verify that the 10BASE-T device at the other end of the twisted pair segment is ON and connected to the segment. b. Verify that the RJ21 connectors on the twisted pair segment have the proper pinouts and check the cable for continuity. c.
PAGE 35
Connecting to the Network Connect an FE-100TX to a twisted pair segment as follows: 1. Ensure that the device connected to the other end of the segment is powered ON. 2. Connect the twisted pair segment to the module by inserting the RJ45 connector on the twisted pair segment into the RJ45 port on the module shown in Figure 3-4. 3. Verify that a link exists by checking that the port RX LED is on (flashing amber, blinking green, or solid green).
PAGE 36
Chapter 3: Installation 3.5.3 Connecting a Fiber Optic Segment to the FE-100FX and FE-100F3 The FE-100FX and FE-100F3 have an SC style network port (see Figure 3-5). Cabletron Systems supplies fiber optic cable that uses SC style connectors that are keyed to ensure proper crossing over of the transmit and receive fibers.
PAGE 37
Connecting to the Network 2. Insert one end of the SC connector into the FE-100FX or FE-100F3 installed in the 6E123-50. See Figure 3-5. 3. At the other end of the fiber optic cable, attach the SC connector to the other device. X FE-100F 6 16 5 RX LED Figure 3-5 TX LED FE-100FX and FE-100F3 Port 4. Verify that a link exists by checking that the port RX LED is on (flashing amber, blinking green, or solid green).
PAGE 38
Chapter 3: Installation 3.6 COMPLETING THE INSTALLATION After installing the 6E123-50 and 6E133-49 and any optional Fast Ethernet Interface Modules or HSIM as appropriate, the modules are now ready to be set up through Local Management. Refer to Chapter 5 to configure the modules and 6C105 chassis.
PAGE 39
CHAPTER 4 TROUBLESHOOTING This chapter provides information concerning the following: • Using the LANVIEW diagnostic and status monitoring system • Troubleshooting network and module operational problems • Using the RESET button 4.1 USING LANVIEW The 6E123-50 and 6E133-49 use Cabletron Systems built-in visual diagnostic and status monitoring system called LANVIEW. The LANVIEW LEDs (Figure 4-1) allow quick observation of the network status to aid in the diagnosing of network problems.
PAGE 40
Chapter 4: Troubleshooting Receive (RX) Ethernet Transmit (TX) 6E133-49 E1 E3 COM CPU LED E2 E4 Ethernet Status LEDs CPU Link 1 Link 1 E N E T E N E T 1 3 12 12 Link 1 Link 1 Port Link Status LEDs Port Link Status LEDs E N E T E N E T 2 4 12 12 2269_04 Figure 4-1 4-2 LANVIEW LEDs 6E123-50 and 6E133-49 User’s Guide
PAGE 41
Using LANVIEW Table 4-1 LED Color State Recommended Action Off Power off. Power up chassis. Blinking. Hardware failure has occurred. Contact the Cabletron Systems Global Call Center. Red CPU Ethernet Status (RX) of ENET1–4 and ports 5 and 6 of the 6E123-50 Ethernet Status (TX) of ENET1–4 and ports 5 and 6 of the 6E123-50 Amber Solid. Resetting, No action. normal power up reset. Blinking. Crippled. Contact the Cabletron Systems Global Call Center. Solid. Testing. No action. Green Solid.
PAGE 42
Chapter 4: Troubleshooting 4.2 FE-100TX LED The optional FE-100TX has one LED labeled 10/100. The 10/100 LED together with the Receive LED allows the user to determine the Link status and the operating speed of the Fast Ethernet Interface Module. The 10/100 LED and the Receive (RX) LED are shown in Figure 4-2. Table 4-2 and Table 4-3 provide a functional description of the FE-100TX LED when the RX LED is on or off, respectively.
PAGE 43
FE-100TX LED No link exists if the associated port (port 5 or 6) Receive (RX) LED is off. NOTE Table 4-3 LED FE-100TX LED Indications When the RX LED Is Off Color Description Off No link or no cable attached. FE-100TX forced to 10 Mbps operation, or is manually set to “auto-negotiate” mode. Green No link or no cable attached. FE-100TX is forced to 100 Mbps operation.
PAGE 44
Chapter 4: Troubleshooting 4.3 TROUBLESHOOTING CHECKLIST If the 6E123-50 and 6E133-49 is not working properly, refer to Table 4-4 for a checklist of possible problems, causes, and recommended actions to resolve the problem. Table 4-4 Problem All LEDs are OFF. No Local Management Password screen. Cannot contact the 6E123-50 and 6E133-49 from in-band management. Troubleshooting Checklist Possible Cause Recommended Action Loss of Power to the 6C105 chassis.
PAGE 45
Using the RESET Button 4.4 USING THE RESET BUTTON The RESET button, located near the upper plastic locking tab of the module, (refer to Figure 4-3) resets the 6E123-50 and 6E133-49 processor without affecting the NVRAM. ! CAUTION Pressing the RESET button resets the device, and all current switching being performed by the module is halted. A module downtime of up to two minutes will result from this action.
PAGE 46
Chapter 4: Troubleshooting 4-8 6E123-50 and 6E133-49 User’s Guide
PAGE 47
CHAPTER 5 LOCAL MANAGEMENT This chapter explains how to set up a management terminal to access 6E123-50 and 6E133-49 Local Management. It also explains how to use the Local Management screens and commands. NOTE 5.1 The Local Management screens shown in this chapter are for the 6E123-50. The 6E133-49 shares most of the following Local Management screens. All Local Management functions specific to any of the interface modules are preceded by a Note to alert the reader.
PAGE 48
Chapter 5: Local Management There are three ways to access Local Management: • Locally using a VT type terminal connected to the COM port of the 6E133-49 or 6E123-50. • Remotely using a VT type terminal connected through a modem. • In-band through a Telnet connection. 5.2 LOCAL MANAGEMENT KEYBOARD CONVENTIONS All key names appear as capital letters in this manual. Table 5-1 explains the keyboard conventions and the key functions that are used.
PAGE 49
Management Terminal Setup 5.3 MANAGEMENT TERMINAL SETUP Use one of the following systems to access Local Management: • An IBM or compatible PC running a VT series emulation software package • A Digital Equipment Corporation VT100 type terminal • A VT type terminal running emulation programs for the Digital Equipment Corporation VT100 series • A remote VT100 type terminal via a modem connection • In-band via a Telnet connection 5.3.
PAGE 50
Chapter 5: Local Management 5.3.2 Connecting an Uninterruptible Power Supply If the 6C105 chassis is connected to an American Power Conversion (APC) Uninterruptible Power Supply (UPS) for protection from a loss of power, a connection from the COM port of a module to the UPS can be made to monitor the status of the UPS. To use the COM port for this purpose, it must be reconfigured to support the UPS application. This procedure is performed from the General Configuration screen of the interface module.
PAGE 51
Management Terminal Setup 5.3.3 Management Terminal Setup Parameters Table 5-2 lists the setup parameters for the local management terminal.
PAGE 52
Chapter 5: Local Management 5.3.4 Telnet Connections Once the module or chassis has a valid IP address, the user can establish a Telnet session with Local Management from any TCP/IP based node on the network. Telnet connections to the 6E123-50 and 6E133-49 require the community name passwords assigned at the SNMP Community Names screen of either the 6C105 chassis, or the module. For additional information about community names, refer to Section 5.8, SNMP Community Names Screen.
PAGE 53
Accessing Local Management 5.4 ACCESSING LOCAL MANAGEMENT Access to Local Management is controlled through the Password screen, Figure 5-3. Whenever a connection is made to the 6E123-50 and 6E133-49 the Password screen displays. Before continuing, the user must enter a password which is compared to the previously stored passwords. The level of access allowed the user depends on the password. To set or change passwords refer to Section 5.8.
PAGE 54
Chapter 5: Local Management NOTE The User’s password is one of the community names specified in the SNMP Community Names screen. Access to certain Local Management capabilities depends on the degree of access accorded that community name. Refer to Section 5.8. • If an invalid password is entered, the terminal beeps and the cursor returns to the beginning of the password entry field.
PAGE 55
Accessing Local Management \ Chassis Menu General Configuration SNMP Community Names SNMP Traps Chassis Environmental Port Redirect Function Password Module Configuration Menu Main Menu General Configuration SNMP Community Names SNMP Traps Switch Configuration SmartTrunk Configuration Module Specific Configuration Menu Module Menu Module Statistics Menu Switch Statistics Interface Statistics RMON Statistics Repeater Statistics Network Tools Figure 5-4 Chassis Menu System Resources Fast High Speed
PAGE 56
Chapter 5: Local Management Chassis Menu General Configuration SNMP Community Names SNMP Traps Chassis Environmental Password Module Configuration Menu Main Menu General Configuration SNMP Community Names SNMP Traps Module Specific Configuration Menu Module Menu Module Statistics Menu Interface Statistics RMON Statistics Repeater Statistics Network Tools Figure 5-6 5.4.
PAGE 57
Accessing Local Management Using the RETURN Command 1. Use the arrow keys to highlight the RETURN command at the bottom of the Local Management screen. 2. Press ENTER. The previous screen in the Local Management hierarchy displays. NOTE The user can also exit Local Management screens by pressing ESC twice. This exit method does not warn about unsaved changes and all unsaved changes will be lost. 3.
PAGE 58
Chapter 5: Local Management 5.5 THE MAIN MENU SCREEN The Main Menu screen is the access point for all Local Management screens for the module and the 6C105 chassis. Figure 5-7 shows the Main Menu screen.
PAGE 59
Chassis Menu Screen MODULES The MODULES menu item provides access to the Module Selection screen that is used to select individual modules in the chassis for management purposes. Access the Module Selection screen by using the arrow keys to highlight the MODULES menu item and pressing ENTER. The Module Selection screen displays. Proceed to Section 5.12. 5.
PAGE 60
Chapter 5: Local Management The following briefly explains each screen accessible from the Chassis Menu screen. CHASSIS CONFIGURATION The Chassis Configuration screen allows the user to configure operating parameters for the 6C105 chassis. For details, refer to Section 5.7. SNMP COMMUNITY NAMES The SNMP Community Names screen allows the user to enter new, change, or review the community names used as access passwords for device management operation.
PAGE 61
Chassis Configuration Screen 5.7 CHASSIS CONFIGURATION SCREEN The Chassis Configuration screen, Figure 5-9, allows the user to set the chassis date and time, IP address and Subnet Mask, the operational mode of all modules installed in the chassis, and to view the chassis uptime. Access the Chassis Configuration screen from the Chassis Menu screen by using the arrow keys to highlight the CHASSIS CONFIGURATION menu item and pressing ENTER. The Chassis Configuration screen, Figure 5-9, displays.
PAGE 62
Chapter 5: Local Management IP Address (Modifiable) This field allows the IP address to be set for the 6C105 chassis. If an IP address is assigned to the 6C105 chassis all the interface modules installed in the chassis can be managed via this IP address, eliminating the need to assign an IP address to each interface module. To set the IP address, refer to Section 5.7.1.
PAGE 63
Chassis Configuration Screen Screen Lockout Time (Modifiable) Contains the maximum number of minutes that the Local Management application displays a module’s screen while awaiting input or action from a user. For example, if the number 5 is entered in this field, the user has up to five minutes to respond to each of the specified module’s Local Management screens.
PAGE 64
Chapter 5: Local Management 3. Press ENTER. If the IP address is a valid format, the cursor returns to the beginning of the IP address field. If the entry is not valid, the Event Message Line displays “INVALID IP ADDRESS OR FORMAT ENTERED”. Local Management does not alter the current value and refreshes the IP address field with the previous value. 4. Use the arrow keys to highlight the SAVE command, then press ENTER. The “SAVED OK” message displays indicating that the changes have been saved to memory.
PAGE 65
Chassis Configuration Screen 5.7.3 Setting the Chassis Date The 6C105 is year 2000 compliant, so the Chassis Date may be set beyond the year 1999. To set the chassis date, perform the following steps: 1. Use the arrow keys to highlight the Chassis Date field. 2. Enter the date in an MM/DD/YYYY format. NOTE It is not necessary to add separators between month, day, and year numbers. For example, to set the date to 03/17/1997, type “03171997” in the Chassis Date field. 3.
PAGE 66
Chapter 5: Local Management NOTE When entering the time in the system time field, separators between hours, minutes, and seconds do not need to be added as long as each entry uses two numeric characters. For example, to set the time to 6:45 A.M., type “064500” in the Chassis Time field. 3. Press ENTER to set the system clock to the time in the input field. 4. Use the arrow keys to highlight the SAVE command at the bottom of the screen and press ENTER.
PAGE 67
Chassis Configuration Screen 5.7.6 Setting the Screen Lockout Time The screen lockout time can be set from 1 to 30 minutes with a default of 15 minutes. To set a new lockout time, perform the following steps: 1. Use the arrow keys to highlight the Screen Lockout Time field. 2. Enter a number from 1 to 30. 3. Press ENTER to set the lockout time in the input field. 4. Use the arrow keys to highlight the SAVE command at the bottom of the screen and press ENTER.
PAGE 68
Chapter 5: Local Management WARNING! YOU HAVE ELECTED TO SAVE THE OPERATIONAL MODE FOR THE WHOLE CHASSIS. THIS WILL CAUSE ALL OF THE BOARDS IN THE CHASSIS TO REBOOT. ARE YOU SURE YOU WANT TO SAVE THE NEW OPERATIONAL MODE YES NO 1666 Figure 5-10 Operational Mode Warning Screen 4. Use the arrow keys to highlight the YES command and press ENTER. The changes are saved, and all the modules installed in the chassis reboot. NOTE If the 6E123-50 and 6E133-49 have been set to 802.
PAGE 69
SNMP Community Names Screen 5.8 SNMP COMMUNITY NAMES SCREEN The SNMP Community Names menu item allows the user to set Local Management community names. Community names act as passwords to Local/Remote Management and provide security access to the 6C105. Access to the 6C105 is controlled by enacting any of three different levels of security authorization (read-only, read-write, and super-user).
PAGE 70
Chapter 5: Local Management The following explains each SNMP Community Names screen field: Community Name (Modifiable) Displays the user-defined name through which a user accesses 6C105 management. Any community name assigned here acts as a password to Local/Remote Management. Access Policy (Read-Only) Indicates the access accorded each community name.
PAGE 71
SNMP Community Names Screen NOTE NOTE Any community name assigned in the SNMP Community Names screen is a password to its corresponding level of access to Local Management. The community name assigned Super-User access is the only one that gives the user complete access to Local Management. All passwords assigned in the 6C105 SNMP Community Names screen allow access to both the 6C105 Local Management screens, and the Local Management screens of the interface modules that are installed in the chassis.
PAGE 72
Chapter 5: Local Management 5.9 SNMP TRAPS SCREEN Since the 6C105 is an SNMP compliant device, it can send messages to multiple Network Management Stations to alert users of status changes. The SNMP Traps screen is shown in Figure 5-12. Access the SNMP Traps screen from the Chassis Menu screen by using the arrow keys to highlight the SNMP TRAPS menu item and pressing ENTER. The Chassis SNMP Traps screen displays.
PAGE 73
SNMP Traps Screen Enable Traps (Toggle) Enables transmission of the traps to the network management station with the associated IP address. This field toggles between YES and NO. 5.9.1 Configuring the Trap Table To configure the Trap table, proceed as follows: 1. Using the arrow keys, highlight the appropriate Trap Destination field. 2. Enter the IP Address of the workstation that is to receive traps. IP address entries must follow the DDN format. For example: 134.141.79.121 3. Press ENTER.
PAGE 74
Chapter 5: Local Management 5.10 CHASSIS ENVIRONMENTAL SCREEN The Chassis Environmental menu item allows the user to view chassis environmental information. Access the Chassis Environmental Information screen from the Chassis Menu screen by using the arrow keys to highlight the CHASSIS ENVIRONMENTAL menu item and pressing ENTER. The Chassis Environmental Information screen, Figure 5-13, displays.
PAGE 75
Port Redirect Function Screen 5.11 NOTE PORT REDIRECT FUNCTION SCREEN The Port Redirect Function screen may not be available depending on the operational mode that has been set for the chassis. Refer to your Release Notes to see what operational modes support the Port Redirect Function. Refer to Section 5.7.7, Setting the Operational Mode, for instructions on configuring the operational mode of all the modules installed in the chassis.
PAGE 76
Chapter 5: Local Management Event Message Line 6C105 LOCAL MANAGEMENT Port Redirect Function Source ============ Module Port Destination ============ Port Module 1 1 3 2 ON 1 1 3 3 ON 1 1 3 4 ON 2 2 1 1 OFF 2 2 3 3 ON 3 3 4 4 ON 3 3 5 5 ON 3 3 5 8 OFF Source Port [1] Destination Port [1] Destination Module [1] Source Module [1] SAVE Remap Errors ============ NEXT EXIT Status [ADD] Errors [ON] PREVIOUS RETURN RETURN 2269_66 Figure 5-14 Port Redirect Fu
PAGE 77
Port Redirect Function Screen Destination Module [n] (Selectable) Allows a selected module [n] to be configured as a destination module. Destination Port [n] (Selectable) Allows a selected port [n] to be configured as a destination port. Errors (Toggle) Allows the user to configure the source modules and ports to either send errored frames to selected destination modules and ports (ON option), or to drop errored frames, and send only valid traffic to the destination modules and ports (OFF option).
PAGE 78
Chapter 5: Local Management 4. Press the SPACE bar or BACKSPACE one or more times to increment or decrement the port number displayed in the brackets [n] until the appropriate port number is displayed. 5. Use the arrow keys to highlight the Destination Module field. 6. Use the SPACE bar or BACKSPACE to step to the appropriate module number for the destination module. 7. Use the arrow keys to highlight the Destination Port field. 8.
PAGE 79
Module Selection Screen 5.12 MODULE SELECTION SCREEN The Module Selection screen is the access point to Local Management for all modules installed in the SmartSwitch 6000 chassis. By selecting a module, the Module Menu for the selected device displays. Figure 5-15 shows the Module Selection screen.
PAGE 80
Chapter 5: Local Management Hardware Revision Reflects the hardware version of the module. 5.12.1 Selecting a Module To select an individual module to perform Local Management functions, proceed as follows: 1. Use the arrow keys to highlight the desired module number in the Module # field. 2. Press ENTER, the applicable Module Menu screen displays. Proceed to Section 5.13.
PAGE 81
Module Menu Screen 5.13 NOTE MODULE MENU SCREEN The Local Management screens shown in this chapter are for the 6E123-50. The 6E133-49 shares most of the following Local Management screens. All Local Management functions specific to any interface module are preceded by a note to alert the reader. The 6E123-50 and 6E133-49 Module Menu screens are the access point for all Local Management screens for the 6E123-50 and 6E133-49. Figure 5-16 shows the 6E123-50 Module Menu screen.
PAGE 82
Chapter 5: Local Management The following explains each Module Menu screen field as shown in Figure 5-16: MODULE CONFIGURATION The Module Configuration screen provides access to the Local Management screens that are used to configure the 6E123-50 and 6E133-49. The Module Specific Configuration Menu screen provides access to the screens that allow the user to check 6E123-50 and 6E133-49 resources and set operating parameters specific to each port.
PAGE 83
Module Configuration Menu Screen 5.14 MODULE CONFIGURATION MENU SCREEN The Module Configuration Menu screen, Figure 5-17, provides access to Local Management screens that allow you to configure and monitor operating parameters, modify SNMP community names, set SNMP traps, configure switch parameters and configure 6E123-50 and 6E133-49 ports.
PAGE 84
Chapter 5: Local Management 6E123-50 LOCAL MANAGEMENT Module Configuration Menu Module Type: 6E123-50 Slot Number: X Firmware Revision: XX.XX.XX BOOTPROM Revision: XX.XX.
PAGE 85
Module Configuration Menu Screen SWITCH CONFIGURATION The Switch Configuration screen provides basic setup options for modifying the switching functions of the modules. For details, refer to Section 5.18. SMARTTRUNK CONFIGURATION The SmartTrunk Configuration screen allows the user to logically group interfaces to aggregate high speed uplinks. Refer to the Cabletron Systems SmartTrunk User’s Guide for additional information.
PAGE 86
Chapter 5: Local Management 5.15 GENERAL CONFIGURATION SCREEN The General Configuration screen, Figure 5-18, allows the user to set the system date and time, IP address and subnet mask, the default gateway, the TFTP Gateway IP address, the Operational Mode, the Management Mode, and the COM port configuration. The General Configuration screen also allows the user to Clear NVRAM, and enable or disable IP Fragmentation.
PAGE 87
General Configuration Screen IP Address (Modifiable) This field allows the IP address to be set for the 6E123-50 and 6E133-49. To set the IP address, refer to Section 5.15.1. Subnet Mask (Modifiable) Displays the subnet mask for the module. A subnet mask “masks out” the network bits of the IP address by setting the bits in the mask to 1 when the network treats the corresponding bits in the IP address as part of the network or subnetwork address, or to 0 if the corresponding bit identifies the host.
PAGE 88
Chapter 5: Local Management Screen Lockout Time (Modifiable) Contains the maximum number of minutes that the Local Management application displays a module’s screen while awaiting input or action from a user. For example, if the number 5 is entered in this field, the user has up to five minutes to respond to each of the specified module’s Local Management screens.
PAGE 89
General Configuration Screen NOTE If the user is establishing a remote connection, such as a Telnet or SNMP connection, using the IP address of the module, the chassis LM screens will not be available. To access the chassis LM screens, the IP address of the chassis must be used to establish the connection. In STAND ALONE mode, the module is isolated from the chassis configuration screens, and the module may not be accessed from a module that is in DISTRIBUTED mode.
PAGE 90
Chapter 5: Local Management Clear NVRAM (Toggle) This allows the user to reset NVRAM to the factory default settings. All user-entered parameters, such as IP address and Community Names are then replaced with 6E123-50 and 6E133-49 default configuration settings. For details, refer to Section 5.15.13. IP Fragmentation (Toggle) This field allows the user to enable or disable IP fragmentation. The default setting for this field is ENABLED.
PAGE 91
General Configuration Screen WARNING! YOU HAVE ELECTED TO SAVE ONE OR MORE CONFIGURATION ITEMS THAT REQUIRE RESETTING THIS MODULE. ARE YOU SURE YOU WANT TO CONTINUE? NO YES 174252 Figure 5-19 Configuration Warning Screen 5. Use the arrow keys to highlight the YES command and Press ENTER. The changes are saved and the module reboots. 5.15.
PAGE 92
Chapter 5: Local Management 3. Press ENTER. If the subnet mask is valid, the cursor returns to the beginning of the Subnet Mask field. If the entry is not valid, the Event Message Line displays “INVALID SUBNET MASK OR FORMAT ENTERED”. Local Management does not alter the current value, but it does refresh the Subnet Mask field with the previous value. 4. Use the arrow keys to highlight the SAVE command, then press ENTER. The warning screen shown in Figure 5-19 displays. 5.
PAGE 93
General Configuration Screen 5.15.4 Setting the TFTP Gateway IP Address If the network TFTP server is located on a different IP subnet than the 6E123-50 and 6E133-49, a Gateway IP address should be specified. To set the TFTP Gateway IP address, perform the following steps: 1. Use the arrow keys to highlight the TFTP Gateway IP Address field. 2. Enter the IP address of the TFTP gateway using the DDN format. For example: 134.141.80.122 3. Press ENTER.
PAGE 94
Chapter 5: Local Management 4. Use the arrow keys to highlight the SAVE command at the bottom of the screen and press ENTER. If the date entered is a valid format, the Event Message Line at the top of the screen displays “SAVED OK”. If the entry is not valid, Local Management does not alter the current value, but it does refresh the Module Date field with the previous value. 5.15.
PAGE 95
General Configuration Screen 2. Enter a number from 3 to 99. 3. Press ENTER to set the refresh time to the time entered in the input field. 4. Use the arrow keys to highlight the SAVE command at the bottom of the screen and press ENTER. If the time entered is within the 3 to 99 seconds range, the Event Message Line at the top of the screen displays “SAVED OK”.
PAGE 96
Chapter 5: Local Management 5.15.9 Setting the Operational Mode ! Before setting the operational mode, ensure that the items contained in this caution are fully understood. CAUTION If the module will be configured to operate as a SecureFast switch the following procedures should be performed before setting the operational mode: The module must be assigned a unique IP address. The Management Mode of the module will automatically be set to STANDALONE.
PAGE 97
General Configuration Screen 5.15.10 Setting the Management Mode To set the management mode, perform the following steps: NOTE Upon saving the new Management Mode, the module will reboot. If the module will be set to STANDALONE, ensure the following procedures have been completed: The module has been assigned a unique IP address. The module has been assigned SNMP community names from the module SNMP Community Names screen (Section 5.16).
PAGE 98
Chapter 5: Local Management • American Power Conversion Uninterruptible Power Supply (UPS) connections To configure the COM port, proceed as follows: 1. Use the arrow keys to highlight the Com field. ! CAUTION Do NOT disable or alter the settings of the COM port while operating the current Local Management connection through a terminal. Altering the COM port settings disconnects the Local Management terminal from the port, and ends the Local Management session. 2.
PAGE 99
General Configuration Screen If the 6C105 chassis has been configured with a valid IP address this screen will not appear. When the chassis is assigned a valid IP address all the interface modules installed share this same address. NOTE 3. Use the arrow keys to highlight YES. Press ENTER. 4. If you ENABLED the port, proceed to Section 5.15.12. If you DISABLED the port, use the arrow keys to highlight SAVE at the bottom of the screen, then press ENTER.
PAGE 100
Chapter 5: Local Management ! CAUTION When the COM port is configured to perform the UPS application, all future Local Management connections must be made by establishing a Telnet connection to the module. Ensure that the module has a valid IP address before saving changes to the COM port application. If the module does not have a valid IP address and the changes are saved, refer to Appendix C for instructions on clearing NVRAM in order to reestablish COM port communications. 5.15.
PAGE 101
General Configuration Screen WARNING YOU HAVE ELECTED TO CLEAR NVRAM. THIS WILL CLEAR ALL SYSTEM DEFAULTS INCLUDING BUT NOT LIMITED TO IP ADDRESS, INTERFACE CONFIGURATION, AND COM PORT CONFIGURATION, THEN RESET THE BOARD. ARE YOU SURE YOU WANT TO CLEAR NVRAM? NO YES 174251 Figure 5-21 Clear NVRAM Warning Screen 5. Use the arrow keys to highlight YES and press ENTER. The message “CLEARING NVRAM. REBOOT IN PROGRESS...” displays. The 6E123-50 and 6E133-49 clear NVRAM and reboot.
PAGE 102
Chapter 5: Local Management 5.16 SNMP COMMUNITY NAMES SCREEN The SNMP Community Names menu item allows the user to set Local/Remote Management community names. Community names act as passwords to Local/Remote Management and are agents of security access to the 6E123-50 and 6E133-49. Access to the 6E123-50 and 6E133-49 is controlled by enacting any of three different levels of security authorization (read-only, read-write, and super-user).
PAGE 103
SNMP Community Names Screen Event Message Line 6E123-50 LOCAL MANAGEMENT SNMP Community Names Module Type: 6E123-50 Slot Number: X Firmware Revision: XX.XX.XX BOOTPROM Revision: XX.XX.
PAGE 104
Chapter 5: Local Management super-user This community name permits read-write access to the 6E123-50 and 6E133-49 MIB objects and allows the user to change all modifiable parameters including community names, IP addresses, traps, and SNMP objects. 5.16.1 Establishing Community Names The password used to access Local Management at the Password Screen must have Super-User access in order to view and edit the SNMP Community Names screen.
PAGE 105
SNMP Traps Screen 5.17 SNMP TRAPS SCREEN Since the 6E123-50 and 6E133-49 are SNMP compliant devices, they can send messages to multiple Network Management Stations to alert users of status changes. The SNMP Traps screen is shown in Figure 5-23. It is only necessary to assign SNMP traps if the user desires the traps to be sent to different addresses than those assigned in Section 5.9, which details how to set SNMP Traps for the 6C105 chassis.
PAGE 106
Chapter 5: Local Management Trap Community Name (Modifiable) Displays the Community Name included in the trap message sent to the Network Management Station with the associated IP address. Enable Traps (Toggle) Enables transmission of the traps to the network management station with the associated IP address. This field toggles between YES and NO. 5.17.1 Configuring the Trap Table To configure the Trap Table, proceed as follows: 1. Using the arrow keys, highlight the appropriate Trap Destination field.
PAGE 107
Switch Configuration Screen 5.18 NOTE SWITCH CONFIGURATION SCREEN The Switch Configuration screen will not be available if the operational mode of the module has been set to SECURE FAST VLAN. This screen may only be used by modules configured to operate as 802.1D or 802.1Q switches. The Switch Configuration screen, Figure 5-24, provides the basic setup options to make a switch operational in your network.
PAGE 108
Chapter 5: Local Management Event Message Line 6E123-50 LOCAL MANAGEMENT Switch Configuration Module Type: 6E123-50 Slot Number: X Firmware Revision: XX.XX.XX BOOTPROM Revision: XX.XX.
PAGE 109
Switch Configuration Screen Port # (Read-Only) Lists each switch port on the module. If the number of ports is greater than eight, then the additional ports are listed on subsequent screens. MAC Address (Read-Only) Displays the hardware address assigned to each listed port. State (Read-Only) Disabled: Management disabled this interface. No traffic is received or forwarded while the interface is disabled. Listening: The switch is not adding information to the Transparent Database.
PAGE 110
Chapter 5: Local Management 3. Use the arrow keys to highlight the SAVE command at the bottom of the screen. 4. Press ENTER. The message “SAVED OK” is displayed. 5.18.2 Setting the Age Time To set the Age Time, proceed as follows: 1. Use the arrow keys to highlight the Age Time field. 2. Enter the desired Age Time in increments of 10. The available Age Time range is 10 seconds to 1,000,000 seconds with the default value being 300 seconds. 3.
PAGE 111
Module Specific Configuration Menu Screen 5.19 MODULE SPECIFIC CONFIGURATION MENU SCREEN The Module Specific Configuration Menu screen, Figure 5-25, allows the user to select one of five screens to configure ports or check system resources specific to the 6E123-50 and 6E133-49. NOTE The following menu items on the Module Specific Configuration Menu screen may not display if the operational mode of the module has been set to SECURE FAST VLAN or 802.
PAGE 112
Chapter 5: Local Management 6E123-50 LOCAL MANAGEMENT Module Specific Configuration Menu Module Type: 6E123-50 Slot Number: X Firmware Revision: XX.XX.XX BOOTPROM Revision: XX.XX.
PAGE 113
Module Specific Configuration Menu Screen FLASH DOWNLOAD The FLASH Download screen allows the user to force the 6E123-50 and 6E133-49 to download a new image file to FLASH memory from a TFTP server. For details, refer to Section 5.22. PORT REDIRECT FUNCTION The Port Redirect Function screen allows the user to redirect traffic from one or more ports on the module to a specific destination port on the module. For details, refer to Section 5.23.
PAGE 114
Chapter 5: Local Management 5.20 SYSTEM RESOURCES SCREEN The System Resources screen, Figure 5-26, provides information concerning the processor, the amount of FLASH memory, DRAM, and NVRAM that is installed and how much of that memory is available. Access the System Resources screen from the Module Specific Configuration Menu screen by using the arrow keys to highlight the SYSTEM RESOURCES menu item and pressing ENTER. The System Resources screen displays.
PAGE 115
System Resources Screen Flash Memory Installed (Read-only) Indicates the amount of FLASH memory installed in the 6E123-50 and 6E133-49 and how much is currently available. DRAM Installed (Read-only) Indicates the amount of DRAM installed in the 6E123-50 and 6E133-49 and how much of it is currently available. NVRAM Installed (Read-only) Indicates the amount of NVRAM installed in the 6E123-50 and 6E133-49 and how much of it is currently available.
PAGE 116
Chapter 5: Local Management 5.21 NOTE HIGH SPEED INTERFACE CONFIGURATION MENU SCREEN (6E123-50 ONLY) When the HIGH SPEED CONFIGURATION MENU is selected for the 6E133-49 the applicable HSIM Setup screen displays. Refer to the HSIM User’s Guide to set operating parameters for the HSIM installed in the 6E133-49.
PAGE 117
High Speed Interface Configuration Menu Screen (6E123-50 Only) Event Message Line 6E123-50 LOCAL MANAGEMENT High Speed Interface Configuration Firmware Revision: XX.XX.XX BOOTPROM Revision: XX.XX.XX Module Type: 6E123-50 Slot Number: X Port 5 Port 6 Port Type FE-100TX Unknown Link Status Link No Link Current Oper. Mode 100Base-TXFD [N/A] Desired Oper.
PAGE 118
Chapter 5: Local Management Current Oper. Mode (Read-only) This field displays the current operating mode of ports 5 and 6. Depending on the interface installed (100BASE-FX or 100BASE-TX) this field displays the following: • With a 100BASE-FX interface: 100Base-FX or 100Base-FXFD (full duplex). • With a 100BASE-TX interface: Unknown, 10Base-T, 10Base-TFD (full duplex), 100Base-TX, or 100Base-TXFD (full duplex). Desired Oper.
PAGE 119
High Speed Interface Configuration Menu Screen (6E123-50 Only) Advertised Ability (Selectable) During auto-negotiation, the FE-100TX “tells” the device at the other end of the segment what its capabilities are. The capabilities of a port (5 or 6) with an FE-100TX installed are 10BASE-T, 10BASE-TFD (full duplex mode), 100BASE-TX and 100BASE-TXFD (full duplex mode). In normal operation the FE-100TX “advertises” that it has the ability to operate in any mode.
PAGE 120
Chapter 5: Local Management 5.21.3 Configuring an FE-100TX in Port 5 or 6 In normal operation, a port (5 or 6) with an FE-100TX interface automatically establishes a link with the device at the other end of the segment and no user setup is required. Section 5.21.4 and Section 5.21.5 provide instructions for manually configuring the port with an FE-100TX installed. 5.21.4 Setting the FE-100TX Operational Mode Use this field to set the active technology.
PAGE 121
Flash Download Screen 3. Use the LEFT-ARROW key to move back to the Advertised Ability selection and use the SPACE bar to select the next mode to enable or disable. 4. Use the RIGHT-ARROW key to move across to the Enabled/Disabled field to the right of the selection. 5. Use the SPACE bar to select Enabled or Disabled. Press ENTER. Continue this process until you have completed enabling or disabling the advertised modes. 6. Use the arrow keys to highlight the SAVE command. Press ENTER.
PAGE 122
Chapter 5: Local Management TFTP DOWNLOAD. WILL COMMIT TO FLASH. REBOOT IN PROGRESS... 6E123-50 LOCAL MANAGEMENT Flash Download Firmware Revision: Module Type: 6E123-50 Slot Number: X XX.XX.XX BOOTPROM Revision: XX.XX.XX Download Method: [TFTP] Reboot After Download: [YES] TFTP Gateway IP Addr: 134.141.79.123 Last Image Server IP: 134.141.79.121 Last Image File Name: Download Server IP: Download File Name: EXECUTE RETURN /tftpboot/6E123.hex 134.141.79.121 /tftpboot/6E122.
PAGE 123
Flash Download Screen Reboot After Download (Modifiable when RUNTIME is chosen only) This field notifies the user that the 6E123-50 and 6E133-49 will reboot after the download is complete. If a RUNTIME Download is performed, this field toggles between YES and NO. If YES is selected, the module reboots after the download is completed. If NO is selected the module continues using the existing the firmware image. The module stores the new firmware image in FLASH memory.
PAGE 124
Chapter 5: Local Management 5.22.1 Image File Download Using TFTP Set the 6E123-50 and 6E133-49 to download to FLASH using TFTP as follows: 1. Use the arrow keys to highlight the Download Method field. 2. Use the SPACE bar to select TFTP. 3. Use the arrow keys to highlight the TFTP Gateway IP Addr field. 4. Set the IP address of the TFTP gateway server (this defaults to the same IP address as that set in the TFTP Gateway IP Addr field on the General Configuration screen). 5.
PAGE 125
Flash Download Screen 5.22.2 Image File Download Using RUNTIME Set the 6E123-50 and 6E133-49 to download to FLASH using RUNTIME as follows: 1. Use the arrow keys to highlight the Download Method field. 2. Use the SPACE bar to select RUNTIME. 3. Use the arrow keys to highlight the Reboot After Download field. 4. Use the SPACE bar to select either YES or NO. Select YES if you want the module to reboot after the download is completed.
PAGE 126
Chapter 5: Local Management 5.22.3 Image File Download Using BootP Set the 6E123-50 and 6E133-49 to download to FLASH using BootP as follows: 1. Use the arrow keys to highlight the Download Method field. 2. Use the SPACE bar to select BOOTP. 3. Use the arrow keys to highlight the TFTP Gateway IP Addr field. Set the IP address of the TFTP gateway server (this defaults to the same IP address set in the TFTP Gateway IP Addr field in the General Configuration screen). 4.
PAGE 127
Port Redirect Function Screen NOTE Although all traffic from the source port (including, if desired, errored frames) is sent to the destination port, normal switching is still performed for all frames on the source port. Access the Port Redirect Function screen from the Module Specific Configuration Menu screen by using the arrow keys to highlight the PORT REDIRECT FUNCTION menu item and pressing ENTER. The Port Redirect Function screen displays.
PAGE 128
Chapter 5: Local Management Remap Errors (Read-only) Displays whether the corresponding source ports are configured to send errored frames to the destination ports, or to drop all errored frames before forwarding traffic. Source Port [n] (Selectable) Allows a selected port [n] to be changed to a source port. Destination Port [n] (Selectable) Allows a selected port [n] to be changed to a destination port.
PAGE 129
Broadcast Suppression Screen 7. Use the arrow keys to highlight the Errors field. 8. Use the SPACE bar to select either the ON or OFF option and press ENTER. ON forces the source module and port to forward errored frames to the destination module(s) and port(s). OFF forces the errored frames to be dropped before forwarding traffic. NOTE If more than one port is to be redirected, repeat steps 1 through 8 for each additional setting, then go to step 9 to save all the new settings at once. 9.
PAGE 130
Chapter 5: Local Management Event Message Line 6E123-50 LOCAL MANAGEMENT Broadcast Suppression Module Type: 6E123-50 Slot Number: X Firmware Revision: XX.XX.XX BOOTPROM Revision: XX.XX.
PAGE 131
Broadcast Suppression Screen Reset Peak (Toggle) Allows the user to reset the peak rate. Resetting the Peak Rate also resets the Time Since Peak field. The Reset Peak field toggles between YES and NO. 5.24.1 Setting the Threshold To set the Threshold, proceed as follows: 1. Use the arrow keys to highlight the Threshold field for the selected port. 2. Type in the numbers for the desired limit in increments of 10. 3. Use the arrow keys to highlight the SAVE command at the bottom of the screen. 4.
PAGE 132
Chapter 5: Local Management 5.25 REPEATER CONFIGURATION MENU SCREEN The Repeater Configuration Menu screen, Figure 5-31, is used to access the Repeater Level Security Configuration, or Port Level Security Configuration screen. To access the Repeater Configuration Menu screen from the Module Specific Configuration Menu screen, select the REPEATER CONFIGURATION MENU item and press ENTER. The Repeater Configuration Menu screen displays.
PAGE 133
Repeater Level Security Configuration 5.26 REPEATER LEVEL SECURITY CONFIGURATION The Repeater Level Security Configuration screen, Figure 5-32, is used to set the state of security for all ports on a connector. A connector can be set to receive all frames (NonSecure state), lock on the source address of the next frame received (LockOnNext), or lock on the source address of the last frame received (LockedOnAddr).
PAGE 134
Chapter 5: Local Management The following section defines the fields on the Repeater Level Security Configuration screen. Interface (Read-Only) Indicates the repeater port on the ENET connector (ENET 1 through 4) selected in the Interface field. Refer to Table 5-4 for the ENET/repeater port relationship on the device.
PAGE 135
Repeater Level Security Configuration Action On Intruder (Toggle) Used to select the actions taken for the selected security state. There are two fields to select the actions. Both toggle to activate or deactivate the action. • DisablePort/NoDisable – DisablePort causes the switch to turn off the port that had a security violation. With NoDisable set, the port is not turned off. • SendTrap/NoTrap – SendTrap causes the switch to send an SNMP trap when a port detects a security violation.
PAGE 136
Chapter 5: Local Management 10. Use the arrow keys to highlight the SAVE command. 11. Press ENTER. The message “SAVED OK” displays and all ports of the connector are set to the selected operating mode. 5.27 PORT LEVEL SECURITY CONFIGURATION SCREEN The Port Level Security Configuration screen, Figure 5-33, functions similarly to the Repeater Level Security Configuration screen, except that it is used to set the security of each port of a connector.
PAGE 137
Port Level Security Configuration Screen The following section defines the fields on the Port Level Security Configuration screen. Port (Read-only) Indicates the repeater port on the ENET connector (ENET 1 through 4) selected in the INTERFACE # field. Refer to Table 5-5 for the connector/repeater port relationship on the device.
PAGE 138
Chapter 5: Local Management Action On Intruder (Toggle) Used to select the actions taken for the selected security state. There are two fields to select the actions. Both toggle to activate or deactivate the action. • DisablePort/NoDisable – DisablePort causes the switch to turn off the port that had a security violation. With NoDisable set, the port is not turned off. • SendTrap/NoTrap – SendTrap causes the switch to send an SNMP trap when a port detects a security violation.
PAGE 139
Port Level Security Configuration Screen 7. If the security level chosen causes the DisablePort and SendTrap fields to display under Action On Intruder, use the arrow keys to highlight the DisablePort field. If the security level chosen does not cause the fields to display under Action On Intruder, proceed to step 11. 8. To change the DisablePort setting to NoDisable, press the SPACE bar to toggle the setting. 9. Use the arrow keys to highlight the SendTrap field. 10.
PAGE 140
Chapter 5: Local Management 5.28 MODULE STATISTICS MENU SCREEN The Module Statistics Menu screen, Figure 5-34, provides access to screens that allow the user to obtain switch statistics about frame traffic through each interface, to view MIB-II statistics from each interface, to view RMON Statistics gathered by the RMON agent embedded in the 6E123-50 and 6E133-49 and to view statistics for each repeater port on the 6E123-50 and 6E133-49.
PAGE 141
Switch Statistics Screen The Module Statistics Menu screen displays the following menu items: SWITCH STATISTICS The Switch Statistics screen lists the number of frames received, transmitted, filtered, and forwarded by each interface. INTERFACE STATISTICS The Interface Statistics screen provides the MIB-II statistics for each switched interface, on an interface-by-interface basis.
PAGE 142
Chapter 5: Local Management Access the Switch Statistics screen from the Module Statistics Menu screen by using the arrow keys to highlight the SWITCH STATISTICS menu item and pressing ENTER. The Switch Statistics screen displays. Event Message Line 6E123-50 LOCAL MANAGEMENT Switch Statistics Module Type: 6E123-50 Slot Number: X Port # Firmware Revision: XX.XX.XX BOOTPROM Revision: XX.XX.
PAGE 143
The Interface Statistics Screen CLEAR COUNTERS (Command) This command is used to reset all statistic counters to zero. For details on how to use this field, refer to Section 5.29.1. 5.29.1 Using the Clear Counters Command To reset all the statistics counters to zero, perform the following steps: 1. Use the arrow keys to highlight the CLEAR COUNTERS field. 2. Press ENTER, the counters for the selected port are reset to zero. 5.
PAGE 144
Chapter 5: Local Management Event Message Line 6E123-50 LOCAL MANAGEMENT Interface Statistics Module Type: 6E123-50 Slot Number: X Firmware Revision: XX.XX.XX BOOTPROM Revision: XX.XX.
PAGE 145
The Interface Statistics Screen InNonUnicast (Read-only) This field displays the total number of frames that have been received that were delivered to a broadcast or multicast address. InDiscards (Read-only) The InDiscards field displays the total number of inbound frames that were discarded, even though the frames contained no errors. This field may increment because the switch needed to free up buffer space, or the switch was being overutilized.
PAGE 146
Chapter 5: Local Management OutQLen (Read-only) The OutQLen field displays the length of the packet queue. The field represents the total number of packets that can be contained in the queue. Address (Read-only) This field displays the MAC Address of the interface that is currently being displayed. Last Change (Read-only) This field displays the last time that the interface was reset. Admin Status (Read-only) This field displays the current status of the interface.
PAGE 147
The Interface Statistics Screen 5.30.1 Displaying Interface Statistics To display the statistics for any interface, proceed as follows: 1. Use the arrow keys to highlight the Interface [XX] field at the bottom of the screen. 2. Press the SPACE bar to increment (or press the DEL (delete) key to decrement) the interface number. 3. Press ENTER (neither the Interface # fields nor the statistics will change until ENTER is pressed). 5.30.
PAGE 148
Chapter 5: Local Management 5.31 RMON STATISTICS SCREEN RMON statistics for each interface, on a interface-by-interface basis, are viewed through the RMON Statistics screen shown in Figure 5-37. Access the RMON Statistics screen by using the arrow keys to highlight the RMON STATISTICS menu item on the Module Statistics Menu screen and pressing ENTER. The RMON Statistics screen displays.
PAGE 149
RMON Statistics Screen The following definitions explain each field of the RMON Statistics screen: RMON Index (Read-only) This field displays the current Ethernet interface for which statistics are being shown. The 6E123-50 and 6E133-49 have an embedded RMON agent that gathers statistics for each interface on the module. Data Source (Read-only) This field displays the source of the statistics data that is currently being displayed on the screen.
PAGE 150
Chapter 5: Local Management Multicasts (Read-only) The Multicasts field displays the total number of good frames received that were directed to a multicast address. The value of this field does not include frames directed to the broadcast address. CRC Align Errors (Read-only) This field displays the number of frames with bad Cyclic Redundancy Checks (CRC) received from the network.
PAGE 151
RMON Statistics Screen Total Octets (Read-only) This field displays the total number of octets (bytes) of data, including those in bad frames, received on this interface. 64 Octets (Read-only) Displays the total number of frames including bad frames, received that were 64 bytes in length (excluding framing bits, but including FCS bytes).
PAGE 152
Chapter 5: Local Management 5.31.1 Displaying RMON Statistics To display the statistics for any index, proceed as follows: 1. Use the arrow keys to highlight the Index [XX] field at the bottom of the screen. 2. Press the SPACE bar to increment (or press the DEL [delete] key to decrement) the index number. 3. Press ENTER (neither the RMON Index field nor the statistics will change until ENTER is pressed). 5.31.
PAGE 153
Repeater Statistics Screen 5.32 REPEATER STATISTICS SCREEN Operating statistics for each repeater port (1 through 48) and its corresponding network (ENETs 1 through 4) are displayed via the Repeater Statistics screen shown in Figure 5-38. To access the Repeater Statistics screen, use the arrow keys to highlight the REPEATER STATISTICS menu item on the Module Statistics Menu screen and press ENTER. The Repeater Statistics screen displays.
PAGE 154
Chapter 5: Local Management Port # (Read-Only) Indicates the current port for which statistics are displayed. The port number can be changed by using the PORT # command field at the bottom of the screen. Depending on the port number entered, the Network # field will automatically change to indicate the associated ENET. For details on how to use this field, refer to Section 5.32.1. Bytes Received (Read-only) Displays the number of bytes received.
PAGE 155
Repeater Statistics Screen Oversize Packets (Read-only) Displays the number of packets received with a valid CRC and whose size exceeded 1518 data bytes (not including preamble). Broadcasts (Read-only) Displays the number of broadcasts transmitted and received. Multicasts (Read-only) Displays the number of multicasts transmitted and received. Link Status (Read-only) Indicates if the network or port is linked (Link) or not linked (No Link).
PAGE 156
Chapter 5: Local Management 5.33 NETWORK TOOLS The Network Tools function resides on both the 6E123-50 and 6E133-49 and allows the user to access and manage network devices. Access the Network Tools screen by using the arrow keys to highlight the NETWORK TOOLS menu item in the Module or Chassis Menu screen and pressing ENTER. The Network Tools screen displays.
PAGE 157
Network Tools NOTE The conventions used in describing the commands in Network Tools are as follows: Arguments enclosed by [ ] are required. Arguments enclosed by < > are optional. In the following command examples, the information entered by the user is shown in bold Helvetica font. To abort the output or interrupt a process, press the CONTROL key and c key simultaneously, designated as ^C here. The commands are presented in the following format: command: Syntax: Shows the required command format.
PAGE 158
Chapter 5: Local Management 5.33.1 Built-in Commands The built-in commands listed in this section activate functions on the managed device or devices being accessed through Network Tools. arp: Syntax: arp Description: The arp command provides access to the ARP (Address Resolution Protocol) cache, enabling you to view cache data, delete entries, or add a static route. Super-User access is required to delete an entry or add a static route.
PAGE 159
Network Tools You can specify the arp command without options, or with one of the following options: Options: -a Views cache data -d Deletes an IP address entry. Requires additional arguments: -s Adds a static entry. Requires additional arguments: -f Flushes the ARP cache Example: -> arp -a # Interface # (SonicInt) # (SonicInt) # (SonicInt) # (SonicInt) Network Address 122.144.40.111 122.144.48.109 122.144.52.68 122.144.21.
PAGE 160
Chapter 5: Local Management bridge: Syntax: bridge [ENABLE/DISABLE] [IFNUM/ALL] Description: The bridge command allows each bridge port to be enabled or disabled at the user’s request, either one at a time or all at once. Specifying a single interface number will affect the bridging status of that interface, while specifying ALL will affect every interface.
PAGE 161
Network Tools defroute: Syntax: defroute [interface number] [IP address] Description: The defroute command allows the user to view, set or delete the default IP route to a managed device through the specified interface. Options: Not Applicable Example: -> defroute 2 147.152.42.32 # Default route is 147.152.42.32 on interface 2 -> defroute # Default route is 147.152.42.32 on interface 2 -> defroute delete # Default route is not currently set.
PAGE 162
Chapter 5: Local Management netstat: Syntax: netstat [option] Description: The netstat command provides a display of general network statistics for the managed device. The netstat command must be used with one of the two display options.
PAGE 163
Network Tools reset: Syntax: reset Description: The reset command allows a soft reset of the device. The user will be queried to confirm the reset command to insure against unwanted resets. ! The Network Tools connection to the module will be terminated upon execution of this command.
PAGE 164
Chapter 5: Local Management show: Syntax: show [PROTOCOL] [TABLE] Description: The show command displays information concerning various components of the device. Protocols currently supported are IP, IPX, DECnet, and AppleTalk. Components of those protocols that are currently supported are ARP caches, route tables, FIB tables, server tables, and interface tables. The number of valid entries in the table will be displayed at the end of the table display.
PAGE 165
Network Tools traceroute: Syntax: traceroute [IP address] Description: The traceroute command generates a TRACEROUTE request to a specified IP address and provides a display of all next-hop routers in the path to the device. If the device is not reached, the command displays all next-hop routers to the point of failure. Options: Not Applicable Example: -> traceroute 122.144.11.52 # next-hop[0] : 122.144.60.45 # next-hop[1] : 122.144.8.113 # next-hop[2] : 122.144.61.45 # 122.144.11.
PAGE 166
Chapter 5: Local Management soft_reset: Syntax: soft_reset Description: This command restarts the software image, which restores the user configuration settings from NVRAM. The user will be queried to confirm the reset command to ensure against unwanted resets. ! The Network Tools connection to the module will be terminated upon execution of this command.
PAGE 167
Network Tools telnet: Syntax: telnet [IP address] [Port #] Description: The telnet command allows the user to communicate with another host (that supports Telnet connections) using the Telnet protocol. The user must specify the remote host using its IP address. The [IP address] field is mandatory. If no Port number is specified, telnet will attempt to contact the host at the default port. Options: [Port #] Example: -> telnet 134.141.12.345 Trying 134.141.12.345 Connected to 134.141.12.
PAGE 168
Chapter 5: Local Management link_trap: Syntax: link_trap [enable/disable/status] [PORT/all] Description: The link_trap command allows link traps to be enabled or disabled when specifying a single port, or simultaneously when specifying “all” or no ports. When one or all ports are specified to enable, disable, or find their status, their current condition is displayed.
PAGE 169
Network Tools atm_stp_state: NOTE The atm_stp_state command is only available if an HSIM-A6DP is installed in the module (e.g., 6E13X-25). This command allows the user to enable, disable, or check the current status of the Spanning Tree Algorithm on all ATM interfaces. Syntax: atm_stp_state [STATE] Description: The atm_stp_state command allows the user to enable, disable, or check the status of the Spanning Tree Algorithm on all ATM interfaces.
PAGE 170
Chapter 5: Local Management 5.33.2 Special Commands done, quit, exit: Syntax: done Description: The done command enables the user to exit from Network Tools and return to the Main Menu screen.
PAGE 171
APPENDIX A SPECIFICATIONS This appendix provides operating specifications for the Cabletron Systems 6E123-50 and 6E133-49 Interface Modules. Cabletron Systems reserves the right to change these specifications at any time without notice. A.1 DEVICE SPECIFICATIONS Processor: Dynamic Random Access Memory (DRAM): FLASH Memory: A.2 20 MB 4 MB PHYSICAL PROPERTIES Dimensions: Weight (Unit): MTBF (Predicted): A.3 Intel i960 RISC processor 43.87 H x 5.71 W x 27.88 D (cm) 18.28 H x 2.38 W x 11.62 D (in) 2.
PAGE 172
Appendix A: Specifications A.4 INPUT/OUTPUT PORTS 6E123-50 ENET 1 through ENET 4 Ethernet (10BASE-T compliant) with RJ21 type connectors. Slots for optional Fast Ethernet Slots accept three types of optional Fast Interface Modules Ethernet Interface Modules: the (ports 5 and 6) FE100-TX, FE100-FX and the FE-100F3. 6E133-49 ENET 1 through ENET 4 Ethernet (10BASE-T compliant) with RJ21 type connectors. Slot accepts optional High Speed Interface Module (HSIM). Slot for optional HSIM A.
PAGE 173
Regulatory Compliance A.6 REGULATORY COMPLIANCE Safety The 6E123-50 and 6E133-49 meet the safety requirements of UL 1950, CSA C22.2 No. 950, EN 60950, IEC 950 and 73/23/EEC. Electromagnetic Compatibility (EMC) The 6E123-50 and 6E133-49 meet the requirements of FCC Part 15, EN 50082-1, EN 55022, VCCI V-3, CSA C108.8, AS/NZS 3548 and 89/336/EEC.
PAGE 174
Appendix A: Specifications A-4 6E123-50 and 6E133-49 User’s Guide
PAGE 175
APPENDIX B FE-100TX, FE-100FX AND FE-100F3 SPECIFICATIONS The 6E123-50 supports three Fast Ethernet Interface Modules: • FE-100TX (Section B.1) • FE-100FX (Section B.2) • FE-100F3 (Section B.3) This appendix provides the specifications for these modules. B.1 FE-100TX The FE-100TX uses an RJ45 connector supporting Category 5 Unshielded Twisted Pair (UTP) cabling with an impedance between 85 and 111 ohms. The slide switch on the FE-100TX determines the crossover status of the cable pairs.
PAGE 176
Appendix B: FE-100TX, FE-100FX and FE-100F3 Specifications B.2 FE-100FX The FE-100FX shown in Figure B-2 uses an SC style connector that supports multimode fiber optic cabling. Specifications for the FE-100FX are listed in Table B-1. X FE-100F 6 5 Figure B-2 Table B-1 Cable Type FE-100FX Transmitter Power Worst Case Budget Typical Budget 50/125 µm fiber 6.0 dB 9.0 dB 62.5/125 µm fiber 9.0 dB 12.0 dB 100/140 µm fiber 15.0 dB 18.
PAGE 177
FE-100F3 B.3 FE-100F3 The FE-100F3 shown in Figure B-3 uses an SC style connector that supports single mode fiber optic cabling. Specifications for the FE-100F3 are listed in Table B-2. 3 FE-100F 6 5 Figure B-3 Table B-2 Cable Type FE-100F3 Transmitter Power Worst Case Budget Typical Budget 8/125 µm fiber >10.0 dB <10.0 dB 12/125 µm fiber >10.0 dB <10.0 dB NOTE The transmitter power levels and receive sensitivity levels listed are peak power levels after optical overshoot.
PAGE 178
Appendix B: FE-100TX, FE-100FX and FE-100F3 Specifications B-4 6E123-50 and 6E133-49 User’s Guide
PAGE 179
APPENDIX C OPTIONAL INSTALLATIONS AND MODE SWITCH BANK SETTINGS This appendix covers the following items: • Required tools (Section C.1) • Locations, functions, and settings for the mode switches (Section C.2) • Installing Optional Fast Ethernet Interface Modules (Section C.3) C.1 REQUIRED TOOLS You need the following tools to perform the procedures provided in this appendix: • Antistatic wrist strap (provided with 6C105 chassis) • Phillips screwdriver C.
PAGE 180
Appendix C: Optional Installations and Mode Switch Bank Settings Figure C-1 shows the location of the mode switches and the switch settings for normal operation. MODE SWITCH BANK Flash OFF ON 1 2 3 4 DRAM 5 6 7 8 Figure C-1 6E123-50 and 6E133-49 Mode Switch Location/Component Layout Switch definitions and positions are as follows: • Switches 1 through 4 – For Cabletron Systems use only. • Switch 5 – COM Port Autobaud.
PAGE 181
Setting the Mode Switches • After changing the position of switch 6 and restarting the module, the 6E123-50 and 6E133-49 request a new image download until they either receive a new image or the RESET button on the front panel is pressed. When the RESET button is pressed, the 6E123-50 and 6E133-49 continue trying to contact a BootP server, but will time out in approximately one minute. If the module times out, the image is downloaded from its FLASH memory. • Switch 7 – Clear NVRAM.
PAGE 182
Appendix C: Optional Installations and Mode Switch Bank Settings C.3 INSTALLING OPTIONAL FAST ETHERNET INTERFACE MODULES Figure C-2 shows the location of the Fast Ethernet Interface Module connectors on the 6E123-50 boards for port slots 5 and 6. NOTE For instructions on installing a High Speed Interface Module (HSIM) in the 6E133-49, refer to the applicable HSIM documentation.
PAGE 183
Installing Optional Fast Ethernet Interface Modules To install a Fast Ethernet Interface Module in port slot 5 or 6 of the 6E123-50, proceed as follows: ! CAUTION ! CAUTION The Fast Ethernet Interface Module and the host module are sensitive to static discharges. Use an antistatic wrist strap and observe all static precautions during this procedure. Failure to do so could damage the Fast Ethernet Interface Module or the host module. The FE-100F3 uses Class 1 lasers.
PAGE 184
Appendix C: Optional Installations and Mode Switch Bank Settings Coverplate Rear Standoff Front Standoffs 5 6 Figure C-3 Coverplate Removal 2. Remove the screw from the rear standoff. Save the screw. ! CAUTION When installing an FE-100FX or FE-100F3 module into the host module, remove the rubber plug on the SC connector before proceeding. 3. See Figure C-4. Gently pull the faceplate of the host module forward to allow room for the Fast Ethernet Interface Modules to be aligned over the connector.
PAGE 185
Installing Optional Fast Ethernet Interface Modules Module Module Connector FE-1 00T X 10 100 Rear Standoff Motherboard Connector Front Standoffs 5 6 Figure C-4 Installing the Fast Ethernet Interface Module 5. Press down firmly on the Fast Ethernet Interface Module until the pins slide all the way into the motherboard connector. Ensure that the Fast Ethernet Interface Module seats flush on the standoffs. 6. Secure the Fast Ethernet Interface Module with the screws saved in steps 1 and 2. 7.
PAGE 186
Appendix C: Optional Installations and Mode Switch Bank Settings C-8 6E123-50 and 6E133-49 User’s Guide
PAGE 187
INDEX Numerics 100BASE-TX cable length 2-2 10BASE-T connection 3-6 requirements 2-2 802.
PAGE 188
Index H Module Operational Mode 5-42, 5-50 Module Selection screen 5-33 Module Specific Configuration Menu screen 5-65 Broadcast Suppression 5-67 Flash Download 5-67 High Speed Interface Configuration 5-66 System Resources 5-66 Module Statistics 5-36 Module Statistics Menu screen 5-94 Interface statistics 5-95 RMON statistics 5-95 Switch statistics 5-95 Module time 5-41 Module Uptime 5-42 Help related manuals 1-12 technical support 1-11 High Speed Interface screen 5-70 advertised ability 5-73 configuring
PAGE 189
Index O Operational Mode 5-17 P Password screen 5-7 Peak switch utilization 5-69 Physical properties A-1 Port Redirect Function 5-29, 5-67 R Repeater Statistics for ENETs 1 4 5-107 Repeater Statistics screen network # 5-107 Repeater Statistics screen, ENETs 1 4 administration status 5-109 alignment errors 5-108 broadcasts transmitted/received 5-109 bytes 5-108 clear counters 5-109 collisions 5-108 CRC errors 5-108 frames 5-108 link status 5-109 multicasts transmitted/received 5-109 OOW collisions 5-108 o
PAGE 190
Index Spanning Tree Algorithm 5-62 Specifications A-1 Standards compatibility 1-5 Subnet mask 5-16, 5-18, 5-41, 5-45 Switch address 5-62 Switch Configuration screen 5-61 Age Time 5-62 MAC address 5-63 Setting the Age Time 5-64 Setting the port status 5-64 Setting the STA 5-63 State 5-63 Status 5-63 Switch address 5-62 type of STA 5-62 Switch Statistics screen 5-95 System Resources screen 5-68 current switch utilization 5-69 DRAM installed 5-69 Flash memory installed 5-69 NVRAM installed 5-69 peak switch uti