Specifications

2. Standard Specifications
© DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
2-2
 Electric Specifications 1
Model
Item
DVP-
14ES00ϭ
DVP-
24ES00ϭ
DVP-
32ES00ϭ
DVP-
60ES00ϭ
DVP-
20EX00ϭ
DVP-
14ES01ϭ
DVP-
24ES01ϭ
DVP-
32ES01ϭ
DVP-
20EX11ϭ
Power Supply Voltage / Fuse
100~240VAC (-15%~10%), 50/60Hz ± 5% / 2 A / 250VAC
24VDC (-15%~10%) / 2 A / 250VAC
Input Power Operating
Characteristics
95-100VAC is needed to start the PLC.
If the voltage drops to 70VAC or less, the PLC will stop.
A minimum of 18VDC is needed to start the PLC.
If the voltage drops below 17.5VDC, the PLC will stop.
Maximum Power Loss Time 10ms or less 5ms or less
Power Consumption 20 VA 25VA 30VA 35VA 30 VA 5.5 W 6.5 W 8 W 10 W
DC24V Supply Current 400mA 400mA 400mA 200mA 400mA ΫΫΫΫ
Power Protection DC24V output short circuit DC24V input polarity
Withstand Voltage 1500VAC(Primary-secondary), 1500VAC(Primary-PE), 500VAC(Secondary-PE)
Insulation Resistance >5 MӨ at 500VDC (Between all inputs/outputs and earth)
Noise Immunity
ESD: 8KV Air Discharge
EFT: Power Line: 2KV, Digital I/O: 1KV, Analog & Communication I/O: 250V
Damped-Oscillatory Wave: Power Line: 1KV, Digital I/O: 1KV
RS: 26MHz~1GHz, 10V/m
Grounding
The diameter of grounding wire cannot be smaller than the wire diameter of terminals
L and N (All DVP units should be grounded directly to
the ground pole).
Environment
Operation: 0к~55к (Temperature), 50~95% (Humidity); Storage: -25к~70к (Temperature), 5~95% (Humidity)
Pollution degree 2
Vibration /Shock Immunity Standard: IEC1131-2, IEC68-2-6 (Test Fc) / IEC 1131-2 & IEC68-2-27 (Test Ea)
Weight (g) 400 552 580 750 536 260 414 430 386
Input Point Electric Specification Output Point Electric Specification
Input Point Type Digit I/O Analog I/O (EX) Output Point Type Relay-R Transistor-T Analog I/O (EX)
Current Spec. 2A/1 point (5A/COM) 0.3A/1point (1.2 A/COM) 0~20mA
Input Point Spec.
DC (Sink or Source)
24VDC 5mA
Input Voltage: -10V~+10V (Input Resistance: 40KO)
Input Current: -20mA~+20mA(Input Resistance: 250O)
Voltage Spec.
Below 250VAC,
30VDC
30VDC 0V~+10V
100 VA (Inductive)
Active Level
(Analog Input Resolution)
OFFШON Above 10VDC
ONШOFF Below 9VDC
Input Voltage Resolution: 10bit
Input Current Resolution: 10bit
Maximum Load
120 W (Resistive)
9W 0.2W
Reaction Time
About 10ms (Adjust
D1020 and D1021 can
be 0~15ms)
5ms (Adjusting D1118 can change reaction time)
Reaction Time About 10ms
OFFШON 20Ӵs
ONШOFF 30Ӵs
10ms
Resolution
ΫΫ
8 bit