CS7 UNDERWATER METAL DETECTOR OPERATING INSTRUCTIONS
CS7 - RAPID GET YOU GOING INSTRUCTIONS 1. Assemble and set stem to desired length. (Neatly twist surplus lead around stem close to the handle, and secure with self securing straps). 2. Adjust head to correct angle and tighten both head bolt. 3. Fit batteries and secure battery compartment cover, ensure ‘o’ ring seal is clean before replacing cover and forms a visibly good seal all round after screws are tightened. 4. Set FREQUENCY to BATT. CHECK position. 5.
CONTENTS: PAGE INTRODUCTION ASSEMBLY BATTERIES BATTERY CHECK CONTROLS AND WHAT THEY DO OPERATING YOUR CS7 IMPORTANT CONSIDERATIONS ACCESSORIES (OPTIONAL) AVAILABLE FROM C-SCOPE CARE OF YOUR DETECTOR LIMITATION OF WARRANTY DETECTOR NOT OPERATING? FURTHER INFORMATION 6 6 7 7 8 10 10 10 10 11 11 12 © C-Scope International Limited The information contained in this manual was correct at the time of going to press.
Controls A C-Scope CS7 C D B E F G I K J H A B C D E F G H I J K Upper Stem Adjustable Handle Detachable Control Box Battery Compartment Stem Bolt Lower Stem Head Securing Bolt Batt.
INTRODUCTION To protect your investment complete both sections of the enclosed guarantee card and return the reply paid portion to C-Scope (UK only). This is particularly important in order to obtain the free second year parts guarantee. Please retain the original packing box. In the event that your detector should ever require to be serviced, this package will be most suitable for postal protection. C-Scope detectors are recognised as the finest detectors available.
BATTERIES The CS7 is powered by eight AA batteries (not supplied) available from garages, department stores, etc. or a single 12v rechargeable pack from C-Scope. It is advisable to use standard batteries to start with. You can then evaluate the sort of use you give the detector and decide whether the investment in rechargeables is justified. The batteries should be fitted in the holder which is Battery Compartment located in the battery compartment.
comes on the batteries should be replaced, or recharged in the case of rechargeable batteries. B) Turn the THRESHOLD control to OFF. Checking The Batteries Red Green Yellow CONTROLS AND WHAT THEY DO The control panel comprises two rotary controls, signal and battery condition indicators. i. ON/OFF - THRESHOLD control is used to set the audio tone of the machine. This is normally set so that the tone is silent or just on the point where the tone is starting to break through.
ii. BATTERY CHECK - FREQUENCY control has two main functions in addition to the battery test which is at the switched, fully anti-clockwise position. Small changes to the frequency setting can be used to minimise interference from other signal sources. Changing the frequency also affects the machine’s sensitivity to aluminium alloy based rubbish such as silver paper and pull tabs. By rotating the control clockwise, the machine’s sensitivity to such objects will be progressively increased.
OPERATING YOUR CS7 Check the batteries are in good condition prior to, and frequently during the search. With the search head away from metals, the THRESHOLD control is increased to the point just below that at which the continuous audio tone is heard. This is the setting that will allow the user to get the best results. The FREQUENCY control can then be adjusted to the desired position.
any terrain, but misuse or lack of due attention will tell in the end. After using your detector in a hostile environment (salt water, sand, etc.) the exterior parts should be flushed with clean fresh water, paying particular attention to clean all mating and moving surfaces of sand or silt which, if left, can have severe detrimental effects on the durability of your CS7 detector. The use of solvents or detergents should be avoided. Particular attention should be paid to the ‘O’ ring seals.
FURTHER INFORMATION If you experience any difficulty in operating your CS7, or have any questions on the information in your CS7 Operating Instructions Manual, please do not hesitate to phone our Customer Service Department on 44(0)1233629181. Before returning a detector for repair to C-Scope ensure you have done the following:(a) Read the instructions thoroughly. (b) Tried new batteries and checked procedure outlined above. (c) Return your detector with a letter giving full details of fault.
