Specifications
1-800-633-0405
B10–38
Operator Interface
C-more 6” Micro-Graphic Specifications
NOTE: The environmental specifications for the panels shown
above are also applicable for the
C-more
6” Micro-Graphic
accessories shown later in this section of the catalog.
Specifications
Electrical
Low Power Mode* High Power Mode
• Input Voltage Range
5.0 VDC (4.75 – 5.25 VDC) 12/24 VDC (10.2 – 26.4 VDC)
• Input Power
Supplied through the panel’s RJ12 serial communications
port connection when used with most AutomationDirect PLCs
having a RJ12 communication port or from a PC USB.
Supplied from an external 12-24 VDC power source
• Power Consumption
1.05 W @ 5 VDC (210 mA) 6.5 W @ 10.2 VDC (630 mA)
• Recommended Fuse
No fuse required when directly connected to a PLC or PC
with recommended cable.
Type AGC fast acting glass fuse,
750 mA, 250 VAC, ADC p/n AGC-75
• Maximum Inrush Current
1 A for 500 µs 10 A for 500 µs
• Acceptable External
Power Drop Duration
Maximum 1 ms
Environmental
• Operating Temperature
0 to 50 °C (32 to 122 °F)
• Storage Temperature
–20 to +60 °C (–4 to +140 °F)
• Humidity
5–95% RH (non-condensing)
• Environmental Air
No corrosive gases permitted
• Vibration
IEC60068-2-6 (Test Fc), 5-9 Hz: 3.5 mm amplitude, 9-150 Hz: 1.0G, sweeping, at a rate of
1 octave/min. (±10%), 10 sweep cycles per axis on each of 3 mutually perpendicular axes
• Shock
IEC60068-2-27 (Test Ea), 15 G peak, 11 ms duration, three shocks in each direction per axis,
on 3 mutually perpendicular axes (total of 18 shocks)
• Noise Immunity
NEMA ICS3-304
RFI, (145 MHz, 440 Mhz 10 W @ 10 cm)
Impulse 1000 V @ 1 µs pulse
• Enclosure
NEMA 4/4X, IP-65 (When mounted correctly, for indoor use only.)
• Agency Approvals
CE (EN61131-2), UL508, CUL Canadian C22.2 No. 142-M95, UL File E157382
Physical
• Dimensions
6.850” (W) x 5.331” (H) x 2.130” (D) [174.0 mm x 135.4 mm x 54.1 mm] (Landscape Mode)
5.331” (W) x 6.850” (H) x 2.130” (D) [135.4 mm x 174.0 mm x 54.1 mm] (Portrait Mode)
• Enclosure Mounting
Thickness Range
0.04” – 0.2” [1 – 5 mm]
• Mounting Clip Screw
Torque Range
21 – 28 oz-in [0.15 – 0.2 Nm]
• Depth from bezel rear
with options Module
1.894” [47.1 mm]
• Weight
30.69 oz. (870 g)
*NOTE: When the panel is powered through Port1 from a connected PLC or PC, the screen
brightness is diminished because the panel is running in Low-Power Mode. For full brightness,
connect an external 12-24 VDC power source to the panel’s power connection. Low-Power
Mode should be used during initial programming only. Connect an external 12-24 VDC power
source when the panel is installed in its application.