Test Report No.: NK2GR079 Appendix F – USER’S Manual CMOTech Co., Ltd.
CDU-550 Modem User Guide
FCC RF EXPOSURE COMPLIANCE In August 1996 the Federal Communications Commission (FCC) of the United States with its action in Report and Order FCC 96-326 adopted an updated safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC regulated transmitters. Those guidelines are consistent with the safety standard previously set by both U.S. and international standards bodies. The design of this modem complies with the FCC guidelines and these international standards.
■ Reorient or relocate the receiving antenna ■ Increase the separation distance between the equipment and the receiver ■ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ■ Consult the dealer or an experienced Radio/TV technician for help.
-Medical Devices Industry Association recommends the patients using a pacemaker not to use RF using devices such as cell phones, wireless modems and so on because using those devices in the range of 15cm from the pacemaker may affect the pacemaker. In an inevitable situation, make it sure to keep the distance of more than 15cm between the modem and the pacemaker. To minimize the possible interference, use the modem on the opposite side of the pacemaker. Do not use it if possible.
CDU-550 Modem Install Setup Insert installation CD (supplied with CMOTech Data Modem) into the CD-ROM drive. This will automatically start the installation and install the required drivers plus CMOTech Data Modem Application software. Do not connect CMOTech Data Modem into your laptop/PC yet. The installation procedures are the Windows 2000 and Windows XP. Start setup If the auto run does not start after inserting the CD, please double-click on Setup.exe file on CD-ROM to start the installation.
Start Auto Run Install Shield Wizard...
Choose the installation directory and click "Next" to continue. Click "Install" to continue.
CMOTech Modem is configuring your new software installation.
Check device Installation Complete. Click Finish and remove the installation CD.
Insert Modem Please Insert Modem On Window 2000 As inserting Modem on Window 2000, there will not be any window and users can run applications after the device is detected. On Window XP If your operation system is XP on inserting Modem, you can see Find New Hardware Dialog.
Using the CDU-550 Modem Application Software During this installation a Shortcut will have been placed on your desktop for the CMOTech Data Modem Application software. Note : If the modem is connected to the Laptop/PC via serial port, the user will have to select the serial port initially when the User Interface software starts up. On auto start of the Application Software, the first screen you will see Main window.
Setting MIN / MDN The modem will be rebooted.
Indicator state Icons Icon Meaning Icon Meaning No Signal Roaming Antenna / Signal Strength Coverage Icon. CDMA 1x available Current High Data Rate mode selected : Hybrid Mode (1xEV-DO Preferred) DEFAULT. The modem will automatically look for the highest speed network available in this mode. Coverage Icon. IS95 available only Current High Data Rate mode selected: CDMA 1X only Mode Coverage Icon. 1xEV-DO available Current High Data Rate mode selected: 1xEV-DO only Mode.
Dial up Network Connection Clicking the selected Connect button. The Application Software will start dialing the Service Option under dial-up when the Connect button is clicked (The Connect button can be clicked on the main window).
Verifying User. Registering your computer on the network.
You can see above window s right blue icon. This icon show on connection. Warning : If you install Windows XP service pack 2, you must turn off firewall in Window security center. If you try connecting with turn on firewall, you can see connecting fail.
Active and Dormant state It is on Active state when an active icon during Dialup, it goes to Dormant state. appears on the window.If having no data transmission Users can discern that it is on Dormant state with an icon displayed on the screen.
Option General NOTE : The Apply button must be clicked for any changes to take effect. Application Software auto run : This Check box determines whether the Application Software starts automatically when the Modem is connected. Check the check box and press Apply button.
Hibernation : With the Application Software running (idle). Windows will not hibernate or switch to standby mode. Please select this option under General tab to close UI automatically so that windows can hibernate or switch to standby.
Data Connection setting To Setting Dial-Up connection, click Option button and click Data button. Also to change connecting type, click the radio Button. NOTE : You can use Packet, QNC type in 1X current coverage. And can t use Packet type in IS 95 coverage. Connecting is also possible to connect (Dial-up) by clicking the connect button on the main window without opening the Dial-up setting window. When clicking the connect button, the last Service option will be used for dial up.
Always On is a CDMA 1x internet domain that applies to data (in Kilobytes) based charging packages. This service allows you to remain connected to the internet all the time. charges will apply to the amount of data sent and received with this domain. Dial-up Networking - QNC Standard. When you are not within CDMA 1x coverage or you have not subscribed to CDMA 1x, you can still connect to operator's Standard Mobile internet Service using Quick Net Connect, provided you are withis CDMA coverage.
Data Logs The User Data Counter will continuously accumulate on each session and will only clear when Clear Data Count is clicked.
Uninstall Uninstall CMOTech CDU-550 Modem To uninstall CMOTech CDU-550 Modem driver, click Uninstall . Start uninstall Execute the Uninstall program. Execute setup.
Auto Run Press button As clicking Uninstall icon, you can see a dialog below. Click yes button. Uninstall continue. Uninstall program remove file in your PC. (Uninstall Program deletes Drivers, Modem and Modem Application Program.
Uninstall Complete. Click Finish button.
