Specifications

1 - 8 0 0 - 6 3 3 - 0 4 0 5
e11-68
Operator Interface
Volume 14
USB Connectivity
Part No. EA-MG-PGM-CBL
C-more Micro-Graphic Programming
Connections
<--->
USB to RS-232 Converter Specifications
Part Number
EEAA--MMGG--PPGGMM--CCBBLL
Hardware
USB Interface
USB Specification Rev. 1.1
Connector: USB Type B jack to accept USB Type B cable plug
Serial Interface
RS-232 (EIA-232-E)
Connector: RJ12 phone jack 6p to accept RJ12 cable plug
Baud Rate
115.2 kbps Maximum
Input Voltage
5 VDC (Supplied thru serial interface cable.)
Power Consumption
50 mA (Does not include power to panel and/or bezel.)
Accessory Cables (included)
USB Cable
USB Type A plug to PC on one end, USB Type B plug to converter on other end, 0.30 m [1 foot] length (* Note)
Serial Cable
RJ12 phone plug connectors on both ends, 2.0 m [6.56 feet] length (* Note)
Physical
Dimensions
2.559” (W) x 1.417” (H) x 0.886” (D)
[65.0 mm x 36.0 mm x 22.5 mm]
Weight
1.06 oz. [30 g]
Environmental
See Micro-Graphic panel specifications at the beginning of this catalog section.
* Note: Maximum cable length for either the USB or serial cable should not exceed 2.0 m [6.56 feet] in length.
C-more STN Micro-Graphic Programming Connection
Using the
CC--mmoorree
Micro-Graphic Programming Software for project
development, STN
CC--mmoorree
Micro-Graphic panels can be connected to a PC (personal
computer) by using EA-MG-PGM-CBL, the USB-to-RS-232 cable assembly.
• Connect the USB programming cable (included) from a USB port type A on the PC to the USB
type B port on the converter (included). Next connect the serial programming cable from the
converter’s RJ12 port to the panel’s RJ12 serial port. The panel receives power from the USB
port of the PC that it is connected to through the USB to RS-232 converter assembly.
User PC
U
SB
C
able
S
erial
C
able
C-more 3”
Micro-Graphic
Panel
PC to Panel Programming
Cable Assembly
(
Includes serial & USB cables)
p
/n EA-MG-PGM-CBL
USB to RS232
C
onverter
NOTE: The TFT panels EA1-T4CL and EA1-T6CL do NOT use the EA-MG-PGM-CBL
assembly. The TFT panels use a standard USB A-to-B type cable such as USB-CBL-AB6.
See below.
Part Number Description Price
USB-CBL-AB3
Standard 3-ft. (0.9 m) USB 2.0 cable, A-type connector to B-type connector, used to connect personal computer to any
CC--mmoorree
touch
panel for setup and programming. (Note: Touch panels require a 24 VDC power source for configuration and operation.)
<--->
USB-CBL-AB6
Standard 6-ft. (1.8 m) USB 2.0 cable, A-type connector to B-type connector, used to connect personal computer to any
CC--mmoorree
touch
panel for setup and programming. (Note: Touch panels require a 24 VDC power source for configuration and operation.)
<--->
USB-CBL-AB10
Standard 10-ft (3 meter) USB 2.0 cable, A-type connector to B-type connector, used to connect personal computer to any
CC--mmoorree
touch
panel for setup and programming. (Note: Touch panels require a 24 VDC power source for configuration and operation.)
<--->
USB-CBL-AB15
Standard 15-ft. (4.6 m) USB 2.0 cable, A-type connector to B-type connector, used to connect personal computer to any
CC--mmoorree
touch
panel for setup and programming. (Note: Touch panels require a 24 VDC power source for configuration and operation.)
<--->
C-more TFT Micro-Graphic Programming Connection
The
CC--mmoorree
TFT Micro-Graphic panels EA1-T4CL and EA1-T6CL include an integral USB to serial converter. It is programmed via any
USB Type A to Type B cable.
When properly installed on your PC, the device driver will be assigned a communication port number and appear in Windows Device
Manager as a serial com port.
USB cable options for programming EA1-T4CL and EA1-T6CL
USB to RS-232 Programming Cable
Assembly