INSTRUCTION MANUAL DVP14 Video Wall Processor DVI Output Cascadable 4 Output Displays Dual-View
THIS PAGE IS LEFT INTENTIONALLY BLANK
Safety and Notice The DVP14 DVI output Cascadable Video Wall Processor, 4-Display Dual-View has been tested for conformance to safety regulations and requirements, and has been certified for international use. However, like all electronic equipment, the DVP14 should be used with care. Please read and follow the safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit. ● Follow all instructions and warnings marked on this unit.
Table of Contents INTRODUCTION.............................................................3 FEATURES.......................................................................4 SPECIFICATIONS...........................................................5 PACKAGE CONTENTS..................................................6 INPUTS AND OUTPUTS...................................................6 SUPPORTED RESOLUTION.............................................7 HARDWARE INSTALLATION....................................
INTRODUCTION The DVP14 Cascadable Video Wall Processor, 4-Display DualView DVI Output is a powerful most cost effective, and fully real time data/video processor for multiple flat panel displays or projectors. With high-definition real-time DVI output, the quality of the video wall is guaranteed. The output display is scalable up to 255 by 255 squares. Virtually any setup for the display layout may be possible by the provided software.
Features ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● Four DVI outputs from 640x480 to 1920x1200 Local DVI loop output for monitoring the DVI input only Supports HDMI, DVI, S-Video, CVBS, Component, and VGA input, from 640x480 to 1920x1200, interlaced or progressive Advanced video de-interlacing for improving 480i and 576i SD video input PIP (picture-in-picture), PAP or PBP (Picture by Picture), Full screen modes and adjustable size & position through software Resize, position, flip, zoom output video Perfect as a vide
Specifications Model Name DVP14 Technical Typical usage Output displays Input Format Support Video-wall processor 4 HDMI / DVI / VGA / YPbPr / S-Video / CVBS [One digital and one analog can be used in PIP or PAP mode] Output Support DVI (HDMI by adapter) Video loop-out Yes, DVI HDCP compliance No Video bandwidth Video support Audio support HDMI / DVI [Single-link 4.95Gbps] VGA [165MHz] Up to 1920x1200@60 / 1600x1200@60 Control No RS-232 PIP/PAP Cascadable Yes Yes Input TMDS signal 1.
Package Contents ● ● ● ● ● 1x DVP14 1x UL AC C13 power cord 1x VGA to component breakout cable 1x Composite, S-video breakout cable 1x DVI/VGA breakout cable ● ● ● ● ● 1x Rack-mounting ear set 1x Installation software CD 1x User Manual 1x USB to RS-232 cable 1x DVI to VGA adapter Inputs and Outputs The DVP14 can use up to two inputs at one time and supports multiple input interfaces (HDMI, DVI, composite, S-Video, component, VGA (adapters needed)) and accepts both graphics and video signals, which come
Supported Resolution [DVI-I digital only IN] Socket Supported Mode Resolution Supported Mode Resolution 480p / 525p 720x483 @60Hz MAC 832x624 @75Hz 480p (16:9) 960x483 @60Hz VESA 1024x768 @60Hz 576p / 625p 720x756 @50Hz MAC 1024x768 @60Hz (HDTV) 720p 1280x720 @50Hz VESA 1024x768 @70Hz (HDTV) 720p 1280x720 @60Hz IBM 1024x768 @72Hz (HDTV) 1080p 1920x1080 @30Hz VESA 1024x768 @75Hz VESA 720x400 @85Hz MAC 1024x768 @75Hz VESA 640x350 @85Hz VESA 1024x768 @85Hz VESA 640x400 @85H
Digital Visual Interface (DVI) to HDMI Female The unit has DVI-I Female connectors for Input and Outputs: DVI-I [29-pin Female, digital only] Recommended Adapter Connector you can use from DVI to HDMI Female DVI-I (Dal Link) to HDMI Female DVI-D (Dual Link) to HDMI Female [DVI-I digital only Out] Socket Supported Mode Resolution (HDTV) 720p 1280x720 @50Hz (HDTV) 720p 1280x720 @60Hz (HDTV) 1080p 1920x1080 @60Hz VESA 640x480 @60Hz VESA 800x600 @60Hz VESA 1024x768 @60Hz VESA
Hardware Installation Safety Precautions 1. To prevent fire or shock hazards, do not expose this device to rain or moisture. 2. When connecting other products such as DVD players, and personal computers, you should turn off the power of this product and the other devices for protection against electric shocks. 3. The product should be placed more than one foot away from heat sources such as radiators, heat registers, stoves, and other products (including amplifiers) that produce heat.
Installation Procedures Unpacking Remove the DVP14 from the shipping box and examine it for any signs of shipping damage or missing items (check with package contents above). All shipping items should be saved if the product is to be moved or returned for service. Shipping unit back to CE labs or dealer for service not in the original box may result in voiding warranty or additional cost. Placement Please do not block the sides of this device or stack another device on the top or bottom of the DVP14.
Connection Diagram 9 11
OPERATION SOFTWARE System Requirement and Precautions 1. After turning off the DVP14; please wait at least 15 seconds to allow the power capacitors to be discharged before reapplying power. 2. The DVP14 comes with a software control program which runs under Microsoft Windows 98, 2000, XP. The application controls the DVP14 through a RS-232 serial data control interface. 3. Before you run the software please, make sure you have a RS-232 cable connected between your computer COM port and the DVP14. 4.
Software Operation Main Control Panel State Overall state and format setting: 1. Save and Read: The current layout of the four DVI outputs ports can be saved to a file. In addition, the file can be uploaded in the future to restore the setting. 2. Display Setting / Aspect Ratio: The main and sub sources both can be adjusted to 16:9 or 4:3. The brightness and contrast of the mixed video also can be adjusted for different requirements. After setting, please press Update Setting to save the change. 3.
Setting Use this button to configure the correct COM port for serial control, and the device ID for identification. Connect Establish communications with the DVP14 and the computer. Disconnect Disconnect the computer COM port from the DVP14. Input Resolution Setting the resolution of the input port. 1. After 10 secongs, the new setting can be applied to the DVP14, but the input source and Display layout mode will return to default. 2. Please reset input source and Display layout mode.
Setup Individual Output DVI ports (Channel) There are a total of 4 DVI output ports for theDVP14. Each DVI output can be independently set up to display any area of the input video. Each output can be set to a different output resolution to adapt different combinations of monitors or projectors.
1 2 3 This screen representation area will demonstrate the resulting selection of the input video to be displayed for the selected DVI output port. "Original Input Video" shows the resolution information of the input video to each output channel, and it will vary depending upon the input video. "Original Resolution" Section Setup the output resolution for individual DVI output port.
5 “Fine Tune by Percentage” will provide the option to further adjust the position and area defined in 4 . For outward expansion For inward reduction By percentage, users need to determine what will be the reference. There are two choices for this part: "Specified Area" and "Fulll Input".
Using the TV wall Calculator Continued 2. Open the Software DVP14 video wall processor and select the TV Wall Calculator, under the Connect selection: 3. Measure the length and height of the screen as shown below and fill in the boxes in the Calculator (inch) Section, then Select the configuration. Select 2x2. Then Select "Calculate".
4. When you are finished, this window will pop up. Pess OK. Click X to close the "TV Wall Calculator" window. 5. On the Display Output section, Select: Display Output 1, and you will see that the data has changed automatically. Then press: (2) Write setting to device. 6. On the Display Output section, Select: Display Output 2, and you will see that the data has changed automatically. Then press: (2) Write setting to device. Repeat this step for Output #3 and Output #4.
7. After you press: Write setting to device. From Port #1 to Port #4, you will see the video wall. 8. The margins will be very close. If you are not satisfied, go back to Step #5 to fine-tune the yellow marked data to get a smoother image between screen to screen. Do this adjustment on each screen as needed. Remember push "Write setting to Device" each time you make an adjustment.
TROUBLESHOOTING Problem No power Recommendations • • No or Erratic Video • • • Poor quality • • Wrong color • Check the AC power cord to ensure proper insertion into the DVP14 and at the wall socket. If using a power strip, verify switch is on and the circuit breaker is not tripped. If you are recovering from a power outage or intentional AC power disconnection, leave the device off for a minute and then power it on again.
WARRANTY The SELLER warrants the DVP14 DVI output, Cascadable, Video wall Processor, 4-Display Dual-View to be free from defects in the material and workmanship for 1 year from the date of purchase from the SELLER or an authorized dealer.
The content of this manual has been carefully checked and is believed to be accurate. However, The SELLER assumes no responsibility for any inaccuracies that may be contained in this manual. The SELLER will NOT be liable for direct, indirect, incidental, special, or consequential damages resulting from any defect or omission in this manual, even if advised of the possibility of such damages.
INSTALLER NOTES Purchasing Date: S/N: 24
INSTALLER NOTES Purchasing Date: S/N: 25
CE labs can support many areas of your audio and video distribution needs. We manufacture: • Digital Signage software and Media Players • HD Matrix Switchers • RF amplifiers • HDMI and Component HD distribution amplifiers • CAT 5 Signal Extenders • VGA Extenders and Splitters • and cables of all types. See our full product line at www.celabs.net WARRANTY Cable Electronics, Inc.
